Conrad FPPS 24-24W Power Pack Instruction Manual

Conrad FPPS 24-24W Power Pack

Product Information

Product Usage Instructions

The FPPS 24-24W POWER PACK is a power supply unit designed to provide voltage to low-voltage devices with compatible DC jacks. It is suitable for use with common household mains voltage ranging from 100 V to 240 V/AC and a frequency of 50/60 Hz.

Before using the power pack, please ensure the following:

1. Read the operating instructions carefully and familiarize yourself with the safety information.
2. Make sure the power consumption of the device you are connecting does not exceed the nominal voltage of the power pack.
3. Ensure that the power pack is connected to a suitable power outlet.

To use the FPPS 24-24W POWER PACK, follow these steps:

1. Connect the power pack to a compatible power outlet using the provided cable.
2. Connect your low-voltage device to the power pack using a compatible DC jack.
3. Ensure that the LED indicator on the power pack lights up, indicating that there is power supply.
4. If there are any issues or the LED indicator does not light up, refer to the problem troubleshooting section in the user manual and follow the recommended solutions.

For maintenance and cleaning of the power pack, please refer to the user manual for detailed instructions.
Please note that this product is intended for indoor use only and should not be used outdoors. Avoid contact with moisture, such as in bathrooms, at all times. Do not modify or rebuild the product as it may result in damage or hazards. Keep the operating instructions in a safe place and only provide the product to third parties along with its operating instructions. For further assistance or technical support, please contact our customer service or other qualified personnel.

Intended Use
The power pack serves as voltage supply for low-voltage devices with matching DC jacks. It is intended for connection to common household mains voltage (100 – 240 V/AC, 50/60 Hz). A galvanic separated DC voltage is applied to the output. The power consumption of the consuming device may not exceed the nominal voltage of the respective power pack (depends on the type). The product has a protection against short circuit and overload. This product fulfils European and national requirements related to electromagnetic compatibility (EMC). CE conformity has been verified and the relevant statements and documents have been deposited at the manufacturer. It is intended for indoor use only. Do not use it outdoors. Contact with moisture, e.g. in bathrooms, must be avoided under all circumstances. For safety and approval purposes, you must not rebuild and/or modify this product. If you use the product for purposes other than those described above, the product may be damaged. In addition, improper use can result in short circuits, fires, electric shocks or other hazards. Read the instructions carefully and store them in a safe place. Make this product available to third parties only together with its operating instructions. This product complies with the statutory national and European requirements. All company names and prod-uct names are trademarks of their respective owners. All rights reserved.

Delivery Content

• Power pack
• Operating instructions

Up-to-date Operating Instructions
Download the latest operating instructions at www.conrad.com/downloads or scan the QR code shown. Follow the instructions on the website.

Explanation of Symbols

• The symbol warns of dangerous voltage that can lead to personal injury by electric shock.
• The symbol warns of hazards that can lead to personal injury.
• The arrow symbol indicates special information and advice on operation.
• This symbol indicates that the product meets the energy efficiency requirements for Class VI.

Safety Instructions

Read the operating instructions carefully and especially observe the safety information. If you do not follow the safety instructions and information on proper handling in this manual, we assume no liability for any resulting personal injury or damage to property. Such cases will invalidate the warranty/guarantee.

General Information

• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may become dangerous playing material for children.
• Protect the appliance from extreme temperatures, direct sunlight, strong jolts, high humidity, moisture, flammable gases, steam and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and protect it from any accidental use. Safe operation can no longer be guaranteed if the product:
  • is visibly damaged,
  •  is no longer working properly,
  • has been stored for extended periods in poor ambient conditions or
  • has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height can dam-age the product.
• Never touch the device with wet or moist hands. There is a danger of electrocution.
• On commercial premises, the accident prevention regulations of the relevant professional insurance association for electrical systems and operating materials are to be observed.
• Operation in unfavourable ambient conditions is not permitted. Adverse ambient conditions are:
  • moisture or excessive humidity
  • dust and combustible gases, vapours or solvents
• Since the device generates heat when operating, ensure that it is adequately ventilated. The housing must not be covered!
• Never switch the device on immediately after having taken it from a cold to a warm environ-ment. Under adverse conditions, the resulting condensation could destroy the device. Allow the device to reach room temperature before switching it on.
• Power units are not designed for application to human beings or animals.
• Consult an expert when in doubt about the operation, safety or connection of the appliance.
• Maintenance, modifications and repairs must only be completed by a technician or an authorized repair centre.
• If you have questions which remain unanswered by these operating instructions, contact our technical support service or other technical personnel.

Connected Devices

• Also observe the safety and operating instructions of any other devices which are connected to the product.

Operation

• Periodically check the technical safety of the device, e.g. check for damage to the housing etc.
• Always lay the cable so that nobody can trip over or become entangled in it. This poses a risk of injury.
• Connect the DC plug of the power pack with the DC jack on the low-voltage device.
• The polarity cannot be altered. The plug has the fixed polarity “inside plus (+), outside minus (-)”.
• Make sure that the consumer is switched off when connected to the power pack.
• Plug the power pack into a standard domestic wall socket. Correct operation is signaled at the power pack by a LED.
• To remove the consumer, proceed in reverse sequence.

Troubleshooting
By purchasing the power pack you have acquired a product that has been designed to the state of the art and is operationally reliable. Problems and malfunctions can occur nevertheless.

We would therefore like to show how you can rectify certain faults yourself:

• Observe the safety instructions by all means!

of the power outlet.
Check the correct fit of the power outlet.
Power pack overloaded.| Remove the consumer and check the technical data.

Care and Cleaning

• Disconnect the product from the mains before each cleaning.
• Do not use any aggressive cleaning agents, rubbing alcohol or other chemical solutions as they can cause damage to the housing and malfunctioning.
• Clean the product with a dry, fibre-free cloth.
• Disposal
  This symbol must appear on any electrical and electronic equipment placed on the EU market. This symbol indicates that this device should not be disposed of as unsorted municipal waste at the end of its service life.
  Owners of WEEE (Waste from Electrical and Electronic Equipment) shall dispose of it separate-ly from unsorted municipal waste. Spent batteries and accumulators, which are not enclosed by the WEEE, as well as lamps that can be removed from the WEEE in a non-destructive manner, must be removed by end users from the WEEE in a non-destructive manner before it is handed over to a collection point.

Distributors of electrical and electronic equipment are legally obliged to provide free take-back of waste. Conrad provides the following return options free of charge (more details on our website):

• in our Conrad offices
• at the Conrad collection points
• at the collection points of public waste management authorities or the collection points set up by manu-facturers or distributors within the meaning of the ElektroG

End users are responsible for deleting personal data from the WEEE to be disposed of. It should be noted that different obligations about the return or recycling of WEEE may apply in countries outside of Germany.

Technical Data

Data according to EU regulation 2019/1782

Other
Cable length……………………………………1.8 m
Plug Ø:……………………………………………5.5 mm (outer) / 2.1 mm (inner)
Operating conditions…………………………0 to +25 ºC, 20 – 85 % RH
Storage conditions……………………………-20 to +50 ºC, 10 – 90 % RH
Dimensions (W x H x D)……………………51 x 77.4 x 87.5 mm
Weight……………………………………………168 g
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent the technical status at the time of printing.
Copyright 2023 by Conrad Electronic SE.

References

• Conrad Electronic » All parts of success
• Download center

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>