technical pro OFB18M 18 Inch Rechargeable Floor Fan Instruction Manual

OFB18M 18 Inch Rechargeable Floor Fan
Instruction Manual

RECHARGEABLE FAN
AC/DC OPERATED RECHARGEABLE FAN
WITH SUPER BRIGHT LED LIGHT

OFB18M 18 Inch Rechargeable Floor Fan

Please read these instructions before first use:

1: Fan blade
2: LED light
3: Button
4: Battery level indicator
5: Speed level indicator
6: Expansion link| 7: Adapter sleeve
8: Oscillating switch
9: Battery cover
10: AC port
11: Rotary knob for expansion link
12: USB scket
---|---

ATTENTION

1. Please read this instruction before first use
2. Please ensure that the voltage indicated on the appliance corresponds with the mains voltage.
3. When the lead gets dim, please recharge the product.
4. Charge at least once every 3 months for 8 hours even when the appliance is not in use.
5. Please keep the fan switch in OFF status when not in use.
6. The suitable operating ambient humidity level is 0 C-40 C
7. Avoid using in water or moisture.

HOW TO USE THE FAN

1. ON /OFF function: Press ON/OFF to choose to turn on or turn off the fan. The battery level indicator will show the capacity of the battery as in picture 2.
2. SPEED function: Press SPEED to choose any speed you like. The fan will start from 3-speed (as in picture 3). The fan will be cycled by 4-5-1-2-3 after every press.
3. TIMER function: Press TIMER to choose the expected timing hours. Press one time means the interval time is 1 hour (Speed level indicator shows Number 1 ). Press one more time, Press one more time, which means the interval time is 2 hours (Speed level indicator shows Number 2). By that analogy, the max timing is 8 hours.
4. LIGHT function: Press the LIGHT button to choose to turn on or turn off the LED light.
5. When plug into the AC power, the fan will charge automatically (the battery level indicator will not stop running until it is fully charged).
6. The fan has an oscillating knob as picture4.you can choose an oscillating or stationary in any angle.
7. Unscrew the Adapter sleeve ( part 7) can adjust the height of the expansion link, max available space is 200mm. can use the rotary knob to fix the right height you like.

HOW TO ASSEMBLE THE FAN

1. Please find the M8 nut and screw, and fix the fan head into the body, please refer to picture 7.
2. Please find the parts as picture 8 shows, and assemble them one by one as shown.
3. Please use the rotary knob to fix the body and base as in picture 9.
4. After finishing these steps,it will be the same like picture 10.
5. Please refer to picture 11, and assemble parts 7.6.5.4.3.2.one by one.
6. The completed fan will be the same as in picture 12.

HOW TO CHARGE THE FAN

1. Please ensure that the voltage indicated on the appliance corresponds with the mains voltage.
2. Plug in the cord to the AC socket.
3. A red indicator shows that the battery is getting charged.
4. It is a normal phenomenon of slight heat while charging the battery.

HOW TO CHANGE THE BATTERY

1. Loosen the fixing screw on the battery cover as in picture 13.
2. Take out the battery.
3. Put the new battery inside, and connect “+” to the red cord, and “—” to the black cord, must follow it.
4. Put on the cover and tighten the screw.

HOW TO USE THE REMOTE CONTROL

1. Put a 2pcs AAA battery inside of the remote control before using it.
2. Press the control button, and choose different modes, (Please refer to HOW TO USE)
3. Please take the battery out if not been in use for a long time.

SPECIFICATION

Built-in battery: 2x6V 4.5Ah rechargeable lead acid battery 6pcs 0.1W SMD LED light
Power source:110-220V 50/60Hz
Charge time: 8-12 hours
Working time:
5-speed: 2.5 hours
4-speed: 3.5 hours
3-speed: 7 hours
2-speed: 15 hours
1-speed: 30 hours
LED light: 50 hours Max power: 40W
Product size: 500x407x1408 mm

WARNING :

1. The product may not be abandoned in the life waste. The battery should be special recycling after abandoning, as it will harmful to the environment.
2. If the supply cord of the fas is damaged,it shall be exclusively replaced by the manufacturer or his service agent or a similarly qualified person in order to avoid a hazard
3. This appliance is not intended for use by persons (including children) with reduced physical sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for the safety.
4. Children should be supervised to ensure that they do not play with the appliance.

Step 1: Find the nut (1) & bolt (2), screw the Body and Head together.

Step 2: Locate the base accessories and use the Lever Screw (3) to attach the Pole to the Base.

The Extension Bar is located inside the Pole. Use the Adjuster to loosen the bar for retrieval.
Step3 : Attach the Body built in STE  ONE to the Base built in STEP TWO using the Knob Screw (4).

Use the adjuster to fixate the height of the Extension Bar.

Step 4: Assemble the wind cover as shown. Back Cover(5), Washer Ring(6), Fan Blade(7), Fixed Cap(8), Front Cover(9) Emblem Cov-er(10). Once all have been assembled, use the Clips (11) included on the covers to hold it all in place.

Step 5: Unscrew & Open the battery cover. Take out the battery, from the Body, connect the red wire to the “+” terminal & black wire to the”-” terminal, cover the back and tighten the screw

Questions? Call 1-718-567-7754

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>