SUNRICHER 0-10V BLE Ceiling Mounted PIR Sensor Controller Owner’s Manual
- June 12, 2024
- SUNRICHER
Table of Contents
0-10V BLE Ceiling Mounted
**PIR Sensor Controller
Product Datasheet
Please read all instructions before installation
**
Product info
Parameters
Input | Output, 0/1-10V | Control | Environment | Others |
---|---|---|---|---|
Power | Signal | Current | Dimming Curve | Dimming Method |
Relative humidity | Size | |||
12-24VDC | Bluetooth | Max. 20mA | Logarithmic | PWM |
dimensions
Features
- 0-10V BLE ceiling mounted sensor controller, Bluetooth® mesh network
- PIR sensing with daylight haversting function
- Built-in 20mA 0-10V signal output
- Mesh network, which has a much longer control distance, transmits received signals to neighboring devices
- All devices on 0-10V line are broadcast controlled by mobile application
- Supporting our kinetic energy switches and EnOcean switches EWSSB and EWSDB
- In typical indoor environment, the range for wireless communication is 20m to 25m . Actual range is dependent on field installation.
- On-board antenna
- Available with Magnetic reset (Touch the top part of sensor for 5 seconds)
- Waterproof grade: IP20
- 5 years warranty
Dimension
Application
Specifications
ENERGY SAVINGS
- Low/High-end trimming
- Daylight harvesting
- Occupancy/Vacancy detection
- Auto and advanced demand response programs
- Time-of-Day dimming schedule
- Energy monitoring
SENSING
- Testing height: 2.5m
- Detection area diameter: 8m @ 2.5m height
COMFORT & CONVENIENCE
- Advanced occupancy detections
- Light-level stability
- Configurable dim-and-linger occupancy
- Personalized setting profile
- Work with kinetic switch keypad and dimmer wallstation
- Multi-scenes control
ENVIRONMENT AND APPROBATION
- Operating temperature: 0°C to 45°C
- Agency approbations: UL Listed /FCC/ RoHS/ BQB…
- Warranty: 5 years
Detection Pattern
Warning
- DO NOT install with power applied to device
- DO NOT expose the device to moisture
Operation
- Do wiring according to connection diagram
- Kindly refer to for further pairing Silvair commissioning User Manual
- Press and hold down the “Reset” button on the controller over 5 seconds until the indicator flashes , which means it has been reset .
- Available with Magnetic reset (Touch the top part of sensor for 5 seconds)
Wiring
Statement
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment o ffand
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
IC STATEMENT
This device complies with Industry Canada’s licence-exempt RSSs. Operation is
subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may
cause undesired operation of the device.
Update log
Date | Version | Update content | Update by |
---|---|---|---|
2022-11-12 | V1.5 | FCC/IC Update | Romeo |
Subject to change without notice.Please contact us if you have any question.
Technology Partner
www.sunricher.com