goobay 53877 LED Outdoor Floodlight With Motion Sensor User Manual

goodbay LED Outdoor Floodlight With Motion Sensor

Product Information

The product is an outdoor LED light with a motion sensor. It is available in different models with varying specifications. The light source is a non- replaceable SMD 2835 LED. The input voltage
is 220-240V~, 50/60Hz. The light emits neutral white light at a color temperature of 4000K. The product is made of aluminum, tempered glass, metal, and plastic materials. It has an IP44 rating for water and dust resistance.

The product dimensions vary depending on the model:

• 53877: 104 x 68 x 158 mm
• 53878: 130 x 69 x 174 mm
• 53879: 153 x 70 x 191 mm
• 53880: 185 x 70 x 215 mm

The product has a passive infrared (PIR) motion sensor with an adjustable detection range of 1-10 meters. The motion sensor has an ON/OFF switch and can be adjusted for the duration of motion detection (5 seconds to 10 minutes). The product is not dimmable.

Product Usage Instructions

1. Mounting:
   Refer to the provided mounting instructions and diagrams (Fig. 2, Fig. 3, Fig. 4, Fig. 5) for proper installation. Use appropriate mounting materials, which are not included in the package.

2. Connection:
   Follow these steps to connect the product:

   • Ensure the power supply is switched off and disconnected.
   • Remove the cover of the connection block.
   • Strip the insulation of the power supply cable to expose the wires.
   • Connect the wires to the corresponding terminals in the connection block (refer to Fig. 5).
   • Tighten the screws of the connection block to secure the wires.
   • Insert the connector of the M16 cable gland into the LED module’s connection port.
   • Secure the M16 cable gland using a suitable tool.

Settings:
Use the adjustment controls on the product to configure the motion sensor settings:

1. SENS: Adjust the detection range of the PIR sensor from a minimum of 1 meter to a maximum of 10 meters.
2. TIME: Set the duration of motion detection from a minimum of 5 seconds to a maximum of 10 minutes.
3. LUX: Configure the light sensitivity based on ambient light conditions. The light will only turn on in darkness.

Note: Perform a function test after installation and adjust the settings accordingly. The motion sensor has a warm-up phase of approximately 30 seconds before it responds to motion detection.

Maintenance:
The product is maintenance-free. No specific maintenance is required.

Disposal:
Dispose of the product and its packaging in accordance with local regulations. Follow appropriate recycling practices for electronic products.

Safety instructions

The user manual is part of the product and contains important information for correct use.

• Read the user manual completely and carefully before use.

The user manual must be available for uncertainties and passing the product.

• Keep this user manual.

Risk of life by electric shock!
Due to the M16 cable gland, the LED outdoor floodlight is considered installation material and should only be installed, maintained and repaired by qualified electricians. Through improper installation you endanger:

• Your own life
• The life of the users of the electrical system

With an inappropriate installation you risk heavy damages to property, e.g. by fi re. The personal adhesion threatens with damages to property and person for you.

For the installation in particular the following expertise is necessary:

• The appropriate “5 safety rules” : De-energize, secure against restarting, determine Deenergizing, grounding and short circuiting, cover energized neighbouring parts or provide it with barriers

  • selection of the suitable tool, the measuring instruments and if necessary the personal protection equipment
  • evaluation of the measurement results
  • selection of the electricity installation material for the securing of the switching off con-ditions

• IP enclosures

• installation of the electrical installation material

• kind of the supply network (TN-system, IT-system, TT-system) and the electrical opera-ting conditions following from it (classical protective grounding, protective grounding, ne-cessary additional measures, etc.)

• Do not open the housing.

• Do not modify product and accessories.

• Use product, product parts and accessories only in perfect condition.
  The lamps are not replaceable!

• In case of questions, defects, mechanical damage, trouble and other problems, non-recoverable by the documentation, contact your dealer or producer.
  Not meant for children. The product is not a toy!

• Secure packaging, small parts and insulation against accidental use.

• Avoid stresses such as heat and cold, moisture and direct sunlight, microwaves, vibrations and mechanical pressure.

• Follow local installation and building regulations.

• Choose mounting hardware according to the substrate conditions and the product weight.

• Never look directly into the light source.

• Do not aim the beam of the light into the eyes of other persons, animals or reflective surfaces.

The eyes can be damaged.

• Dispose broken glass with suitable protective measures.

Hot surfaces

• Do not touch in or immediately after use.
• Avoid proximity to flammable surfaces.

Heat storage

• Do not cover the product.
• Do not use in sealed environments.

Description and function

Product
Very bright and functional LED outdoor luminaire with motion detector in compact design for house entrances, garages, carports and access paths

• Quick and easy installation thanks to practical M16 cable gland with plug-in function for clamping range/cable diameter 4-10 mm.
• The motion detector can be switched on and off, so it can also be used as a normal out- door spotlight
• Stable, beveled mounting bracket for wall mounting with rotation range of up to 180°.

Scope of delivery

Operating Elements
See Fig. 1

1. Glass pane
2. Reflector
3. LEDs
4. Mounting bracket
5. Housing
6. Locking screw
7. Sensor
8. M16 cable gland
9. Adjustment knob
10. ON – OFF switch sensor

Intended use
This product is intended exclusively for private use and its intended purpose. This product is not intended for commercial use.
We do not permit using the device in other ways like described in chapter “Description or Function“ and „Safety Instructions“. Not attending to these regulations and safety instructions might cause fatal accidents, injuries, and damages to persons and property.

IP 44: This product is protected against splash and contact with foreign objects ≥ Ø1 mm.

Preparation

1. Check the scope of delivery for completeness and integrity.
2. Compare the specifications of all used products.
   These must match or be in the specified range.

Connection and operation

Mounting the LED outdoor floodlight (Fig. 3 – 5)
CAUTION: Danger of falling/crushing.

• Place and use the aids safely.
• Do not hold limbs between shear parts.

1. Select the mounting location according to the following criteria:

   • The surface must be stable.
   • There must be no flammable objects in the vicinity.
   • A distance of 1 m from the illuminating object must be maintained.
   • The product must be mounted absolutely straight.
   • See also fi g. 1 and 3.

2. Select suitable mounting material according to the selected surface and product weight. Mounting material is not included in the scope of delivery.

3. Mark the hole spacing X and the cable entry Y using the mounting bracket and a suitable pin.
   See fi g. 1.

4. Drill the mounting holes with a suitable tool.

5. Fix the LED outdoor floodlight. See Fig. 4.

Fig. 3: Mounting

Fig. 4: Range

Fig. 5: Borehole distance

Connecting the outdoor LED floodlight (Fig. 3)
WARNING: Risk of electric shock

• Have the M16 cable gland connected ONLY by an experienced electrician.

• Observe the safety instructions listed in chapter 1.

• Before working on the product, disconnect the line from the power supply, switch off the fuse and secure it against being switched on again.

• Before working on the product, check and ensure that it is de-energized.

• Ventilation openings must not be in the vicinity.

• Plants, street lights, reflective surfaces or randomly moving objects must not be within the detection range.
  Models without a fitted earthing contact plug must be permanently installed on the mains supply. The power cables used must have a minimum cross-section of 1.0 mm². Stranded wires must be fitted with wire end ferrules.

• Pre-treatment of conductor ends: the length of the exposed ends of the conductors must not exceed 6 mm.

• Fixing method: Fixed in the M16 cable gland.

1. Switch off the fuse and check that there is no voltage.

2. Open the M16 cable gland by turning it anticlockwise until the terminal block is exposed as in fi g. 5.

3. Insulate the cables.
   Slide the parts of the M16 cable gland shown in Fig. 6 over the connection cable.
   Push the cable ends into the corresponding connections of the connector of the M16 cable gland so that the connections of the outdoor LED spotlight (N, L, protective earth/GND ) are connected with the corresponding cable color of the mains connection (N = blue, L = brown, GND = green-yellow). Screw the mains cables tight using a screwdriver as shown in Fig. 6.

4. Insert the plug connector of the M16 cable gland into the connection of the outdoor LED spotlight. The groove on the connector and the pin in the connection provide the correct position.

5. Close the M16 cable gland by turning it clockwise until all parts are firmly connected, as shown in figures. 7 and 8.
   Note: The lamps are not interchangeable!

Settings (Fig. 6)
The LED outdoor floodlight should be mounted at a height of 2.3 – 3 m to function properly. The detection angle of the motion detector is 180°. The LED outdoor floodlight is equipped with a passive infrared sensor (PIR) on which you can make the following settings:

• SENS: Setting the detection range of the PIR sensor between min. 1 m (-) to max. 10 m (+).
• TIME: Sets the switch-off delay of the PIR sensor after detection of a movement between min. 5 seconds (-) and max. 10 minutes (+).
• LUX: Sets from which ambient light the LED outdoor floodlight is active (light sensitivity of the photocell 5 – 2000 lx). Detects ambient brightness in daylight and darkness , and only in darkness .

Fig. 6: Motion sensor settings

Function test:

• Turn the sensor control „SENS“ to the maximum setting „+“.
• Turn the sensor control „TIME“ to the smallest time unit „-“.
• Turn the sensor control „LUX“ to daylight „ „.

This is especially important when testing the motion detector in daylight, otherwise the sensor will not work. After switching on the power supply, the sensor only reacts after a warm-up phase of approx. 30 seconds after a movement has been detected.
There is a switch on the underside of the motion detector that can be used to switch the motion detector on and off. In the „ON“ position, the motion detector is activated. In the „OFF“ position,
the motion detector is deactivated and the LED outdoor floodlight is permanently lit.

Maintenance, Care, Storage and Transportation
The product is maintenance-free.

NOTICE! Material damage

• Regularly check the tightness of product/screws.

• Do not over-tighten the screws.
  Threads can be damaged.

• Only use a dry and soft cloth for cleaning.

• Do not use detergents or chemicals.

• Store the product out the reach of children and in a dry and dust-protected ambience when not in use.

• Store cool and dry.

• Keep and use the original packaging for transport.

Disposal instructions

Product
According to the European WEEE directive, electrical and electronic equipment must not be disposed with consumers waste. Its components must be recycled or disposed apart from each other. Otherwise contaminative and hazardous substances can damage the health and pollute the environment.
As a consumer, you are committed by law to dispose electrical and electronic devices to the producer, the dealer, or public collecting points at the end of the devices lifetime for free. Particulars are regulated in national right. The symbol on the product, in the user manual, or at the packaging alludes to these terms. With this kind of waste separation, application, and waste disposal of used devices you achieve an important share to environmental protection.

WEEE No: 82898622

Specification

Article number| 53877| 53878| 53879| 53880| 53881| 53882| 53883| 53884
---|---|---|---|---|---|---|---|---
Input voltage (V~)| 220-240, 50/60 Hz
Light source| SMD 2835 LED
On-mode power (P on ), W| 10| 20| 30| 50
Standby power (P sb ), in W| 0,29
Useful luminous flux (Φ use) in a wide cone (120°), in lm| 850| 1700| 2550| 4250
Light colour| neutral white
Colour temperature (K)| 4000
Colour rendering index (Ra)| 82| 81| 82| 81
Beam angle (°)| 110| 100
Energy efficiency class| F
L 70 B 50 lifetime (hrs)| 25000
Number of switching cycles| 15000
Dimmability| not dimmable
Start-up time up to 60% light (s)| < 1
Ignition time (s)| < 0.1
Operating temperature (°C)| -25 – + 40
Protection level / Protection class| IP44  / I
Material| aluminium, tempered glass, metal, plastic
Colour| black| white| black| white| black| white| black| white
Dimensions (mm), (W x D X H)| 104 x 68 x 158| 130 x 69 x 174| 153 x 70 x 191| 185 x 70 x 215
Net weight (g)| 286| 385| 567| 765
Installation height (m) from…to| 2.3 – 3
Connection, type| M16 cable gland for clamping area / cable diameter 4–10 mm
Motion sensor Typ| Passive infrared (PIR), with ON / OFF function
Max. detection angle (°)| 180
Detection range (m)| 1 – 10
Light sensitivity range (lx)| 5 – 2000
Switch-off delay range (s)| 5 – 600
Interchangeability of the light source| The light source cannot be replaced.

Goobay®
by Wentronic GmbH | Pillmannstraße 12
38112 Braunschweig | Germany

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>