Sunricher DT8 DALI Dual Color Touch Controller Instruction Manual
- June 12, 2024
- SUNRICHER
Table of Contents
DT8 DALI Dual Color Touch Controller
Important: Read All Instructions Prior
to Installation
Function introduction
Product Data
| Output Signal | DALI signal |
|---|---|
| Power Supply | 12-24VDC |
| Power consumption | < 20 mA |
| DALI consumption | 4 mA |
| Operating temperature | 0-40°C |
| Relative humidity | 8% to 80% |
| Dimensions | 86x86x29.1mm |
- Touch sensitive.
- Glass interface (white & black).
- Comply to DALI standard protocol IEC 62386-102, IEC 62386-207, IEC 62386-209 and in compliance with DALI products from other international incorporation
- Enable to control 1 DALI Group and 4 DALI Scenes.
- Enable to set start DALI group number (0-15) and scene number (0-15) by rotary switches on the back.
- Support DT8 devices
- Color temperature adjustment according to DALI specifications of Device Type 8, Color Type Tc.
- Each DT8 device is controlled via a single DALI address
Safety & Warnings
- DO NOT install with power applied to device.
- DO NOT expose the device to moisture.
Wiring diagram
Operation
- Set starting Group number via rotary switch on the back: (0-15 selectable)
• This DALI touch panel controller enables dimming commands and DT8 commands to be sent to 1 Group of devices on the DALI circuit. A rotary switch on the back is used to select Groups you would like to control and set the starting Group number, and total 16 Groups (0-15) can be selected.
• When the rotary switch arrow position is at 0, the panel controls all DALI devices on the circuit via broadcast.
• When the rotary switch arrow position is at X except 0 (1-15), the panel controls DALI Group X-1.
Note: all DALI slaves on the circuit shall be assigned to one or more DALI groups by DALI master first.
Please refer to the detailed Group setting table as follows:
| Rotary Switch Position | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12 | 13 | 14 | 15 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| DALI Group Selected | Broadcast | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12 | 13 |
14
2. Set starting Scene number via rotary switch on the back: (0-15 selectable)
• This DALI touch panel controller enables Scene selection commands for up to
4 Scenes to be sent to the DALI circuit. A rotary switch on the back is used
to select Scenes you would like to control and set the starting scene number,
and total 16 Scenes (0-15) can be selected.
• When the rotary switch arrow position is at X (0-15), Scene button S1
controls Scene X, S2 controls Scene X+1, S3 controls Scene X+2, and S4
controls Scene X+3.
Please refer to the detailed Scene setting table as follows:
| Rotary Switch Position | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12 | 13 | 14 | 15 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Scene assigned to Si | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12 | 13 | 14 | 15 |
| Scene assigned to S2 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12 | 13 | 14 | 15 | 0 |
| Scene assigned to S3 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12 | 13 | 14 | 15 | 0 | 1 |
| Scene assigned to S4 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12 | 13 | 14 | 15 | 0 | 1 | 2 |
Installation
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>