ORTUR Laser Master 2 Pro S2 Laser Engraver User Manual
- June 12, 2024
- ORTUR
Table of Contents
ORTUR Laser Master 2 Pro S2 Laser Engraver **
**
PRODUCT INFORMATION
LASER MASTER 2 PRO 52
SAFETY INSTRUCTIONS
Safety instructions when using the laser engraver
- The laser engraver could generate laser light. It is strictly forbidden to place any living body under the laser emission port (this port is marked with a yellow warning sign).
- Patients with photosensitive epilepsy are prohibited from using or approaching this laser device.
- When using the laser engraving machine, the operator and anyone near the machine must wear laser safety glasses. Do not operate the laser without eye protection (laser goggles). Our machines come with a pair of safety goggles, but additional laser safety glasses can be purchased commercially. Requirements for goggles: wavelength protection 400-445nm (+-Snm), outer diameter +5, minimum L-level LS.
- When the laser engraving is working, the operator must pay close attention and not place it alone to prevent the engraved material from catching fire. Please set up the laser engraver in a fireproof area to ensure good ventilation. If possible, we recommend that you purchase a fire extinguisher and keep it close to the machine.
- Use the laser engraver in a room that can be closed by a door, making sure that neither the laser beam nor stray light can penetrate the window.
- When using the laser engraving, use the door sign or the warning light on the door to indicate that the laser engraving is running.
- Make sure there is no flammable material near the laser engraving, we recommend using a fireproof mat as a working surface.
- Ensure adequate ventilation when operating the laser engraving. Engraving certain materials may generate fumes, which should be exhausted using a dedicated filtered exhaust.
- When the machine is running, do not touch the laser beam or touch it with other objects, which may cause serious bodily injury or beam reflection. Do not touch the radiator, you may burn your body and hands when the laser engraver just stops working.
- Do not let children or teenagers use the laser engraving alone (especially children under the age of 14), adult supervision is required at all times.
- For commercial use, use and registration with regulatory bodies and professional associations is mandatory.
- The operating temperature range of the machine is -5°C-50°C.
- The flame sensor is provided to keep our equipment as safe as possible and no warranty, written or implied, is made as to the availability or functionality of the flame sensor.
Features
- Ortur Laser Master 2 Pro is a upgraded model of Laser Master 2, which is a worldwide popular desktop laser engraver in 2020, well-known as its user-friendly experience, safe features and stable quality.
- Laser Master 2 Pro is armed with the OLM-PRO-V10 Motherboard, the 3rd generation laser motherboard, has more features, it supports flame detector, emergency stop button, and Ortur Offline Controller.
- There is a G-sensor on the motherboard for active position protection. If the machine detects unauthorized movement, the laser beam will stop.
- Laser Beam Safety Guard, if your computer system halted or USB cable disconnected, led to that the laser engraver stop moving, the laser beam will stop, to prevent fire.
- Exposure Duration Detection and Limitation, when the laser engraver is working, if the motor don’t move, this extra safety function would turn off the laser to prevent fire.
- Ortur Laser 1.5 Firmware has optimized the motion algorithm to support the faster speed engraving from 4000mm/min to 9000mm/min.
- The laser module comes with a adjustable safety cover, which can be adjusted up and down according to requirements.
- Mechanical Structure has been improved based on laser master 2, so as to support the faster speed carving / long-time working, its strong and durable.
REQUIRED TOOLS
INSTALLATION
CONNECTING WIRES
Optional Parts Z-axis Lifting Device
HOW TO FIX SCREWS
When Z-axis Lifting Device assembled, the mismatch of increased weight and acceleration may affect movement accuracy. Then, you need to adjust the firmware parameters according to the following instructions.
Optional Parts Offline Controller
REQUIRED TOOLS
- It’s optional, you could buy it separately, and use this auxiliary device to work with Laser Master 2 Pro for engraving cylindrical objects.
- It’s optional, you could buy it separately, to build Laser Master 2 Pro to be an enclosed laser engraver with an exhaust system for fumes that would make the users safer to use on more materials and limit eye exposure to the laser.
Customer Support
Youtube_ortur
Instagram
Twitter
Tutorials_olm2pros2
Feedback
Facebook
Facebook-group
MADE IN CHINA
Dongguan Ortur Intelligent Technologies Co., Ltd. Address: No. 1 Building, Ruijin Science and Technology Industrial Park, Changping, Dongguan 523558, Guangdong, China
LaserGRBL : How to turn off the setting of “Auto power off after half an hour of standby”?
- Power on, and open LaserGRBL to connect the machine.
- Click the”Grbl Configuration”.
- Change the “Value” of the “$263” line to 0 and click “Write” to save, the setting to automatically turn off the machine after half an hour of standby will be turned off. Change the “Value” of the “$263” line to 30 and click “Write” to save, the setting to automatically turn off the machine after half an hour of standby will be turned on.
LightBurn: How to turn off the setting of “Auto power off after half an hour of standby”?
- Power on, open LightBurnto connect the machine. Enter “$263=0” in the “blue frame”, and “Enter” to confirm. If you want to open the settings, please enter “$263=30”.
- “OK” appears, indicating that the setting of automatic shutdown after standby for half an hour has been turned off.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>