NINGBO DD7006 Connector Bridge User Guide
- June 12, 2024
- Ningbo
Table of Contents
NINGBO DD7006 Connector Bridge
Product Information
The product is a Poe (Power over Ethernet) device with the following specifications:
- Input Voltage: 42V-57V
- Input Current: 1.6A-1.3A
- Operating Temperature: -5°C to 50°C
This device complies with part 15 of the FCC Rules, which ensures that it meets the necessary standards for electromagnetic interference. It operates under the following conditions:
- The device must not cause harmful interference.
- The device must accept any interference received, including interference that may cause undesired operation.
FCC RF Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. To ensure safe usage, it is recommended to install and operate the equipment with a minimum distance of 20cm between the radiator and your body.
Product Usage Instructions
Follow these instructions to use the product:
- Ensure that the input voltage supplied to the device is within the range of 42V-57V.
- Connect the device to the appropriate power source using a compatible PoE power supply.
- Make sure the operating temperature is within the range of -5°C to 50°C. Avoid exposing the device to extreme temperatures outside this range.
- To comply with FCC regulations, ensure that the device does not cause harmful interference. If interference is experienced, try adjusting the positioning or distance from other devices.
- If the device receives interference that causes undesired operation, it should still function properly. However, try to minimize the potential sources of interference or consult the manufacturer for further assistance.
- To comply with FCC RF radiation exposure limits, maintain a minimum distance of 20cm between the radiator of the device and your body during installation and operation.
Caution
- Stay clear of concrete walls or corners
- Keep away from electric appliances
Connector Bridge allows user to link their motorized shutters, blinds, and
curtains to the Internet via Wi-Fi or Ethernet, enabling control via smart APP
and interaction with other loT products.
INSTRUCTION
-
Step 1 Download APP
Please scan below QR code.
-
Step 2
Please scan below QR code to learn more about link upConnector Bridge with home router, setup Connector APP, and establishing a connection with other loT applications.
Program / Pairing:
Press and hold the program button for about 2 seconds, then release it until
the LED blinks purple.
Reset:
Press and hold the program button for about 10 seconds, then release it until
the LED blinks red.
Product Parameter
Indoor use only
- Internet 2.4G Wi-Fi (802.11 b/g/n), Ethernet
- Power USB Type-C, Powered by POE
- Radiofrequency: 433.92MHZ
- Dimension L75 W75 H30 (mm)
- Poe 1.6A-1.3A 42V-57V
- Work temperature-5 °C~50 °C
Status Indicator
FCC
Changes or modifications not expressly approved by the party responsible for compliance could void the use’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC RF Radiation Exposure Statement
- This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
- This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>