ROPOX FlexiElectric Corner Wall Mounted Corner Frame Instruction Manual

June 9, 2024
ROPOX

ROPOX FlexiElectric Corner Wall Mounted Corner Frame Instruction

ROPOX FlexiElectric Corner Wall Mounted Corner Frame Instruction
Product

Introduction

Planning, installation, and normal use must only be carried out if the FlexiElectric Manual is used in combination with these Mounting Instructions. All other information, including the use and technical data, will be found in the FlexiElectric Manual.

Producer:

Instruction

ROPOX FlexiElectric Corner Wall Mounted Corner Frame Instruction
\(1\)

  1. Slide the first leg onto one of the aluminum profiles and pass the hexagonal shaft through the hole of the leg. Tighten the screws lightly.ROPOX FlexiElectric Corner Wall Mounted Corner Frame Instruction \(2\)
  2. Slide the bracket into the aluminum profile. MUST be placed over the leg. Tighten the screws lightly.ROPOX FlexiElectric Corner Wall Mounted Corner Frame Instruction \(3\)
  3. Slide the nut of the motor fixture into the aluminum profile on the underside and guide the hexagonal shaft through the motor. Tighten the screws lightly.ROPOX FlexiElectric Corner Wall Mounted Corner Frame Instruction \(4\)
  4. Place the motor beside the leg and tighten the screw lightly.ROPOX FlexiElectric Corner Wall Mounted Corner Frame Instruction \(5\)
  5. Slide the next leg into the aluminum profile. Tighten the screws lightly.ROPOX FlexiElectric Corner Wall Mounted Corner Frame Instruction \(6\)
  6. Place the next bracket over the second leg. If extra brackets are required between the two brackets shown here, they must be mounted first. Tighten the screws lightly.
  7. Slide the two nuts of the angular fitting into the aluminum profile.!! Tighten the screws lightly.!!
  8. Slide the nut of the angular gear casing into the aluminum profile. Important!! See that the gear is placed as illustrated!! Place the hexagonal shaft in the gear casing. Tighten the screws lightly.ROPOX FlexiElectric Corner Wall Mounted Corner Frame Instruction \(9\)
  9. Now assemble the other side following the same procedure. Don’t tighten the screws till the whole frame has been assembled. Place the leg.ROPOX FlexiElectric Corner Wall Mounted Corner Frame Instruction \(10\)
  10. Place the bracket.ROPOX FlexiElectric Corner Wall Mounted Corner Frame Instruction \(11\)
  11. Place the motor.ROPOX FlexiElectric Corner Wall Mounted Corner Frame Instruction \(12\)
  12. Place the leg.ROPOX FlexiElectric Corner Wall Mounted Corner Frame Instruction \(13\)
  13. Place the outermost bracket.ROPOX FlexiElectric Corner Wall Mounted Corner Frame Instruction \(14\)
  14. Now assemble the two frames in the angular fitting. See that both hexagonal shafts have been pressed home in the gear casing.
  15. Place the aluminum profiles so that they are flush in the corner.
  16. Tighten the four screws of the angular fitting and one screw of the gear casing fitting.ROPOX FlexiElectric Corner Wall Mounted Corner Frame Instruction \(17\)
  17. Mount the assembly fitting on the two brackets in the corner of the frame. Move the legs from side to side until the brackets fit as illustrated. Tighten the two screws.ROPOX FlexiElectric Corner Wall Mounted Corner Frame Instruction \(18\)
  18. Tighten the two screws.ROPOX FlexiElectric Corner Wall Mounted Corner Frame Instruction \(19\)
  19. When all legs and brackets have been aligned and placed in the required position, tighten all screws!ROPOX FlexiElectric Corner Wall Mounted Corner Frame Instruction \(20\)
  20. If the support arm isn’t level but points upwards, this can be rectified by mounting included angle between the support arm and the aluminum profile!

Before use follow the instructions in the FlexiElectric User Manual!

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals