CONRAD 1006452 Trailing Edge Dimmer with DALI Control Input and Push-Function for LED Lighting User Manual
- June 12, 2024
- CONRAD
Table of Contents
1006452 Trailing Edge Dimmer with DALI Control
Input and Push-Function for LED Lighting
User Manual
INSTRUCTION MANUAL PART A
Trailing Edge Dimmer with DALI Control Input and Push-Function for LED Lighting
| Uin 100-240V AC | Uout 100-240V AC | Iout 1,8A max. |
|---|---|---|
| DALI (in)2mA max. | DALI (in)2mA max. |
The installation requires expert knowledge and may be carried out only by an approved electrician under consideration of local and national regulations!
SLV Unit E Chiltern Park Boscombe Road, Bedfordshire LU5 4LT
Operating Manual PART B
Trailing Edge Dimmer with DALI Control Input and Push-Function for LED
Lighting 1006452
Read manual carefully and keep for further use!
Safety advices for installation and operation.
Disregard may lead to danger of life, burning or fire! Any works on the
electrical connection only by electrician. Do not alter or modify the product.
Do not open the housing, it protects against touching active parts.
The load of the connected LED lighting may not exceed the maximum load of the
device.
Take out of service when suspecting a defect or malfunction and contact your
dealer or a qualified electrician.
Additional safety advices = Furnishing
Built-in DALI 2 Interface, DALI DT6 Device
Use as directed
This product is suited to control the brightness of LED lighting with an input
power of 100 – 240V AC.
Safety class II (2) – Safety insulated – Connection without protective
conductor.
Do not strain mechanically or expose to strong dirt contamination.
Admissible ambient temperature(ta): -20°C …+50°C.
Admissible load types
| Symbol | Load Type | Max. Load |
|---|---|---|
| Dimmable | 230V: 200W | |
| LED Lamp | 120V: 100W | |
| Dimmable | 230V: 200W | |
| LED Drive | 120V: 100W |
Installation
Switch off mains / fixed connection cable!
The device is suitable for installation in a standard flush-mounted box
(Ø:60mm / min. depth 45 mm).
Access to the built-in product must only be possible via a tool.
Electrical connection
See connection diagrams.
Connection to DALI Fig. A
Connection to a Push-button Fig. B
Equip flexible wire ends with suitable wire ferrules!
Live conductor →Terminal L
Neutral conductor → Terminal N
Operation
DALI
Please read the instruction of the DALI master device to setup the DALI
address.
Push-button Operation A short push switches the light on and off.
A short push changes the brightness.
Settings
Setting and deleting the minimum brightness
Adjust the desired minimum brightness via DALI or push-function.
Push the button “Min. Set” on the device until the LED on the device starts to
flash.
To delete the minimum brightness, adjust the brightness to the highest level
and push the button “Min. Set”. The flashing LED on the device indicates that
the minimum brightness was deleted.
Notice: The dimming range ranges from 1 – 100%. With some load types it
may appear that the connected light flashes at a dimming level of 1%. In such
cases it is recommended to set the minimum brightness above 1%.
© 22.11.2022 SLV GmbH, Daimlerstr.
21-23, 52531 Übach-Palenberg, Germany,
Tel. +49 (0)2451 4833-0. Made in China.
Documents / Resources
|
CONRAD 1006452 Trailing Edge Dimmer with DALI Control Input and Push-Function
for LED
Lighting
[pdf] User Manual
1006452 Trailing Edge Dimmer with DALI Control Input and Push-Function for LED
Lighting, 1006452, Trailing Edge Dimmer with DALI Control Input and Push-
Function for LED Lighting, Trailing Edge Dimmer, Edge Dimmer, Dimmer
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>