ROPOX Bluetooth FlexiElectric and Upper Cabinets User Guide

ROPOX Bluetooth FlexiElectric and Upper Cabinets

Product Information

The Ropox Bluetooth is a device that allows you to remotely control Ropox products using your iOS device. By connecting your iOS device to a Bluetooth adapter inserted into a Ropox product, you can adjust the product upwards or downwards. The Ropox Connect App is the application used for controlling the Ropox products.

The Ropox Bluetooth is compatible with FlexiElectric Diagonal and VertiElectric VertiInside products.

Product Usage Instructions

How to download the App
For iOS:

1. Scan the QR code or open the App Store.
2. In the App Store, press ‘Search’.
3. Search for “Ropox Connect”.
4. Find the Ropox Connect App and press ‘Get’ to download it.

Setup
To connect to a Ropox product and start remote control:

1. Insert the Bluetooth adapter into the Ropox product following the provided instructions.
2. Pair your iOS device with the Ropox product by following the pairing process.

Using the Ropox Connect App
Once the pairing is completed, you can use the Ropox Connect App to remotely control the product from a distance. The control range is typically greater than 10 meters.

Drive the product
To adjust the product upwards or downwards:

1. Open the Ropox Connect App on your iOS device.
2. Select the connected Ropox product.
3. Use the up or down button to control the height of the product.

Show height
To view the current height of the product:

1. Open the Ropox Connect App on your iOS device.
2. Select the connected Ropox product.
3. The displayed height will show the current position of the product.

Save height
To save a specific height setting for easy access:

1. Open the Ropox Connect App on your iOS device.
2. Select the connected Ropox product.
3. Name the product and press ‘Save’. The height setting is now saved.

Troubleshooting
If you encounter any issues, refer to the following troubleshooting steps:

Cannot find the correct product

1. In the list of Bluetooth devices, look for devices starting with “LogicLink”.

Cannot connect to the product
If you are unable to establish a connection with the product:

1. Ensure that the Bluetooth adapter is properly inserted into the Ropox product.
2. Check if the product is within range of your iOS device.
3. Restart your iOS device and try again.

Safety Precautions
Follow all safety guidelines provided in the user manual to ensure safe and proper usage of the Ropox Bluetooth and associated Ropox products.

Introduction

The Ropox Connect App is an application which allows you to remotely control your Ropox products. By connecting your iOS device to a Bluetooth adapter inserted into a Ropox product, you gain the ability to adjust your product upwards or downwards.
After pairing of an iOS device and a Ropox product has been completed, you’re able to remotely control the product from great distance. In practice, this oftentimes is greater than 10 meters. Additionally, the application allows you to save height settings, to enable you to easily change between pre-set heights.

How to download the App

For iOS

1. Scan the QR code or open the app: App Store.
2. In the App Store, press ‘Search’.
3. Search for ”Ropox Connect”.
4. Find the Ropox Connect App, and press ‘Get’.

Compatible products and functions

Setup

To connect to a Ropox product is quick and easy. Before your Ropox product can be remotely controlled, the Bluetooth adapter must be inserted into the product. To insert the Bluetooth adapter into your Ropox product, follow the instructions below.
When finding the correct Bluetooth device in the app, look for a device named LogicLink. Note, the Bluetooth adapter has two buttons on the front, allowing you to adjust the product in height, other than with the button that came with your Ropox product.

1. Determine the placement of the adapter, then grab the Bluetooth adapter and the split-cable
   

2. Insert the split-cable in the plug ”HS” in the control box. Then, insert the adapter in one end of the split-cable, and the button that came with the product, in the other

3. If the adapter is to be fixed, it should be done now*. Use the drilling-template for this, as seen on the next page
   

4. Put the adapter into ”Pairing-mode”. This is done by pressing twice on the small button in the back

Note! It is recommended, when multiple products need to be connected, that 1 adapter is inserted at a time, and then saved

Drilling-template
For screw-mounting the Bluetooth adapter on a hardened surface, it’s recommended to use the adapter as a drilling template. Mark out the three points, pre-drill, then mount the adapter. Screws are not included. For mounting, cable ties or double-adhesive tape can also be used. Measurements of the adapter can be seen below.
*Write down the pairing code from the back of the adapter before mounting!

Instructions for use

Saving a product

1. Open the app Ropox Connect.

2. From the main menu, press the red button.
   

3. The app will locate all nearby Bluetooth devices in range. Choose the product you wish to save.
   

4. Name your product and press save. The product has now been saved.
   
   Note! When first connecting to the product, the adapter will request a pairing code. This is listed on the back of the adapter. Usually, this code is: 000000

Drive a saved product

1. From the main menu, press on a saved product.
   

2. The first time a product is connected to, you’re asked to measure and set a bottom height of the product. This is optional.
   

3. Whether or not the bottom height has been set, the product can be driven with the /▼ button, either upwards or downwards.
   
   Note! When using the Ropox Connect app with certain products, including Vision and VertiInside, the height-display and saved settings-display will be disabled. Tilt on Vision is also disabled.
   The display will instead show:
   

Saving a height setting

1. From the main menu, press on a saved product.
   

2. Drive the product to the desired height.
   

3. Press save setting. Name the height setting and press save once again.

Drive with a saved height setting

1. From the tab ’Saved settings’, press a saved setting.
   

2. A press button is shown. Hold down the button until you’ve reached your saved setting.
   

3. When the product has reached its saved setting, it’ll stop driving.

Settings

Remove a product or setting

1. Press and hold and drag the product or setting to the left.
   

2.  Press the red icon and hit ‘Delete’. This will remove the product or saved setting.

Accessibility settings

Adjust the text size

1. To adjust the text size, go to your device’s settings.
2. From settings, scroll down and go to ‘Display & Brightness’.
3. Scroll down and go to ’Text Size’.
4. Adjust, with the slider, your device’s text size.

Haptic feedback
The Ropox Connect App will, as standard, provide haptic feedback in the form of vibration, when it drives a Ropox product. This can be disabled or enabled from the device’s settings.

Screen reader
Ropox Connect App is compatible with the screen reader, which can be enabled from the device’s settings.

1. Go to your device’s settings and scroll down to ‘Accessibility’.
2. From ’Accessibility’, press ’VoiceOver’.
3. From ’VoiceOver’, press the topmost slider to enable the screen reader.

Note! Adjusting your device’s accessibility settings will change the settings on the entire device, not just the app!

Troubleshooting

Can’t find the product in the App

1. After pressing the red button from the main menu, look for LogicLink.
2. If there is no LogicLink on the list, the Bluetooth adapter must reinitiate pairing-mode. This is done by pressing the small button on the back of the adapter twice.
3. The product needs a reset. Read the user manual that came with the Ropox product, to learn of this procedure. Use the button that came with the product.
   A reset procedure is driving the product to its highest or lowest height, and then hold down the button in that direction for a few seconds.

Can’t connect to the product

1. Double click the button on the back, to put the adapter into pairing mode, then attempt to reconnect.

Product doesn’t drive
If the app finds the product, but won’t drive, it might be because the Bluetooth adapter has lost connection to the product. This can happen if a reset is done with the app.

1. Unplug the adapter cable from the split cable, then reconnect it.
2. Try and drive the product again.

Languages

The Ropox Connect app a variety of languages. A list of supported languages:

• English (GB/US)
• Danish (Danmark)
• Norwegian (Norge)
• Finnish (Suomi)
• German (Deutschland)
• Dutch (Nederland)
• Spanish (España)
• Italian (Italia)
• French (France)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>