CRYSTORAMA 5008-CH-CL-MWP Eight Light Chandelier Instruction Manual

CRYSTORAMA 5008-CH-CL-MWP Eight Light Chandelier Instruction Manual

Part Number

Part Numbers

• A.(2)-Wire Connector

• B. (1)-Mounting Bar

• C. (1)-Lock Washer

• D. (1)-Hex Nut

• E. (1)-Nipple

• F. (1)-Canopy (W5″xH1″)-XSN5008CHCAN5IN

• G. (1)-Collar Ring
  H. (1)-Collar Loop

• I. (1)-Chain(4mmx72″)-XSN5008CHCHA4MM

• J. (1)-Center Column Kit Loop

• K. (1)-Center Column Kit

  • Top Bobeche;Ø6″,8pin,14mm center hole.
  • -XSN5008CHBOB8PN
  • Glass Vase ; H8″
  • Metal Cover ; H1 2/8

• L. (8)-PVC Candle Sleeve

• M. (9)-Bobeche ; Ø5″,5 pin,24mm center hole.

  • -XSN5008CHBOB5IN

• N. (8)-10″Arms-XSN500CHARM10INKD

• O. (8)-6″Scrolls-XSN5008CHSCR

• P. (8)-Holder

• Q. (8)-Female Plug

• R. (1)-Distributor Kit

  • Coupling.
  • Metal Bowl.
  • Center Bowl ; Ø6″,no pin,13mm center hole.
  • Glass Vase; H6″
  • Distributor Box.
  • Thread

• S. (1)-Bottom Bowl; Ø6″,no pin,13mm center hole.

• T. (2)-Check Ring ; Ø1 3/8″

• U. (1)-Finial-XSN5008CHFIN

Crystal Sets

• A. 8 Sets. (2)14mm + AS9-2″
  B. 8 Sets. (1)Ring + (1)14mm + (1)Square
  C. 16 Sets. (18)14mm
  D. 8 Sets. (7)14mm + AS9-2″
  E. 45 Sets. (1)14mm + AS9-2″

• F. 8 Sets. (10)14mm

• G. 1 Piece. (2)14mm + AS8-40mm Ball

• H. 8 Sets. (1)14mm + AS9-3″

• I. 8 Sets. (1)Ring + (1)Square

DETAILED ILLUSTRATION

1. Bobeche with Ex5 102″ 27″
   

WARNING:

Electrical Danger

Turn Power Off

All electrical components must be installed by a licensed electrician in accordance with the National Electric Code and the appropriate local elecrical codes You will need 8- Candelabra Base Bulb 40 Watts recommended 60 Watts Max. USE LED BULBS FOR EXTENDED USE

The fixture is Dry rated

HOW TO INSTALL

Place the fixture parts on a soft cloth-covered platformbefore installation of fixture.

1. Screw the Center column kit onto the distributor kit.

2. Place the bottom bowl, check ring, bobeche, check ring, in that order,over the bottom distributor box. Secure with the finial.

3. To install the glass arms, slightly loosen each screw on the top plate over the distributor box. Pull a female plug through a hole in the plate.Connect the male plug at the end of the arm with the female plug that was just pulled.
   Push the end of the arm with the metal tab through the hole until stopped by the metal tab(this should also push the wires and plugs back inside the metal plate). Twist the metal tab counter-clock wise until both inserts lock onto the loose screws.
   Tighten the screw securing the arm in place.Repeat for all arms.

4. Insert the scrolls onto the holder and Put the bobeche over the socket.

5. Attach the mounting bar onto the outlet box

6. Decide the desired hanging height and adjust the chain to the correct length.

7. Raise the fixture up and do the wire connection. Attach the canopy over the mounting bar and secure with collar ring.

8. Dress the crystals as illustrated.

WARING: This product can expose you to Lead, which is known to the State of California to cause cancer and/or birth defects or reproductive harm.For more information go to www.p65warnings.ca.gov

References

• p65warnings.ca.gov

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>