legrand ENP4260-NA Plastic 42 IN Cover W Instruction Manual
- June 12, 2024
- Legrand
Table of Contents
legrand ENP4260-NA Plastic 42 IN Cover W
Product Information
The product is a series of surface-mount and recessed-mount enclosures
available in different sizes: 20 inches (50.8cm), 30 inches (76.2cm), and 42
inches (106.7cm). The specific models are
ENP2050-NA, ENP3050-NA, ENP4250-NA, ENP2060-NA, ENP3060-NA, ENP4260-NA,
ENP2080-NA, ENP3080-NA, and ENP4280-NA. The product comes with installation
instructions and important safety instructions.
Product Usage Instructions
-
Surface Mounting:
To mount the enclosure on a surface:
Use a plywood backboard and align the pre-drilled mounting
holes on the rear of the enclosure.
It is recommended to use a level for correct installation. -
Recessed Mounting:
To recess-mount the enclosure:
Use the provided mounting tabs on the sides of the enclosure to secure it to wall studs.
It is recommended to use a level for correct installation. -
Running Power to the Enclosure:
To run power to the enclosure:
Install a single-gang metal outlet box.
Connect a 15 amp, 120 volt power receptacle to the power cable using an approved wiring method according to local codes.
Note: Legrand offers both non-surge protected (F7526) and surge protected (364569-02-V1) outlet kits. -
Trim Ring Assembly:
To assemble the trim ring:
Align the edges of two trim pieces and push them together until you hear a click, indicating the locking tab has engaged.
Fit the remaining pieces together to complete the assembly. -
Affix Trim Ring to Enclosure or Wall:
To affix the trim ring:
Using the included screws, affix the trim ring to the
corresponding holes located in the enclosure frame (4a).
If desired, the trim ring can be affixed directly to wall studs (4b). -
Attach Door to Trim Ring:
To attach the door:
Starting with the top hinge location, align the door hinge to the trim ring and push until you hear a click indicating the hinge is connected.
Fit the remaining door and trim hinges together to complete the installation. -
Locking the Door:
To lock the enclosure door:
The enclosure door can lock to the trim ring by applying the provided Phillips head screws to the holes located on the top and bottom corners of the door. A keyed lock is optional (364478-01).
Note:
For specific replacement trim ring kits for the 20-inch (50.8cm) model, use
ENP2001-NA.
Catalog Number(s)
Country of Origin: Made in USA
ENP2050-NA 20” (50.8cm)
ENP3050-NA 30″ (76.2cm)
ENP4250-NA 42″ (106.7cm)
| 20″ / 30″ / 42” Plastic Enclosure with Hinged Door and Trim Ring|
INSTALLATION INSTRUCTIONS – Please read these instructions completely before you begin
---|---|---
ENP2060-NA 20” (50.8cm)
ENP3060-NA 30″ (76.2cm)
ENP4260-NA 42″ (106.7cm)
| 20″ / 30″ / 42” Plastic Door and Trim Ring, Only
ENP2080-NA 20” (50.8cm)
ENP3080-NA 30″ (76.2cm)
ENP4280-NA 42″ (106.7cm)
| 20″ / 30″ / 42” Plastic Enclosure, Only
IMPORTANT SAFETY INSTRUCTIONS
- Do not use this product near water; such as a bath tub, wash bowl, kitchen sink, laundry tub, swimming pool, or in a wet basement.
- Never push objects of any kind into this product through openings, as they may touch dangerous voltages. Never touch uninsulated telephone wires or terminals, unless the telephone line has been disconnected at the network interface.
- Never install communications wiring, or components, during a lightning storm.
- Equipment shall be installed in accordance with ANSI/NFPA 70, National Electrical Code (NEC), NFPA 72, CAN-ULC-S540, Canadian Electrical Code, and/or other applicable sections of ANSI/IEEE C2 & National Electrical Safety Code (NESC). Equipment intended for installation in information technology equipment (computer) rooms should be installed in accordance with NFPA 75, Standard for the Fire Protection of Information Technology Equipment.
- Power supplied to fire or burglary components must be provided by UL Listed Class 2 fire / burglary power limited power supply.
- All power limited and non-power limited wiring must be separated by a minimum of ¼” spacing.
- Installation shall be completed by a professional electrical contractor or low voltage technician.
- Maximum load carrying capacity of 30 lb.
** These enclosures are only compatible with subassembly components as described in the individual subassembly’s installation instructions.
Tools Required
- Enclosure Physical Installation
Locate enclosure indoors in a low humidity, climate controlled (0°C / 32°F – 49°C / 120°F) area. Remove cable and receptacle knockouts as needed. When required, 2″ rubber grommets (AC1034) are available for the top facing 2″ cable knockouts.
Surface Mounting
Mount to a plywood backboard using the pre-drilled mounting holes on the rear
of the enclosure. The use of a level is recommended for correct installation
of the enclosure.
Recessed Mounting
Use provided mounting tabs on the sides of the enclosure to secure to wall
studs. The use of a level is recommended for correct installation of the
enclosure.
Running Power to the Enclosure
Install a single-gang metal outlet box. Connect 15 amp, 120 volt power
receptacle to power cable with approved wiring method to local codes.
NOTE: Legrand offers both non-surge protected (F7526) and surge protected (364569-02-V1) outlet kits.
Trim Ring Assembly
Align the edges of two trim pieces and push them together until you hear a
“CLICK”, indicating the locking tab has engaged. Fit remaining pieces together
to complete assembly.
Top View – Preassembly
Underside View – Assembled
Affix Trim Ring to Enclosure or Wall
Using the included screws, affix the Trim Ring to the corresponding holes
located in the enclosure frame (4a).
If desired, the Trim Ring can be affixed directly to wall studs (4b).
Attach Door to Trim Ring
Starting with the top hinge location, align the door hinge to the trim ring
and push until you hear a “CLICK” indicating the hinge is connected. Fit
remaining door and trim hinges together to complete installation.
Locking the Door
The enclosure door can lock to the trim ring by applying the provided Phillips
head screws to the holes located on the top and bottom corners of the door.
A keyed lock is optional (364478-01).
ENP2001-NA 20” (50.8cm)
20″ Replacement Trim Ring Kit
ENP3001-NA 30” (76.2cm)
30″ Replacement Trim Ring Kit
ENP4201-NA 42” (106.68cm)
42″ Replacement Trim Ring Kit
Replacement Trim Kits
In the event a provided Trim Ring becomes lost or damaged, Legrand offers a
replacement kit for 20”, 30” and 42” sizes. Alignment of Trim Ring shown
below:
No: 1507319 Rev. D
© Copyright 2019 Legrand All Rights Reserved.
800.321.2343. 1.877.BY.LEGRAND
www.legrand.us
www.legrand.ca
References
- Legrand CA | Delivering and Managing Power, Light, and Data
- Legrand US | Delivering and Managing Power, Light, and Data
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>