AXAGON ADSA-CC Superspeed USB-C 10Gbps CloneMaster Adapter Instruction Manual

INSTRUCTIONS
FOR USE (original) revision 1.0 ADSA-CC SUPERSPEED USB-C 10Gbps
NVMe M.2 SSD + SATA 2.5″% 3.5″ HDD/SSD
Clone Master 2 ADAPTER
WITH CLONE FUNCTION
Instructions for use 011

MOUNTING OF DISKS

INSTALLATION STEPS-CONNECTION

1. Connect power supply to the DC 12V connector. Use the provided AC/DC adapter for power supply. No power adapter connection required for M.2 and 2.5′ HDD / SSD.
2. Connect the adapter to the computer. For connection use the supplied cable.
3. Mount the NVMe M.2 drive (see Figures 1-4) and/or connect the SATA drive to the adapter.
4. Switch on the adapter using the OFF/ON switch on the back.
5. The disk will be detected and installed automatically.

SAFE REMOVAL OF DEVICE

1. If you want to disconnect the drive, make sure that data copying is completed and the SATA or M.2 data transfer light is not flashing.
2. Then use the OFF/ON power switch to turn off the adapter. The adapter and the disc are disconnected from the computer.
3. However, the safest method of disconnecting disks from computers is to use the function of the Windows operating system – safe removal of hardware. We recommend using this method.
4. Only when the adapter is disconnected from the computer you can disconnect the AC/DC adapter from the station.

INFO

• After connecting to the computer using the USB cable, the disk is always automatically Plug&Play detected.
• If the disk is detected in the Device Manager, but it is not displayed in the My Computer folder, check that disk letter has been assigned in the Disk Manager.
• Initialize and format the new disk in the Disk Manager.

CLONE FUNCTION

CLONING/DUPLICATING DISK CONTENT – CLONE FUNCTION

1. Connect power supply to the DC 12V connector. Use the provided AC/DC adapter for power supply.
2. Do not connect the adapter to the computer using the USB cable.
3. Mount the NVMe M.2 drive (see Figures 1-4).
4. Connect the 2.5″/3.5′ SATA drive to the adapter.
5. Press the OFF/ON switch at the back of the adapter to switch on power and wait for 10 seconds.
6. Select one of the two options with the cloning direction switch: 1 – the contents of the M.2 NVMe drive will be copied to the 2.573.5″ SATA drive, 2 -the contents of the 2.5″/3.5′ SATA drive will be copied to the M.2 NVMe drive).
7. All contents of the source disk will be copied to the destination disk.
8. During duplication, indication diodes 25%/50%/75%/100% will be blinking. Data duplication is finished when all LEDs light continuously.

INFO

• The size of the target disk must be equal or larger than the size of the source disk.
• lithe target disk is larger than the source disk, the remaining space on this target disk is not assigned. The unassigned space can be managed in the Disk Manager in Windows.
• The cloned disk is an identical copy of the source disk and it also takes the ID of the source disk. Therefore Windows will switch off one of the disks if both are connected to the computer after cloning. The switched off disk can be switched over again to the online mode in the Disk Manager in Windows.

TECHINICAL SPECIFICATIONS

USB3.2Gen 2+ USB3.2
Gen 1 (USB3.0)- USB2.0
10000 – 5000 – 480 Mbit/s
(SuperSpeed USB 10 Ghps – SuperSpeed USB – ighSpeed)
USB Type
C female connector (on the adapter)
SUPPORTED DEVICES
NVMe (PCI-Express) .2 SSD single or double sided disks no disk capadity limitation
M.2 disk dimension support: 2242, 2260, 2280 mm M-KEY
& B-+M-KEY NVMe M.2 SSD disks supported NGFF 75-pin M-KEY slot for NVMe M.2 SSD disks 2.5″&3.5″ SATAIII/1I /1 HDD &SSD supported no disk capadity limitation 22-pin SATA data and power female connector for SATA disks
SIZENETWEIGHT
102x68x 15 mm « 73 g – 30 cm detachable cable USB-C:> USB-C with USB-C > USB-A adapter
POWER SUPPLY
Power through indluded power adapter (12V/2A)
USB bus power is enough for adapter with M.2 NVMe and 2.5″ HDD/SSD disk connected.
CLONING FEATURES
Cloning takes place without connecting the adapter to a computer. The target disk must have the same or larger capacity as the source disk, otherwise doning cannot be started.
The total disk cloning time depends on the capacity of the source disk, not the amount of disk data.
OTHER FEATURES
Plug &Play – S.M.AR.T. – TRIM – UASP – BOT Ve M.2.650 o SATA HDD/SSD disk boot subpart n adapter
The total bandwidth /transmission rate i determined by the USB 3.2 Gen 2 interface used (theoretically up to 10 Gbits).
The real bandwidth / transmission rate is about 1000 MB/s (1 GB/s) it is given by the limits of the USB 3.2 Gen 2 interface.
Compliant with PCI Express Base Specification Revision 3.1a specification Compliant with NVM Express 1.3¢ specification Automaticinstallation Screwless mounting
LED INDICATION
2xorange LED – eachforoneis,disk connection (permanently on), data transmission (fashes) 4x blue LED 25%-50%-75%-100% – cloning takes place (flashes), diminished (permanentligh) “Ixgreen LED – poir supply turned on (permanently on) 05 SUPPORTED WINDOWS 7 +8.1-10- 11 &later Server 2008 – 2012 2016+ 2019 – 2022 & after 328 64t versions supported 05X10.4 & later Linux 2.6.x& later
Note: drivers are usually part of 0S; when Windows 7 used it is necessary to check 05 support and driver availability with the M.2 SSD manufacturer,

PRODUCT SUPPORT LINK
http://axagon.eu/produkty/adsa-cc#supportLinkGoal
SuperSpeed USB 10Gbps adapter for NVMe M.2 and 2.5″/3.5″ SATA disks with cloning functior

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>