ROPOX FlexiManual Corner Wall Mounted Corner Frame User Manual

June 9, 2024
ROPOX

ROPOX FlexiManual Corner Wall Mounted Corner Frame -

FlexiManual Corner
Mounting Instructions, Supplement to FlexiManual User Manual

Introduction

Planning, installation and normal use must only be carried out if the FlexiManual User Manual is used in combination with these Mounting Instructions.
All other information, including use and technical data will be found in the FlexiManual User Manual.
Producer:
Ropox A/S, DK-4700 Naestved, Tel.: +45 55 75 05 00
E-mail: info@ropox.dk, www.ropox.com

– Slide the first leg onto one of the the aluminium profiles and pass the hexagonal shaft through the hole of the leg. Tighten the screws lightly.

ROPOX FlexiManual Corner Wall Mounted Corner Frame -
leg– Slide the bracket into the aluminiumprofile. MUST be placed over the leg. Tighten the screws lightly.

ROPOX FlexiManual Corner Wall Mounted Corner Frame
-screws
– Slide the nut of the fitting for the handcrank into the aluminium profile on the front and pass the hexagonal shaft through the gear casing. Tighten the screws lightly.

ROPOX FlexiManual Corner Wall Mounted Corner Frame -
screws1

– Slide the next leg into the aluminium profile. Tighten the screws lightly.

ROPOX FlexiManual Corner Wall Mounted Corner Frame -screws
1

– Place the next bracket over the second leg. If extra brackets are required between the two brackets shown here, they must be mounted first. Tighten the screws lightly.

ROPOX FlexiManual Corner Wall Mounted Corner Frame
-brackets

– Slide the two nuts of the angular fitting into the aluminium profile. !! Tighten the screws lightly.!!

– Side the nut of the angular gear casing into the aluminium profile. Important!! See that the gear is placed as illustrated.!! Pass the hexagonal shaft into the gear casing. Tighten the screws lightly.

ROPOX FlexiManual Corner Wall Mounted Corner Frame -
fitting1

– Now assemble the other side following the same procedure. Place the legs. Tighten the screws lightly.

ROPOX FlexiManual Corner Wall Mounted Corner Frame
-fitting2
– Slide the bracket into the aluminium profile. MUST be placed over the leg. Tighten the screws lightly.

ROPOX FlexiManual Corner Wall Mounted Corner Frame
-fitting3– Slide the next leg into the aluminium profile. Tighten the screws lightly.

ROPOX FlexiManual Corner Wall Mounted Corner Frame
-fitting4
– Place the next bracket over the second leg. If extra brackets are required between the two brackets shown here, they must be mounted first. Tighten the screws lightly.

ROPOX FlexiManual Corner Wall Mounted Corner Frame
-fitting6– Now assembly the two frames in the angular fitting. See that both hexagonal shafts have been pressed home in the gear casing.

ROPOX FlexiManual Corner Wall Mounted Corner Frame
-fitting7– Place the aluminium profiles to that they are flush in the corner.

ROPOX FlexiManual Corner Wall Mounted Corner Frame
-fitting9
– Tighten the four screws of the angular fitting and one screw of the gear casing fitting.

ROPOX FlexiManual Corner Wall Mounted Corner Frame
-fitting10– Mount the assembly fitting on the two brackets in the corner of the frame. Move the legs from side to side till the brackets fit as shown. Tighten the two screws.

ROPOX FlexiManual Corner Wall Mounted Corner Frame
-fitting12

– Tighten the two screws.

ROPOX FlexiManual Corner Wall Mounted Corner Frame
-fitting13

– When all legs and brackets have been aligned and placed in the required position, tighten all screws!

ROPOX FlexiManual Corner Wall Mounted Corner Frame
-fitting14Before use follow the instructions of the FlexiManual User Manual!

ROPOX A/S
Ringstedgade 221
DK – 4700 Naestved
Tel.: +45 55 75 05 00 Fax.: +45 55 75 05 50
E-mail: info@ropox.dk
www.ropox.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals