ORTUR Laser Master 2-S2 Laser Engraver Instruction Manual

June 12, 2024
ORTUR

ORTUR-LOGO

ORTUR Laser Master 2-S2 Laser Engraver

ORTUR-Laser-Master 2-S2-Laser-Engraver-product

PRODUCT INFORMATION

MODEL NO. LASER MASTER 2- 52 v,.2ORTUR-Laser-Master 2-S2-Laser-Engraver-
fig-1

SAFETY INSTRUCTIONS

Safety instructions when using the laser engraver

  1. The laser engraver could generate laser light. It is strictly forbidden to place any living body under the laser emission port (this port is marked with a yellow warning sign).
  2. Patients with photosensitive epilepsy are prohibited from using or approaching this laser device.
  3. When using the laser engraving machine, the operator and anyone near the machine must wear laser safety glasses. Do not operate the laser without eye protection (laser goggles). Our machines come with a pair of safety goggles, but additional laser safety glasses can be purchased commercially. Requirements for goggles: wavelength protection 400-445nm (+-Snm), outer diameter +5, minimum L-level LS.
  4. When the laser engraving is working, the operator must pay close attention and not place it alone to prevent the engraved material from catching fire. Please set up the laser engraver in a fireproof area to ensure good ventilation. If possible, we recommend that you purchase a fire extinguisher and keep it close to the machine.
  5. Use the laser engraver in a room that can be closed by a door, making sure that neither the laser beam nor stray light can penetrate the window.
  6. When using the laser engraving, use the door sign or the warning light on the door to indicate that the laser engraving is running.
  7. Make sure there is no flammable material near the laser engraving, we recommend using a fireproof mat as a working surf ace.
  8. Ensure adequate ventilation when operating the laser engraving. Engraving certain materials may generate fumes, which should be exhausted using a dedicated filtered exhaust.
  9. When the machine is running, do not touch the laser beam or touch it with other objects, which may cause serious bodily injury or beam reflection. Do not touch the radiator, you may burn your body and hands when the laser engraver just stops working.
  10. Do not let children or teenagers use the laser engraving alone (especially children under the age of 14), adult supervision is required at all times.
  11. For commercial use, use and registration with regulatory bodies and professional associations is mandatory.
  12. The operating temperature range of the machine is -5°C-50°C.

Packing List

ORTUR-Laser-Master 2-S2-Laser-Engraver-
fig-2

Option 1: LU2-2 Laser Module

ORTUR-Laser-Master 2-S2-Laser-Engraver-
fig-3

Option 2: LU2-4-SF Laser Module

Option 3: LU2-4-LF Laser Module

ORTUR-Laser-Master 2-S2-Laser-Engraver-
fig-5

INSTALLATION

ORTUR-Laser-Master 2-S2-Laser-Engraver-
fig-6 ORTUR-Laser-Master 2-S2-Laser-Engraver-
fig-7 ORTUR-Laser-Master 2-S2-Laser-Engraver-
fig-8 ORTUR-Laser-Master 2-S2-Laser-Engraver-
fig-9 ORTUR-Laser-Master 2-S2-Laser-Engraver-
fig-10

Option 1: LU2-2 Laser ModuleORTUR-Laser-Master 2-S2-Laser-Engraver-
fig-11

Option 2 : LU2-4-SF Laser ModuleORTUR-Laser-Master 2-S2-Laser-Engraver-
fig-12

Option 3 : LU2-4-LF Laser ModuleORTUR-Laser-Master 2-S2-Laser-Engraver-
fig-13

Customer Support
Youtube outer
Instagram
Twitter
Tutorials olm2s2
Feedback
Facebook
Facebook-group

Dongguan Ortur Intelligent Technologies Co., Ltd. Address: No. 1 Building, Ruijin Science and Technology Industrial Park, Changping, Dongguan 523558, Guangdong, China

MADE IN CHINA

LaserGRBL: How to turn off the setting of “Auto power off after half an hour of standby”?

  1. Power on, open LaserGRBL to connect the machine.
  2. Click the “Grbl Configuration”.
  3. Change the “Value” of the “$263” line to 0 and click “Write” to save, the setting to automatically turn off the machine after half an hour of standby will be turned off. Change the “Value” of the “$263” line to 30 and click “Write” to save, the setting to automatically turn off the machine after half an hour of standby will be turned on.ORTUR-Laser-Master-2-Pro-S2-Laser-Engraver-FIG-20

LightBurn: How to turn off the setting of “Auto power off after half an hour of standby”?

  1. Power on, open LightBurnto connect the machine. Enter “$263=0” in the “blue frame”, and “Enter” to confirm.
  2. If you want to open the settings, please enter “$263=30”. “OK” appears, indicating that the setting of automatic shutdown after standby for half an hour has been turned off.ORTUR-Laser-Master 2-S2-Laser-Engraver-fig-18

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals