CONRAD 2619567 Monocrystalline Solar Module Instruction Manual

CONRAD 2619567 Monocrystalline Solar Module

Technical Data

How to use

1. Plan the installation position, place the solar panel on the installation area, and fix the solar panel with screws so that it will not shake. Start the wires connection after solar panel is fixed. Then start the series or parallel connection of solar panels according to power demand.
   

2. Select the suitable output interface according to your needs.
   

Delivery content

• Solar module
• Operation instruction

Explanation of symbols

The lightning symbol inside a triangle is used when there is a potential risk of personal injury, such as electric shock.

An exclamation mark in a triangle indicates important instructions in this operating manual that absolutely have to be observed.

Safety instructions

Read the operating instructions carefully and especially observe the safety information. If you do not follow the safety instructions and information on proper handling in this manual, we assume no liability for any resulting personal injury or damage to property. Such cases will invalidate the warranty/guarantee.

• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may become dangerous playing material for children.
• Protect the product from extreme temperatures, strong jolts, high humidity, moisture, flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and protect it from any accidental use. Safe operation can no longer be guaranteed if the product:
  • is visibly damaged,
  • is no longer working properly,
  • has been stored for extended periods in poor ambient conditions or
  • has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height can damage the product.
• Also observe the safety and operating instructions of any other devices which are connected to the product.
• The solar module’s performance can vary depending on weather conditions. Keep this in mind when operating a device with this product.
• Do not touch the terminal points during operation.
• Use suitable extension cables and adaptor plugs approved for outside operation . Do not use bare wires or other uninsulated objects to connect the product.
• Always ensure correct polarity when connecting a device.
• Avoid direct contact with the surface. The surface is sensitive and can be easily scratched or destroyed through contamination.
• Solar module may only be used in a temperate climate. The solar module is a device which is not secured against explosions. Thus, it may not be installed in the vicinity of highly inflammable gases and vapours.
• If this solar module is used in a system consisting of multiple solar modules, all modules used must have the same amperage. Only solar modules with identical amperage may be used when connected in series. Only solar modules with identica voltage may be used when connected in parallel.
• Consult an expert when in doubt about operation, safety or connection of the device.
• Maintenance, modifications and repairs are to be performed exclusively by an expert.

Attention and cleaning

Regularly clean the solar module, as its performance would otherwise decrease and the surface could be irreversibly damaged.

• Please read the user guide before using this product.
• The solar panel will generate voltage when it was exposed in the sun, so please avoid installing the solar system in the sun. If it must be installed in the sun, insulation protection is required.
• Before assembling, pay attention to the positive and negative signs, the positive and negative poles cannot be reversed.
• Do not step on, or disassemble the solar panel.
• Do not place the solar panel in shading places such as trees and buildings.
• Do not soak the solar panel in water or any other liquid.
• Do not use or store solar panels near open flames or flammable materials.
• Do not scratch the solar panel with sharp objects.
• Do not put corrosive substances on the solar panel.
• When using the solar panel the circuit must be correctly connected to the equipment and check the connection status of each component each wire and plug.
• Due to the material characteristics of the product it is strictly forbidden to drop it, otherwise it will cause the internal damage of the solar panel and make the product unusable.
• Use a soft brush or damp cloth to clean the dust on the surface of the product If there is bird droppings or other sticky objects on the surface of the product it should be cleaned up immediately.
• What should I do if there is no output from the solar panel?
  • Please put the solar panel in a sunny environment and check the connection status of each component, each wire and plug. You can try to replace the data cable or charging device to check whether the solar panel is working

Disposal

Electronic devices are recyclable waste and must not be disposed of in the householdwaste.At the end of its service life, dispose of the product according to the relevant statutoryregulations.You thus fulfil your statutory obligations and contribute to the protection of the environment.

Distributed by Conrad Electronic SE, Klaus-Conrad-Str. 1D-92240 Hirschau

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>