ROPOX 4SingleManual Electric Height Adjustment 65-95 cm User Manual
- June 9, 2024
- ROPOX
Table of Contents
ROPOX 4SingleManual Electric Height Adjustment 65-95 cm
Introduction
4Single is a multi-function table, which may be adjusted to suit seated or standing activities. Owing to the unique design there are a variety of applications and the table is therefore also ideal for wheelchair users. This document must ALWAYS accompany the product and be read by and available to users.
All users must follow these instructions. It is very important that the instructions have been read and understood prior to the operation of the product. These instructions must always be available to the user and must accompany the product in case of relocation. Correct use, operation and inspection are decisive factors for efficient and safe performance. The operation must be made or supervised by an experienced adult, who has read and understood the importance of section 8 ” Safety in use”
Application
4Single is designed to obtain optimum working height for the user. It is an activity table and not for use as a lifting table or person lifter. The product must be used indoor, under room temperatures and humidity as stated in section 3. 4Single is not designed for use in damp rooms.
Conformity with EU Directive and UK Directive This product has CE marking and is thus in accordance with the basic requirements concerning functionality and safety of the current EU Directive. See separate CE declaration. This product has UKCA marking. See separate Declaration of Conformity
Technical data
- Product: 4SingleManual
- Item numbers: Set of legs, manual
- Height 55-85cm / 21,6 – 33,4in H1 50-41110
- Height 65-95cm / 25,6 – 37,4 in H2 50-41210
- Front fascias for frame L = xxx cm 50-42xxx
- From 60-300cm in increments of 1cm
- From 23,6-118,1in in increments of 0,4in
- Side fascias for frame W = xxx cm 50-44xxx
- From 60-200cm in increments of 1cm
- From 23,6-78,7in in increments of 0,4in
- Options: Wheels: Increase the table height by 6.5cm / 2.5in
- Material: Welded steel tubes St. 37 and various plastic components
- Surface treatment: Blue chromate, powder coating: Standard CWS 81283 RAL 7021 mat
- Max. load of frame: 150kg / 330lb evenly distributed
- Temperature: 5-45° C
- Air humidity: 5-85% (non-condensing)
- Complaints: See page 12
- Producer: Ropox A/S, DK-4700 Naestved, Tel.: +45 55 75 05 00 E-mail: info@ropox.dk – www.ropox.com
Schematic diagram of frame
All connections to the table must be flexible to ensure that the table moves freely within the range of adjustment.
For table top length 60 – 300cm / 23.6 – 118.1in (Length of frame always 0.4cm/0,2 less than the table top, i.e. 59.6 – 299.6cm / 23.4 – 117.9in)
- Height: 55-85cm (H1) 21,6-33,4in
- Height: 65-95cm (H2) 25,6 – 37,4in
- Height w/wheels: + 6.5cm/2,5in
- Size of frame without middle support: Length 60-300cm / 23,6 – 118,1in Width 60-120cm / 23,6 – 47,2in
- Size of frame with middle support: Length 60-300cm / 23,6 – 118,1in Width 121-200cm / 47,6 – 78,7in
Component/Item No./ Pcs.
- Gearbox 96000656 2
- Shaft adapter, outside Hex7, inside Hex6 30*12999-047 4
- Side fascia shaft, Hex6. Length = frame width – 13.8cm/5,4in 2
- Gearbox for the crank handle, Fixture & Bushing 30*12999-148 1
- Front fascia shaft, Hex7. Length = frame length – 7cm/6,5in 1
- Leg 1 2
- Leg 2 2
- Handle 20*60320-297 1
- Allen screw M8x16 95010003 16
- Side fascia profile, Length = frame width – 4cm/4,9in 2
- Front fascia profile, Length = frame length – 4cm/4,9in 2
- Stop ring screw 98000-555 2
- Screw ø4.8×13, Torx 95091012 2
- Cover plate 50*40000-025 4
Mounting instructions, illustrations
Mounting must always be carried out by competent personnel. Prior to mounting, check that all parts have been provided. See list of components, section 6.
Assembly of frame
-
Check that the height (L) of all four legs is identical. May be adjusted on hexagonal shaft by means of the open-end wrench provided. Place side fascias on a plane surface and mount legs. See label on legs.
-
At the opposite end of the handle fit a stop ring on either side of the angular gear. Do not tighten the stop rings till the frame has been assembled.
-
Now mount the two front fascias. Tighten the bolts securely by means of the wrench provided.
-
Place the frame on the table top and push the cover plates between legs and table top. Centre the frame in relation to the tabletop.
-
Fix the table top with screws through the holes of the fascias.
Mounting of wheels (option) -
Mount the wheels. Do not forget to fit three washers on each wheel.
List of components
- Set of legs H1, 50-41110:
- Set of legs H2, 50-41210:
- Front fascias for L=xxx cm, 50-42xxx: Shaft Hex7 (fascia length – approx. 5cm/2in)
- Side fascias for W=xxx cm, 50-44xxx: Shaft Hex6 (fascia width + ca.2.5cm/1in)
- Handle for 4Single 50-47010-9:
- Gearbox 96000656:
- *Shaft adapter 3012999-047:**
- *Gearbox for handle 3012999-148:**
- The Gearbox contains:
- Gearbox 96000688
- Gearbox 96000688
- Bushing 30*12999-052
- Allen screw M8x16 95010003:
- Screw ø4.8×13 95091012:
- *Stop ring incl. screw 3065500-084:**
Options
- Brake wheels, black (4 wheels) 50-41600: Increase the table height by 6.5 cm2,5in 1 set incl. 12 washers (95170510)
Safety in use
-
4Single must only be used by persons, who have read and understood these instructions.
4Single is an activity table and should not be used as a lifting table or person lifter, -
Always use the table in a manner excluding the risk of damage to persons or property. The person operating the table is responsible for avoiding damage or injury.
-
Children or persons with reduced observation capability should only operate the table when supervised.
-
If the table is used in publicly accessible locations where children or persons with reduced observation capability may get near the table, the person operating the table must pay attention to those present in order to prevent dangerous situations.
-
Make sure that there is free space above and below the table to allow height adjustment.
-
Do not operate the table in case of defects or damage.
-
Do not overload the table and make sure that the load distribution is correct.
-
Do not use the table in an explosive environment.
-
In connection with inspections, service or repairs always remove weight from the table.
-
Modifications, which may influence the operation or construction of the table, are not allowed.
-
Installation, service and repairs must be carried out by competent personnel.
-
If the table has not been assembled according to these mounting instructions the right to complain may become void.
-
Only use Ropox original spare parts as replacement parts. If other spare parts are used, the right to complain may become void.
Cleaning/ maintenance
Cleaning of frame Cleans the frame with a wrung cloth with lukewarm water and a mild detergent. Do not use enchants or abrasives or grinding cloths, brushes or sponges. Dry the frame after cleaning.
Maintenance
Inspections, service and repairs must be carried out by competent personnel. The frame is maintenance-free and the moving parts have been lubricated for life.
For reasons of safety and reliability, we recommend inspection of the frame once a year:
- Check that all bolts have been securely tightened.
- Check that the table moves freely from bottom to top position.
After each inspection, fill in the service schedule. Only use Ropox original spare parts for the replacement of parts. If other spare parts are used, the right to complain may become
Service schedule, operation, and maintenance void.
Complaints
See General Terms of Sale and Delivery on www.ropox.com
- ROPOX A/S Ringstedgade 221 DK – 4700 Naestved
- Tel.: +45 55 75 05 00
- Fax.: +45 55 75 05 50
- E-mail: info@ropox.dk www.ropox.com