DDPAI mola N3 Pro Car Dash Cam User Guide

June 12, 2024
DDPAI

DDPAI mola N3 Pro Car Dash Cam

Product Information

  • Product Name: DDPAI MolaN3 Pro 128
  • Built-in GPS Module: Optional

Features:

  • Parking Monitoring Indicator
  • Lens
  • USB Type-C Port
  • Working Indicator
  • MIC
  • Reset Button
  • Mounting Bracket
  • Speaker
  • Lock Button
  • Micro SD Card Slot

Address: Floor 12F, Yihua Finance Building, Nanshan District, Shenzhen

FCC Compliance Statement:
This device complies with Part 15 of the FCC Rules. The operation must meet the following two conditions:

  1. This device may not cause harmful interference.
  2. This device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

RF Warning Statement:
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure condition without restriction.

FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.

WEEE Notice:
This product must not be disposed of or dumped with your other household waste. You are liable to dispose of all your electronic or electrical waste equipment by relocating over to the specified collection point for recycling of such hazardous waste. Isolated collection and proper recovery of your electronic and electrical waste are required.

RoHS Compliance:
This product is in compliance with Directive 2011/65/EU of the European Parliament and of the Council of 8 June 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment.

For Products That Include Batteries:
Instructions for Users on Removal, Recycling and Disposal of Used Batteries:
To remove the batteries from your equipment or remote control, reverse the procedure described in the owner’s manual for inserting batteries. For products with a built-in battery that lasts for the lifetime of the product, removal may not be possible for the user. In this case, recycling or recovery centers handle the dismantling of the product and the removal of the battery.
In case of batteries, accumulators, and button cells containing more than 0.0005% mercury, more than 0.002% cadmium, or more than 0.004% lead, shall be marked with the chemical symbol for the metal concerned: Hg, Cd, or Pb respectively.

CAUTION:
[Additional caution information is missing from the provided text.]

Product Usage Instructions

To use the DDPAI MolaN3 Pro 128, follow these steps:

  1. Ensure that the device is connected to a power source.
  2. Insert a micro SD card into the designated micro SD card slot.
  3. If available, connect the built-in GPS module to the device using the USB Type-C port.
  4. Mount the device using the provided mounting bracket.
  5. Press the lock button to secure the device in place.
  6. Press the reset button to reset the device if needed.
  7. Observe the working indicator to check the device’s status.
  8. Use the lens to capture videos or images as desired.
  9. If necessary, listen to audio playback using the built-in speaker.
  10. Monitor parking using the parking monitoring indicator.

For more detailed instructions on specific functions and features, please refer to the owner’s manual provided with the product.

GPS AND SR

The GPS can synchronize the driving trajectory and various GPS-related parameters on the DDPAI APP of a mobile phone, including GPS positioning and GPS track recording. The SR can import the GPS data and sensor data into the video to generate an exclusive, cool trajectory interface, giving you a better visual and content sharing experience. NOTE: The GPS version of the Dash Cam supports GPS and SR. The normal version of the Dash Cam doesn’t support GPS and SR.

SPECIFICATIONS

  • Product Name: Dash Cam
  • Model:22nola?N Pro
  • Input: 5V … 2A
  • Size: 993628mm
  • Storage: Class 10 TF card up to 128GB, loop recording
  • GPS: Built-in2CPS?module (optional)

PACKAGE CONTENTS

PRODUCT OVERVIEW

DDPAI-mola-N3-Pro-Car-Dash-Cam-2

DDPAI-mola-N3-Pro-Car-Dash-Cam-3

LED INDICATOR INSTRUCTION

DDPAI-mola-N3-Pro-Car-Dash-Cam-4

INSTALLATION

  1. Clean an area on the windshield where you wish the Dash Cam to be installed, this assists in adhesion.

  2. Take out the Dash Cam and bracket from the box, push the lock button on the bracket, and insert the USB Type-C port of the bracket into the USB Type-C port of the Dash Cam to ensure that the bracket fits firmly.

  3. Remove the protective film from the back of the bracket, attach the adhesive side of the bracket on the windshield where it has an unobstructed view of the road but does not interfere with the driver’s view. As shown below.
    DDPAI-mola-N3-Pro-Car-Dash-Cam-6

  4. Use the installation tool to lift the edges of the windshield/molding and tuck in the power cable. Connect the Dash Cam to the car charger (plugged into cigarette lighter socket) and power cable. Power traces/ Ideal mount area
    DDPAI-mola-N3-Pro-Car-Dash-Cam-7

  5. Turn on the Dash Cam after installation, you will hear a boot tone, and a blue light flashes slowly.

  6. Connect the DDPAI App, refer to the reference line on the preview interface, and rotate the bracket to adjust the camera angle.

APP INSTRUCTION

Install DDPAI APP Scan the QR code to download the “DDPai” APP. iOS Android

Pair Smart Phone to Dash Cam

  1. Keep the Dash Cam and mobile phone within 2.5meters.
  2. Launch DDPAI App, tap on “Device > Connect new devices”.
  3. Choose your DDPAI Dash Cam from the network list(For Android system, App will start to search Dash Cam network automatically. For iOS phone: turn on WLAN from “Settings -›WLAN”). The Dash Cam’s default SSID (or Wi-Fi name) is DDPAI_mola N3 Pro_XXXX.
  4. Enter the password (the default password is ‘1234567890’). .Enter DDPA| App, wait a few seconds until the preview screen show.

DDPAI-mola-N3-Pro-Car-Dash-Cam-9

Preview

  1. Open the DDPAI App, and add your Dash Cam.
  2. Select “Device > Entering” tab, this will bring you to the preview page. entering
    DDPAI-mola-N3-Pro-Car-Dash-Cam-10

Rotate your smart phone or press expand ¿ icon, turn the preview screen to landscape mode.

Playback
Tap and left/right drag timeline bar at the screen bottom to create the starting point of the recording you wish to preview, then tap on thumbnail when you have made your selection, or wait for 5 sec for buffering, now you can watch the history recording.

Download Video Files

  1. Tap and left/right drag timeline bar at the screen bottom to create the starting point of the recording you wish to download, then tap on thumbnail when you have made your selection, or wait for 5 sec for buffering, to enter the download start screen.
  2. Tap on from preview screen to enter the download interface.
  3. After the video has finished downloading, click ‘Complete”.

CONTACT
en.ddpai.com
feedback@ddpai.com
AB DDPAI Technology Co., Ltd )
Floor 12F, Yihua Finance Building, Nanshan District, Shenzhen

For more information and FAQs, Please scan the QR code:

FCC statement

This device complies with Part 15 of the FCC Rules. operation must meet the following two conditions:

  1. This device may not cause harmful interference.
  2. This device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Relocate or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

RF warning statement:
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

WEEE Notice

The Directive on Waste Electrical and Electronic Equipment (WEEE) , which entered into force as European law on 14/02/2014, resulted in a major change in the treatment of electrical equipment at end-of-life.
The purpose of this Directive is, as a first priority, the prevention of WEEE, and in addition, to promote the reuse, recycling and other forms of recovery of such wastes so as to reduce disposal. The WEEE logo on the product or on its box indicating collection for electrical and electronic equipment consists of the crossed-out wheeled bin, as shown below.
This product must not be disposed of or dumped with your other household waste. You are liable to dispose of all your electronic or electrical waste equipment by relocating over to the specified collection point for recycling of such hazardous waste. isolated collection and proper recovery of your electronic and electrical waste equipment at the time of disposal will allow us to help conserving natural resources. Moreover, proper recycling of the electronic and electrical waste equipment will ensure safety of human health and environment. For more information about electronic and electrical waste equipment disposal, recovery, and collection points, please contact your local city center, household waste disposal service, shop from where you purchased the equipment, or manufacturer of the equipment.

RoHS Compliance
This product is in compliance with Directive 2011/65/EU of the European Parliament and of the Council of 8 June 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment.

For Products That Include Batteries
EU Batteries Directive 2013/56/EU
A new battery directive 2013/56/EU on Battery and Accumulator replacing directive entered into force on the 1/07/2015. The directive applies to all types of batteries and accumulators (AA, AAA, button cells, lead acid, rechargeable packs) including those incorporated into appliances except for military, medical and power tool applications.
The directive sets out rules for collection, treatment, recycling and disposal of batteries, and aims to prohibit certain hazardous substances and to improve environmental performance of batteries and all operators in the supply chain.

Instructions for Users on Removal, Recycling and Disposal of Used Batteries
To remove the batteries from your equipment or remote control, reverse the procedure described in the owner’s manual for inserting batteries.
For products with a built-in battery that lasts for the lifetime of the product, removal may not be possible for the user. In this case, recycling or recovery centers handle the dismantling of the product and the removal of the battery. If ,for any reason, it becomes necessary to replace such a battery, this procedure must be performed by authorized service centers.
In the European Union and other locations, it is illegal to dispose of any battery with household trash. All batteries must be disposed of in an environmentally sound manner. Contact your local waste-management officials for information regarding the environmentally sound collection, recycling and disposal of used batteries.

WARNING: Danger of explosion if battery is incorrectly replaced. To reduce risk of fire or burns, don’t disassemble, crush, puncture, short external contacts, expose to temperature above 60°C (140°F), or dispose of in fire or water. Replace only with specified batteries. The symbol indicating ‘separate collection ‘for all batteries and accumulators shall be the crossed- out wheeled bin shown below:
In case of batteries, accumulators and button cells containing more than 0.0005 % mercury, more than 0. 002 % cadmium or more than 0. 004 % lead, shall
be marked with the chemical symbol for the metal concerned: Hg, Cd or Pb respectively. Please Refer to the below symbol:

CAUTION

  • The product’s optimal temperature range is -20°C — 70°C.
  • Install the device near the rear-view mirror to obtain the best open-field view. Do NOT install the Dash Cam in a location that will obstruct your required driving view.
  • Dash Cam with built-in eMMC card: Featuring high efficiency, stability and durable. The dash cam should be formatted via App or PC regularly to extend its lifespan.
  • Dash Cam with external memory card: Support brand Class 10 micro SD card up to 128GB Max. The dash cam should be formatted before using and it can be formatted via App or PC regularly to extend its lifespan.
  • Do not use any cardboard, paper towel, or napkins to clean the lens.
  • Do not attempt to repair, dismantle, or modify the Dash Camera hardware by yourself.
  • Do not install the product in an environment with high humidity, or combustible gases or liquids.
  • Drawings for illustration purpose only. Actual product may vary due to product enhancement.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals