BEGA 51261.4 LED Wall Luminaire for Indoor Use Instruction Manual

Table of Contents

BEGA-51261-4-LED-Wall-Luminaire-for-Indoor-Use-fig-1

The product is a luminaire that requires installation and operation according to national safety regulations. It is recommended to have a qualified electrician handle the installation and commissioning. The manufacturer will not be held liable for damage caused by improper use or installation. Additional overvoltage protection components are recommended for enhanced protection against transients.
The luminaire features LED modules with a connected wattage of 27W or 31W. The rated temperature ranges from 25 to 45 degrees Celsius, and the ambient temperature should also be within this range. The module designation is 51 261.4 K3.
The colour temperature of the LED module is 3000K, providing a warm white light. The colour rendering index (CRI) is greater than 90, indicating high-quality colour reproduction. The module has a luminous flux of 4200 lumens, while the luminaire itself emits 2033 lumens. The luminaire’s luminous efficiency is 65.6 lumens per watt.
During installation or relamping, it is important to avoid touching the light output opening of the LED directly due to the high-quality electronic components used.
The product’s spares include the DEV-0388/700i LED power supply unit and the LED-1319/930 LED module with a diffusor, both operating at a colour temperature of 3000K.

Ensure that the luminaire is installed and operated in compliance with national safety regulations.
For installation and commissioning, it is recommended to hire a qualified electrician.
If any modifications are made to the luminaire, ensure that the person responsible for these modifications is considered the manufacturer.
Consider using separate overvoltage protection components to enhance protection against transients. These components can be found on the manufacturer’s website at www.bega.com.
Handle the LED modules with care during installation and avoid touching the light output opening directly.
Ensure that the connected wattage of the LED module is either 27W or 31W.
Maintain the rated temperature range of 25 to 45 degrees Celsius for both the module and the ambient temperature.
Take note of the module designation, which is 51 261.4 K3.
Consider the colour temperature of the LED module, which is 3000K, providing a warm white light.
The colour rendering index (CRI) is greater than 90, indicating high-quality colour reproduction.
The module has a luminous flux of 4200 lumens, while the luminaire emits 2033 lumens.
The luminaire’s luminous efficiency is 65.6 lumens per watt.
Refer to the manufacturer’s website for spares, including the DEV-0388/700i LED power supply unit and the LED-1319/930 LED module with a diffusor.

BEGA-51261-4-LED-Wall-Luminaire-for-Indoor-Use-fig-2

Wall luminaire · indoor luminaire with light emission on two sides for the glare free illumination of wall surfaces with the mounting surface being the reflection surface.
A luminaire which allows interesting illumination concepts individually or in rows.

Luminaire housing made of aluminium, finish Colour matt brass
Silicone light diffuser
3 elongated fixing holes
Width 4.5 mm · 340 mm spacing
Mounting plate with several openings for cable entry and through-wiring for mains cable Connecting terminals 2.5@
Earth conductor connection
LED power supply unit
220-240 V x 0/50-60 Hz
DC 176-264 V
DALI-controllable
Number of DALI addresses: 1
Basic insulation is provided between the mains and control cables
BEGA Thermal Control®
Temporary thermal regulation to protect temperature-sensitive components without switching off the luminaire
Safety class I
c – Conformity mark
Weight: 2.9 kg
This product contains light sources of energy efficiency class(es) D

The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to
the luminaire, the person responsible for these modifications shall be considered the manufacturer.

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.

Lamp
- Module connected wattage 27 W
- Luminaire connected wattage 31 W
- Rated temperature ta = 25 °C
- Ambient temperature t a max = 45 °C
51 261.4 K3
- Module designation 2x LED-1319/930
- Colour temperature 3000 K
- Colour rendering index CRI > 90
- Module luminous flux 4200 lm
- Luminaire luminous flux 2033 lm
- Luminaire luminous efficiency 65,6 lm / W

LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping.

Undo the hexagon socket head screws (wrench size 3 mm) and lift luminaire housing. Loosen earth connection (plug connection) between luminaire housing and mounting plate. Pass the power connecting cable through one of the openings of the mounting plate.
Fasten the mounting plate with the supplied fastening material or other suitable fastening material to the installation surface.
Note position of application of the mounting plate “arrow down”.
Make the electrical connection to the terminals. Please ensure correct wire assignment for the connecting cable.
Connect the earth conductor to the green-yellow wire (1). Connect the live conductor to the brown wire (L) and the neutral conductor to the blue wire (N).
Use the terminals marked DA, DA for digital control.
If these terminals are not used, the luminaire will operate at full light output.
Make earth connection (plug connection) between luminaire housing and mounting plate again.
Hang the luminaire housing in the mounting plate and screw it in place with the hexagon socket head screws.

Clean luminaire regularly with solvent-free cleansers from dirt.

The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by qualified persons using standard tools.
Disconnect the system from the power supply. Press the synthetic LED cover together lengthwise and remove it from the housing profile.
Remove the LED module. Install the replacement LED module.
Please follow the installation instructions for the LED module.
A defective LED cover must be replaced.