strands 809255 Dark Knight Fortex Amber Single Instruction Manual

Strands 809255 Dark Knight Fortex Amber Single

Product Information

Specifications:

• Model : DK FORTEX WORKLIGHT 39W
• Part Numbers: 809255, 809256
• Colour Options:
  • 809255: Redwork light, Yellow position light, Green switch colour temp.
  • 809256: Redwork light, Amber position light, Green switch color temp.
• Power: 39W
• Positive (+) Connection: Red wire (+V DC)
• Negative (-) Connection: Black wire (Chassis Ground)

Product Usage Instructions

• Installation:
  Before installation, read all instructions and study diagrams provided in the manual. Do not use a dark cover while the work light is on.

• Legal Mounting:
  Check with state or local authorities for laws governing usage and proper mounting of the lights.

• Maintenance:
  Keep the product clean. Dirt on the lens and heat sink may shorten the product’s lifetime. We recommend using lukewarm water and alkaline degreasing for cleaning. Follow the degreasing instructions carefully and rinse off gently with cold or lukewarm water on low pressure.

• Connector and Cable:
  If there is a connector on the product, do not cut it to maintain warranty validity. If the cable is loose and has no connector, do not cut it if it is shorter than 50 cm to keep the warranty valid. If longer than 50 cm, it is okay to shorten it, but not below 50 cm. Tighten screws and bolts securely without over-tightening to avoid damaging the product.

Contact Information: For support or inquiries,

• contact : support@strands.se or +46(0)320-450450
• Websites : www.strands.se,   www.strandseurope.com

Dimension

809255
RED = + POSITIVE/ WORK LIGHT (+V DC) BEACON REPOSION EN
GREEN = SWITCH COLOR TEMP. (TO +V DC)
809256
RED = + POSITIVE/ WORK LIGHT (+V DC)
BLACK = – TO CHASSIS GROUND
YELLOW = AMBER POSITION LIGHT
GREEN = SWITCH COLOR TEMP. (TO +V DC)

READ THIS BEFORE INSTALLATION

READ ALL INSTRUCTIONS AND STUDY DIAGRAMS BEFORE INSTALLING YOUR NEW LIGHTS! “Do not use a dark cover while the work light is on”

LEGAL MOUNTING

Check with state or local authorities for laws governing usage and proper mounting of your new lights.

TAKE CARE OF YOUR PRODUCT

• Keep the product clean. Dirt on the lens and heat sink may shorten the product’s lifetime.
• We recommend using lukewarm water and alkaline degreasing.
• Follow the degreasing instructions carefully and rinse off gently with cold or lukewarm water on low pressure.

WARNING!

• Strong chemicals should not be used on the product. If you accidently get strong chemicals on the product, rinse off immediately, use plenty of water so that no chemicals remain in any joint.
• Some chemicals have a small amount of solvent in them, this can dissolve sealing adhesives and compromise the product’s waterproofness.
• Some chemicals pull out liquid from plastic and rubber-based components, which makes the plastic or rubber brittle and burst more easily.
• Be careful not to use high water pressure close up on the product.
• If you use high water pressure at short distances, most products find it difficult to close out the water.

INSTALLATION

• If there is a contact/connector on the product, it should not be cutted. If the connector is cut, the warranty is not valid.
• If the product has loose cable and no connector. If the cable is shorter than 50 cm, the cable must not be cutted. If the cable is cut, the warranty is not valid.
• If the cable is longer than 50 cm, it is ok to shorten the cable, but not shorter than 50 cm.
• If the cable is cut shorter than 50 cm, the warranty is not valid.
• Tighten screws and bolts so that they do not loosen or chafe.
• Do not tighten screws so hard that the protective bearings on the product breaks.

WARNING!

• Do not use higher volts than the product description states.
• This light becomes hot under continuous use.
• Don’t remove or touch the casing for at least 30 minutes after turning the lamp off.

Part no. 809255, 809256
Contact us if you need support:

• support@strands.se or +46(0)320-450450
• www.strands.se
• www.strandseurope.com

FAQ

Q: Can I cut the cable of the product?
A: If the cable is shorter than 50 cm, cutting it will void the warranty. If it is longer than 50 cm, it can be shortened but not below 50 cm.

Q: What should I do if there is a connector on the product?
A: Do not cut the connector to ensure warranty validity.

References

• Proffs på Fordonsbelysning & Lastbilstillbehör - Strands
• Proffs på Fordonsbelysning & Lastbilstillbehör - Strands

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>