SEALEY SC01.V2 4 SHELF 2 DOOR FLOOR CABINET User Guide
- June 4, 2024
- SEALEY
Table of Contents
SEALEY SC01.V2 4 SHELF 2 DOOR FLOOR CABINET
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
SAFETY
-
WARNING! Ensure Health and Safety, local authority and general workshop practice regulations are adhered to when using this cabinet.
-
WARNING! Use caution when handling and assembling the metal components. The metal may have sharp edges or corners, the use of protective gloves is recommended.
✔ Locate cabinet in a suitable working area and secure to a wall with suitable fasteners.
✔ Keep the work area clean and uncluttered.
✔ Keep the cabinet clean and tidy in accordance with good workshop practice.
✔ Keep children and unauthorised persons away from the working area.
✘ DO NOT climb, step or stand on the cabinet shelves.
✘ DO NOT use the cabinet for any purpose other than that for which it is designed.
✘ DO NOT use in damp work areas. -
WARNING! The warnings, cautions and instructions referred to in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood that common sense and caution are factors which cannot be built into this product, but must be applied by the operator.
INTRODUCTION
Featuring two large doors, four shelves and base storage. Added security provided by cylinder lock, supplied with two keys. All steel construction, stabilized by an inner cross member. Supplied flat-packed to save freight cost, simple assembly required.
SPECIFICATION
Model No: ……………………………………………………….SC01.V2
Overall Size (W x D x H): ………………….900 x 400 x 1800mm
CONTENTS
A1 x1………………………………………………Back (left hand side)
A2 x1…………………………………………… Back (right hand side)
B1 x1……………………………………………… Side (left hand side)
B2 x1……………………………………………. Side (right hand side)
C x1……. …………………………………………………Cross member
D x1…….. ……………………………………………………………..Base
E x1…………………………………………………….Base outer fascia
F x1……………………………………………………………………… Top
G x4……. ………………………………………………………………Shelf
H1 x1…… ………………………………………..Door (left hand side)
H2 x1…… ………………………………………Door (right hand side)
I x4……………………………………………….. Bolt and butterfly nut
J x2……… ……………………………. Top panel retainer moulding.
K x4……………………………………………….Hinge pivot moulding
L x2……… …………………………….Locking rod recess moulding
P x4…….. ……………………………………………………….Hinge pin
Q x4…….. ………………………………………… Door stop moulding
S x16……………………………………………………………. Shelf stop
ASSEMBLY
BACK ASSEMBLY (Step 1)
Place the back panels (A 1& A2) on a suitably protected flat surface to
prevent scratching.
Interlock the tabs into the slots on the back panels and slide together until
the two panels are fully engaged and aligned.
SIDE ASSEMBLY (Step 2)
Hold the side panels (B1 & B2) at a slight angle and fit the tabs on the back
panels into the slots of the side panels and slide up to engage.
CROSS MEMBER ASSEMBLY (Step 3)
Tie the side panels together at the bottom front edge by attaching the cross
member (C) using four bolts (I) and four butterfly nuts as shown in the inset
diagram above.
BASE ASSEMBLY (Step 4)
Place the base (D) into position as shown above and slide it down to the
bottom until its edges make contact with the receiving channels on the back
and side panels. Using a rubber hammer, tap the base down until it is fully
engaged in the channels.
TOP ASSEMBLY (Step 5)
Take the two top panel retainer mouldings (J) and fully insert one into each
hole at the top front edge of each side panel in the orientation shown in Step
5.
Take the top panel (F) and hook it’s front edge over the two retainer
mouldings, then swing the panel downwards until the top edges of the back and
side panels begin to enter the receiving channels within the top panel. Tap
the top panel down into position using a rubber hammer until the four indents
in the back panels clip into the matching holes in the back receiving
channels.
BASE OUTER FASCIA ASSEMBLY (Step 6)
Fit the base outer fascia (E) over the cross member (C) with the hinge pivot
holes facing upwards. Tap the base outer fascia down with a rubber hammer
until the indents in the sides of the fascia clip into the matching holes on
the cross member (C).
Insert a hinge pivot moulding (K) at each end of the Upper face of the base
outer fascia (E). Insert the other two hinge Pivot mouldings at each end of
the downward facing edge of the cabinet top.
Insert a locking rod recess moulding (L) into the centrally placed holes in
the same faces used for mounting the hinge pivot mouldings at both the top and
the bottom.
MAINTENANCE
Using a mild solution of detergent and water and wipe the unit down with a soft cloth.
SHELF ASSEMBLY (Step 7)
Insert shelf stops (S) at the desired height for each shelf and lay the
shelves onto the stops.
DOORS ASSEMBLY (Step 8)
Mount each door in turn by placing it between the upper and lower hinge pivot
mouldings. Align the upper hole in the door edge with the hole in the upper
pivot moulding and insert a hinge pin upwards through the door and into the
moulding. Rotate the short arm of the pin around onto the inner face of the
door as shown above and bend over the metal tab to retain it. Mount the lower
hinge pin in the same way. Repeat the process to mount the other door.
Fit the rubber door stops (Q) as shown in Step 8 to the corners of each door.
| ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools,
accessories and packaging should be sorted, taken to a recycling centre and
disposed of in a manner which is compatible with the environment. When the
product becomes completely unserviceable and requires disposal, drain any
fluids (if applicable) into approved containers and dispose of the product and
fluids according to local regulations.
---|---
Note: It is our policy to continually improve products and as such we
reserve the right to alter data, specifications and component parts without
prior notice. Please note that other versions of this product are available.
If you require documentation for alternative versions, please email or call
our technical team on technical@sealey.co.uk or 01284 757505.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is
required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk.
IP32 7AR
01284 757500
01284 703534
sales@sealey.co.uk
www.sealey.co.uk
Documents / Resources
|
SEALEY SC01.V2 4 SHELF 2 DOOR FLOOR
CABINET
[pdf] User Guide
SC01.V2, 2 DOOR CABINET, FLOOR CABINET, CABINET
---|---
|
SEALEY SC01.V2 4 Shelf 2 Door Floor
Cabinet
[pdf] User Manual
SC01.V2 4 Shelf 2 Door Floor Cabinet, SC01.V2, 4 Shelf 2 Door Floor Cabinet, 2
Door Floor Cabinet, Door Floor Cabinet, Floor Cabinet
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>