TheUMS AIM24-SB Radar Sensor User Manual
- June 17, 2024
- TheUMS
Table of Contents
TheUMS AIM24-SB Radar Sensor
Product Introduction
This product 2BB56AIM24-SB is a module for object(motion) detection sensor using a frequency band of 24GHz.
Electrical Characteristics
[Table 2] Electrical characteristics Electrical Characteristics: Unless otherwise noted,
All parameters apply at VDD = 5.0V, VSS = GND, TA = +25℃
Parameter| Sym.| Min| Typ| Max| units| Condition
Operating Frequency| OFrq| 24.05| 24.15| 24.25| GHz|
Supply Voltage| VDD| 3.6| 5.0| 5.5| V|
Supply current| Icc| 13| 45| 50| mA|
Operating Temperature| TO| -40| 25| 85| ℃|
S_OUT Voltage| OVGPIO_ABS| -0.5| 3.3| 3.3| V|
S_Out Current| OIGPIO_ABS| -25| | 25| mA|
Detection distance| | | | | |
Dd| | 7| 10| m| AIM24-SB
Detection field
(Beam Width)
| | | | | |
| | | |
Detection field
(Beam Width)
| E| | 109| | °|
AIM24-SB
H| | 40| | °
Start-up Time| | | 1| | Sec| Wake up time from power-on
Response Time| | –| 20| | mSec| Continuous Sensing
RF Characteristics
Electrical Characteristics
The following power system diagram shows the set of power supply pins as implemented for the AIM24-SB. The VCC pin must be bypassed to ground via an external capacitor (1μF; X5R ceramic or better) and must not be connected to anything else.
Package Dimensions
[Figure 4] AIM-12QUAD type
List of applicable FCC rules
This module has been granted modular approval as below listed FCC rule parts.
FCC Rule parts 15C (15.249)
FCC Statement
FCC Compliance Statement
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC Interference Statement
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
FCC Caution Statement
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate this equipment. This
transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
FCC Radiation Exposure Statement
This equipment should be installed and operated with a minimum distance of
20cm between the radiator and your body.
RF exposure considerations
RF exposure statements
This Transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.This equipment complies with FCC RF radiation
exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with a minimum distance of 20 centimeters
between the radiator and your body or nearby persons.
Label and compliance information
The module is labeled with its own FCC ID Certification Number. If the FCC ID
Certification Number is not visible when the module is installed inside
another device, then the outside of the device into which the module is
installed must also display a label referring to the enclosed module. Contains
FCC ID: 2BB56AIM24-SB
Information on test modes and additional testing requirements
Operation Frequency: 24.05 GHz ~ 24.25 GHz
- FCC – Max tune-up Power : 7 dBm
- CE – Max tune-up Power : 4.97 dBm
CE RED_EU declaration
This product can be used in which EU members, in accordance with Article
10(10) / or this product can be used in at least one EU country, in accordance
with Article 10(2) The module is only modular FCC certified, guiding
manufacturers of the host product to comply with Part 15 Subpart B when
applying the module. Therefore, it is important to know that additional tests
in compliance with Part 15 Subpart B are required.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>