Sunricher SRP-2305N-10CC100-500 10W DALI DT6 NFC Enabled LED Driver Instruction Manual

Sunricher SRP-2305N-10CC100-500 10W DALI DT6 NFC Enabled LED Driver

Important: Read All Instructions Prior to Installation

Function introduction

Product Data

Total Harmonic

Distortion

| THD ≤ 15% (@ full load / 230VAC)
Efficiency (Typ.)| ＞80% @ 230VAC full load
AC Current (Typ.)| 0.1A @ 230VAC
Inrush Current (Typ.)| Max. 4.32A at 230VAC; 80μs duration
Leakage Current| < 5mA /230VAC
Standby Power Consumption| ＜0.5W
Anti Surge| L-N:2KV
Control| Dimming Interface| DALI Device Type 6 (DALI consumption < 2mA)/ AC Push
Dimming Range| 0.01%-100%@ Max current
Dimming Method| Amplitude/CCR dimming
Dimming Curve| Linear/ Logarithmic optional
Protection| Short Circuit| Yes, recovers automatically after fault condition is removed
Over Current| Yes, recovers automatically after fault condition is removed
Over Temperature| Yes, recovers automatically after temperature drop
Environment| Working Temp.| -25℃ ~ +45℃
Max. Case Temp.| TC=85℃ (Ta=”45℃”)
Working Humidity| 10% ~ 95% RH non-condensing
Storage Temp. & Humidity| -40℃ ~ +80℃, 10% ~ 95% RH
Safety & EMC| Safety Standards| EN61347-1, EN61347-2-13
Withstand Voltage| I/P-O/P: 3.75KVAC
Isolation Resistance| I/P-O/P: 100M Ohms / 500VDC / 25℃ / 70% RH
EMC Emission| En55015, EN61000-3-2, EN61000-3-3
EMC Immunity| En61547, EN61000-4-2,3,4,5,6,8,11
Others|

MTBF

| 191350H, MIL-HDBK-217F @ 230VAC full load

and 25℃ ambient temperature

Dimension| 101x36x25mm (LWH)
Warranty| 5 Years

• In compliance with IEC 62386-101 :2014, I EC 62386-102:2014, IEC 62386-207 Ed2 ,
• Built-in DALl-2 interface, DALI DT6 device
• Dimmable LED driver. Max. output power 1 OW
• 100-SOOmA current selectable via NFC program tool. Min.cu rrent gear lower to 0.1 mA
• DALI Address/Group/Scene setting via NFC program tool.
• Class II power supply, full isolated plastic case
• High power factor and efficiency
• To switch and dim LED lighting luminaries
• Amplitude/CCR dimming, smooth and deep dimming
• Compatible with universa l DALI masters that support DT6 commands
• Error report function
• IP20 rating, suitable for indoor LED lighting applications
• 5 years warranty

Safety & Warnings

• DO NOT install with power applied to the device.
• DO NOT expose the device to moisture.

Operation

With DALI master

DALI Address

1. DALI address for 1 channel output are assigned by DALI Master controller automatically, please refer to user manuals of compatible DALI Masters for specific operations.

With NFC Programming devices

Note

1. Do wiring according to the wiring diagram and power on the DALI system .
2. Recommend setting parameters without power-on the DALI devices .
3. Please make sure your mobile phone has NFC function and enable it .

Working with “SR NFC Tool” APP

Step 1: Download the APP (searching “SR NFC Tool” from App Store and Google Play) . Then open the APP .

Note:

1. Please Make sure that you have enabled NFC function with your mobile phone/ tablet .
2. Please Make sure that the “NFC position” is matched.
3. Please do not power on the device before setting.
4. If you can’t download “SR NFC Tool”. Please contact with us.

Step 2: Add device, and name it as you wish

Step 3: Unlock device, enter parameters configuring page.

Note:

1. You have to unlock the device then do some settings
2. Only when the corresponding function is selected, the function interface will be displayed.

Step 4: Few parameter interface, you can choose the setting based on your requirements.

Step 5: After setting, please save the selected configuration via NFC and power on the device.

Tips

1. NFC function doesn’t require any power driver.
2. Many functions can be configured by NFC. Kindly check your desired functions.
3. All of our DALI drivers are in the best performance within our DALI master/ gateway.

Wiring Diagram

With DALI bus

1. With single color LED luminarie
   

2. With PUSH dimmer
   

AC Push Function

1. Click the button to switch ON/OFF
2. Press and hold down the button to increase or decrease light intensity to desired level and release it, then repeat the operation to adjust light intensity to opposite direction. The dimming range is from 1% to 100%.

Product Dimension

Operating window

Dimming Curve

Note: Test data under 500mA gear

Driver Performance

Note: Test data under 500mA gear

Driver Performance

Note: Test data under 500mA gear

MCB Load Quantity

Module Number| Ipeak| Twidth| Max.quantity of LED Driver per MCB
B10 B13 B16 B20 B25 C10 C13 C16 C20 C25 D10 D13 D16 D20 D25
---|---|---|---
SRP-2305N-10CC100-500| 4.32A| 80μs| 34| 45| 55| 69| 86| 57| 75| 920| 115| 144| 80| 104| 128| 160| 200
SRP-2309N-10CCT100-500| 4.32A| 80μs| 34| 45| 55| 69| 86| 57| 75| 92| 115| 144| 80| 104| 128| 160| 200

Note:

1. Those MCB parameters are based on ABB S200 series circuit breakers.
2. For different brands and models of miniature circuit breakers, the quantity of drivers will have difference.
3. Please do not exceed the above-mentioned quantity during on-site installation, and the specific load quantity shall be subject to on-site installation.
4. When the installation environment temperature of MCBs exceeds 30°C or when multiple MCBs are installed side by side, the number of mounted drives will be reduced, which requires recalculation.
5. Type C MCB’s are strongly recommended to use with LED lighting

Update log

Note： Subject to change without notice. Please contact us if you have any questions.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>