BEGA 24 480 Wall Luminaire Instruction Manual
- June 12, 2024
- BEGA
Table of Contents
Technical amendments reserved
Wall luminaire
24 480
Instructions for use
Application
Wall luminaire with two-sided light output.
For illumination and design tasks in architecture.
The light directed downwards is intended to illuminate the wall and the
horizontal surface in front of it.
The light directed upwards is intended to illuminate the wall and ceiling
surfaces.
Product description
Luminaire made of aluminium alloy, aluminium and stainless steel BEGA Unidure®
coating technology Colour graphite, silver or white Matt safety glass
Reflector surface made of pure aluminium Mounting plate with 2 fixing holes ø
4.4 mm · 62 x 95 mm spacing 2 cable entries for through-wiring of mains supply
cable ø 7-12 mm
Connecting terminal 2.5@ with plug connection Earth conductor connection LED
power supply unit 220-240 V ****0/50-60 Hz
BEGA Thermal Control® Temporary thermal regulation to protect temperature-
sensitive components without switching off the luminaire
Safety class I Protection class IP 65
Dust-tight and protection against water jets
Impact strength IK05
Protection against mechanical impacts < 0.7 joule
– Safety mark
**** – Conformity mark
Weight: 2.3 kg
This product contains light sources of energy efficiency class(es) C, D
Safety
The installation and operation of this luminaire are subject to national
safety regulations.
Installation and commissioning may only be carried out by a qualified
electrician.
The manufacturer accepts no liability for damage caused by improper use or
installation. If subsequent modifications are made to the luminaire, the
person responsible for these modifications shall be considered the
manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e. g. transients, etc. we
recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.
Lamp
| Module connected wattage | 16.8 W |
|---|---|
| Luminaire connected wattage | 19 W |
| Rated temperature | ta = 25 °C |
| Ambient temperature | ta max = 50 °C |
24 480 K3
| Module designation | 2x LED-1145/830 |
|---|---|
| Colour temperature | 3000 K |
| Colour rendering index | CRI > 80 |
| Module luminous flux | 2960 lm |
| Luminaire luminous flux | 2090 lm |
| Luminaire luminous efficiency | 110 lm / W |
24 480 K4
| Module designation | 2x LED-1145/840 |
|---|---|
| Colour temperature | 4000 K |
| Colour rendering index | CRI > 80 |
| Module luminous flux | 3110 lm |
| Luminaire luminous flux | 2196 lm |
| Luminaire luminous efficiency | 115,6 lm / W |
Lighting technology
Wall luminaire with broad spread light distribution.
Half beam angle of the light distribution in both half spaces 72°.
Installation
LED are high-quality electronic components!
Please avoid touching the light output opening of the LED directly during
installation or relamping.
Undo hexagon socket head screws (wrench size 3 mm) up to the stop and
disassemble the mounting plate.
Pass the power connecting cable through the cable entry in the mounting plate.
Fix the mounting plate with enclosed or any other suitable fixing material
onto the mounting surface.
Make earth conductor connection and electrical connection to the connecting
terminal (plug connection).
Push plug into coupler as far as it will go.
Place luminaire housing onto the mounting plate and fix it.
Make sure that gasket is positioned correctly.
Please note:
Do not remove the desiccant bag from the luminaire housing.
It is needed to remove residual moisture.
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt and deposits.
Do not use high pressure cleaners.
Replacing the LED module
The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to
those of the modules originally fitted.
The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire.
Please follow the installation instructions for the LED module.
Inspect and, if necessary, replace the luminaire gaskets.
Defective glass must be replaced.
Close the luminaire.
Spares
LED power supply unit DEV-0475/500
LED module 3000 K LED-1145/830
LED module 4000 K LED-1145/840
Reflector wide beam 76 001 976
Gasket mounting box 83 002 074
Gasket housing 83 002 075
BEGA Gantenbrink-Leuchten KG
Postfach 31 60
58689 Menden
info@bega.com
www.bega.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>