SUPERLIGHTINGLED R15 Zone RGB Remote Control Owner’s Manual
- June 12, 2024
- SuperLightingLED
Table of Contents
1 Zone / 4 Zone RGB RF Remote Controller
Model No.: R15/R16
1 and 4 zone RGB/ Touch color wheel/Wireless remote 30m distance/cr2032
battery
Features
-
Apply to RGB LED controller, dimming driver or smart lamp.
Ultra sensitive color adjustment touch wheel. -
Adopt 2.4GHz wireless technology, remote distance up to 30m.
-
Each remote can match one or more receiver.
-
Battery powered (CR2032).
-
Operate with LED indicator light.
-
White & Black available.
Technical Parameters
Input and Output
Output signal | RF(2.4GHz) |
---|---|
Working voltage | 3VDC(CR2032) |
Working current | <5mA |
Standby current | <1 OpA |
Standby time | 1 year |
Remote distance | 30m(Barrier-free space) |
Safety and EMC
EMC standard (EMC)| ETSI EN 301 489-1 V2.2.3
ETSI EN 301 489-17 V3.2.4
---|---
Safety standard(LVD)| EN 62368-1:2020+A11:2020
Radio Equipment(RED)| ETSI EN 300 328 V2.2.2
Certi| CE,EMC,LVD,RED
Environment
Operation temperature | Ta: -30° C ~ +55 °C |
---|
Package
Size | L114 x W65 x H20mm |
---|---|
Gross weight | 0.062kg |
Warranty
Warranty | 5 years |
---|
Mechanical Structures and Installations
Note:
- Before the first use, please remove the protective film on the battery.
- If the LED indicator is not on when press key, it is due to dead battery or bad contact caused by multiple plugging, please replace the battery, or raise the battery shrapnel with a screwdriver.
To fix the remote, two options are offered for selection:
Option 1: fix the remote’ back holder on the wall with two screws.
Option 2: adhere the remote’ back holder to the wall with paster.
Operation
- When light is on, touch the color wheel, the indicator will display red.
- To extend battery life, no touch or press key operation after a few seconds, the touch wheel will enter sleep state, you need press any key to make touch wheel quit sleep state.
Match Remote Control (two match ways)
End user can choose the suitable match/delete ways. Two options are offered
for selection:
Use the controller’s Match key
Match:
Short press match key, immediately press on/off key (single zone remote) or
zone key (multiple zone remote) of the remote.
The LED indicator fast flash a few times means match is successful.
Delete:
Press and hold match key for 5s to delete all match, The LED indicator fast
flash a few times means all matched remotes were deleted.
Use Power Restart
Match:
Switch off the power, then switch on power, repeat again.
Immediately short press on/off key (single zone remote) or zone key (multiple
zone remote) 3 times on the remote.
The light blinks 3 times means match is successful.
Delete:
Switch off the power, then switch on power, repeat again.
Immediately short press on/off key (single zone remote) or zone key (multiple
zone remote) 5 times on the remote.
The light blinks 5 times means all matched remotes were deleted.
Key function
R15: 1 zone RGB remote
On/Off: Turn on/off light.
Color wheel: Touch to change static RGB color.
R/G/B: Get red, green or blue color directly.
Mode+/-: Short press run the next or previous dynamic mode, long press Mode+
2s run mode cycle.
Speed+/-: For dynamic mode, adjust speed, short press 10 levels, long press 2s
get the fastest or slowest speed.
For static color, adjust saturation, namely change current static color to
mixed white slowly, short press 11 levels, long press for continuous
adjustment.
Brightness+/-: Adjust brightness, short press 10 levels, long press for
continuous adjustment.
R16: 4 zone RGB remote
On/Off: Short press turn on/off all zone light.
1, 2, 3, 4 zone: Short press select and turn on zone light, long press 2s turn
off zone light.
Short press multiple zone key fastly, will select multiple zone synchronously.
Color wheel: Touch to change current zone static RGB color.
Mode: Short press run the next dynamic mode, long press 2s run mode cycle.
Brightness+/-: Adjust brightness, short press 10 levels, long press for
continuous adjustment.
Speed: For dynamic mode, adjust speed, short press 10 levels, long press 2s
get the default speed.
For static color, adjust saturation, namely change current static color to
mixed white slowly, short press 11 levels, long press for continuous
adjustment.
Scene: One scene memory, short press recall the scene, long press 2s save the
current color into the scene. 4 zone recall or save synchronously.
Safety information
-
Read all instructions carefully before you begin this installation.
-
When installing battery, pay attention to the battery positive and negative polarity.
A long time without the remote control, remove the battery.
When remote distance becomes smaller and insensitive, replace the battery. -
If no response from the receiver, please re-match the remote.
-
Gently handle remote, beware of falling.
-
For indoor and dry location use only.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>