Optimant Lighting B094499HWK Gold Pendant Lighting Instruction Manual

B094499HWK Gold Pendant Lighting

WARNING (To reduce the risk of fire, electric shock, or personal injury):

1. We suggest installation by a licensed electrician.

2. Please read the instruction carefully and save it as you may need it at later time.

3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
   A) Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
   B) Place the wall switch in the “OFF” position.

4. Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all side. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.

5. Make sure that the ceiling or wall can stand the weight of the lamp before installation.

6. Make sure the voltage you are using is 120V. The maximum wattage is 40W per bulb.

7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.

8. When replacing bulb, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.

9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGEFORFINISHEDPRODUCT：

TOOLS REQUIRED (NOT INCLUDED):
Before starting assembly and installation please prepare the needed tools as below picture

PARTS TYPE & QTY INCLUDING:

(C) Mounting plate (1)
(D) Green ground screw (1)
(E) Canopy (1)
(F) Swivel joint (1)
(G) Knob ball (2)
(H) Tube
(I) Iron frame (1)
(J) Socket (3)
(K) Plastic washer (3)
(L) Screw (3)
(M) Iron shade (1)

ACCESSORIES & QTY ENCLOSED:

(A) Plastic wire connector (3)
(B) Mounting screw (2)

ASSEMBLY & INSTALLATION INSTRUCTIONS:

1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.

2. Turn off power
   Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
   A) Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
   B) Place the wall switch in the “OFF” position.

3. Unscrew the knob balls (G) from canopy (E) then remove the mounting plate (C).

4. Thread the screws (L) through the plastic washers (K), then align the holes in the iron shade (M) and the iron frame (I).
   Then fix the iron shade (M) to the iron frame (I) with screws (L) and the plastic washers (K).
   Hand tighten till snug.

5. 1. According to your desired hanging height to choose and use the tubes (H). Then pass the fixture wires through the tubes (H), the swivel joint (F) and the canopy (E).

2. Thread the chosen tubes (H) together and attach tubes (H) to the top of iron frame (I).
   Thread the chosen tubes (H), the canopy (E) and swivel joint (F) together till snug.

6. Attach the mounting plate (C) to outlet box with the mounting screws (B).

7. Make wire connections
   Connect wires as below wires connection shown.
   PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
   Connect ground wires according to the below chart Connect wires according to the below chart
   Twist wires together with plastic wire connector (A) until tightly joined, then carefully tuck all wires into the outlet box. NOTE: be sure that no wire strands are exposed.

8. Connect Black or Red Supply Wire to:	Connect White Supply Wire to:
   Black	White
   *Parallel cord ( round & smooth )	*Parallel cord ( square & ridged )
   Clear,Brown,Gold or Black without tracer	Clear,Brown,Gold or Black with

   tracer
   Insulated wire ( other than green ) with copper conductor| Insulated wire ( other than green ) with silver conductor

*Note: When parallel wires ( SPT I & SPT II ) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (see illus.)

9. Raise canopy (E) to ceiling and secure canopy (E) in place by tightening knob balls (G) onto the pre-assembled threaded nipples on the mounting plate (C).
   Note: The canopy (E) should be snug against the ceiling and the knob balls (G). If not, adjust the length of the threaded nipples on the mounting plate assembly (C) by unscrewing the pre-assembled hex nuts and then screwing the preassembled threaded nipples in or out of the mounting plate (C) until the secure length is achieved. Tighten the pre-assembled hex nuts and back to step 8.

10. Install bulb (Not included) (Please do not exceed the maximum wattage recommended on the socket.)

CLEANING.

To clean, wipe the fixture with a soft cloth. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

ORDERING PARTS.

Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>