VISUAL COMFORT CHO 2551 Fresno Large 3 4 Gas Wall Lantern Instruction Manual
- June 12, 2024
- VISUAL COMFORT
Table of Contents
VISUAL COMFORT CHO 2551 Fresno Large 3 4 Gas Wall Lantern
Product Information
Fresno Large 3/4 Gas Wall Lantern
Item #: CHO 2551
Manufacturer : Visual Comfort
This Fresno Large 3/4 Gas Wall Lantern is a light fixture designed to be mounted on a wall. It should be installed in accordance with all applicable local installation codes and by a familiar with its construction and operation. The lantern comes with additional hardware, including 3/8 gas adapters and an additional 1/4 flare nut fitting.
Assembly Instructions
- Carefully remove all parts from the box and place them on a clean, soft surface.
- Remove the mounting plate (C) from the fixture (E) by removing screws (F).
- Use the mounting plate (C) as a guide to mark the location for mounting hardware.
Lighting Your Lantern
- Before turning on the gas supply to the lantern, turn the valve (A) to the off position.
- Open the door of the lantern and allow it to completely air out.
- With a lighter or flame above the burner tip (B), press in and turn the valve (A) counter-clockwise approximately 30 degrees until the flame appears
- Adjust the flame to the desired height. Note: Do not operate the fixture with the gas valve fully open or with a flame height greater than 3.
Maintenance
Before every use, check the following:
- Keep the area around the lantern clear and free from combustible materials, gasoline, and other flammable vapors and liquids.
- Check the burner area to ensure the flow of gas or combustion is never obstructed.
- Always ensure proper ventilation before use.
Care Instructions
- Allow the lantern to cool completely before cleaning.
- Use a feather duster or a soft cloth to clean the surface of the lantern.
- Use a damp towel to clean the glass of the lantern.
- Do not use abrasives or chemical agents for cleaning.
ASSEMBLY INSTRUCTIONS
Fresno Large 3/4 Gas Wall Lantern
Item # CHO 2551
FOR YOUR SAFETY:
DANGER
FIRE OR EXPLOSION HAZARD If you smell gas:
- Shut off gas to the appliance.
- Extinguish any open flame.
- If odor continues, leave the area immediately..
- After leaving the area, call your gas supplier or fire department.
- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
- Fixtures must be installed at least 3″ from combustible walls and 12″ from combustible ceilings.
- Installation must conform with local codes or, in the absence of local codes, the National Fuel Gas Code, ANSI Z223.1.
Failure to follow these instructions could result in fire or explosion, which
could cause property damage, personal injury, or death.
Save these instructions for future reference.
Please contact support@visualcomfort.com
for additional information on obtaining replacement parts..
NOTICE:
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction and
operation of it, as well as the hazards involved. Inspect item and contents
carefully. If any damage or defect is found, do not install. Retain all
packaging material until installation is complete and approved.
TOOLS REQUIRED
(NOT INCLUDED):
- Phillips Screwdriver
- Pencil
- Slotted Screwdriver
- Hammer
- Drill
-
Carefully remove all parts from the box. Place on a clean, soft surface.
-
Remove mounting plate (C) from fixture (E) by removing screws (F).
-
Using mounting plate (C) as a guide, mark mounting hardware positions and follow mounting hardware instructions to secure mounting plate to wall surface.
Note: Due to various mounting surface types, mounting hardware is not included. Please select proper hardware based on surface application. -
Open fixture door (I), then install glass parts (H) to fixture (E) and secure by bending metal tabs.
-
Install glass part (G) to door (I) and secure by bending metal tabs, then close the door.
-
Connect gas tubing (D) from lantern to gas source using proper connection method.
Note: If gas tubing cannot be connected behind back plate, remove grommet from bottom of back plate for alternate exit location. See diagram 1. -
Install fixture (E) to mounting plate (C) and secure with screws (F).
-
Double check gas connections and test for leaks before attempting to light lantern.
ADDITIONAL HARDWARE INCLUDED
For your convenience, 3/8” gas adapters and additional 1/4″ flare nut fitting included inside box. Discard if not required.
NOTICE:
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction and
operation of it, as well as the hazards involved. Inspect item and contents
carefully. If any damage or defect is found, do not install. Retain all
packaging material until installation is complete and approved.
- Turn valve (A) to off position before turning on gas supply to lantern. See diagram 2.
- Open door and allow to completely air out.
- With lighter/flame above the burner tip (B), press in and turn valve (A) counter-clockwise approximately 30 degrees until flame appears. See diagram 3.
- Adjust flame to desired height.
Note: Do not operate fixture with gas valve fully open or flame height greater than 3”.
MAINTENANCE: CHECK BEFORE EVERY USE
- Keep appliance area clear and free from combustible materials, gasoline and other flammable vapors and liquids.
- Check burner area to ensure flow of gas or combustion is never obstructed.
- Always ensure proper ventilation before use.
CARE INSTRUCTION
-
Allow for item to cool completely before cleaning.
-
Use feather duster or soft cloth to clean surface.
-
Use damp towel to clean glass.
-
No abrasives or chemical agents