NINGBO JF4025X-WX Wireless Fast Chargingpad User Manual

: June 12, 2024
: Ningbo

Table of Contents

NINGBO JF4025X-WX Wireless Fast Chargingpad
Product Information
Product Usage Instructions
Supplied Accessories
Features
Specifications
FCC STATMENT
WIRELESS FAST CHARGING PAD USER MANUAL
Read User Manual Online (PDF format)
Download This Manual (PDF format)

NINGBO JF4025X-WX Wireless Fast Chargingpad

Product Information

The Wireless Fast Charging Pad is a device that enables wireless charging for mobile phones. It has an output of 10+5W and can be mounted on magnetic surfaces or permanently mounted using built-in screw holes. This device complies with Part 15 of the FCC Rules and is made by Ningbo Weijia Electronics Technology Co., Ltd. in China.

Product Usage Instructions

Place the Wireless Fast Charging Pad on a flat surface.
If you want to mount it on a magnetic surface, attach the magnet (B) to the back of the pad and then stick it onto the surface.
If you want to permanently mount it, use the built-in screw holes to attach it to the surface.
Connect the device to a power source using the TYPE-C cable (E).
Place your mobile phone on the mobile phone support (D) with the screen facing up and make sure it is aligned with the charging coil (C).
The indicator light (A) will turn on to show that the phone is charging.
If you want to charge wireless series lights, place them on the pad as well.

Note: To ensure compliance with FCC/IC RF exposure requirements, maintain a separation distance of 20 cm or more between the antenna of this device and persons during device operation.

Supplied Accessories

FCC ID: 2BAZE-JF2117
REF: JF2117
Input: 5-12VDC, 20W
Output: Max. 10+5W

Features

Charges two devices simultaneously
Works with compatible mobile phones
IK08 shock resistance
Strong magnets on the rear allow for easy mounting on magnetic surfaces as well as built-in screw holes for permanent mounting

Specifications

Material: Ultra-tough nylon, Aluminium, Rubber, PC&TPE
If charging by wireless pad: Charging time: Approx 3.0-8.0 hours depending on battery pack – the environmental temperature will affect the charging and discharging period of the battery
Operating temperature: -5°C to +30°C
Charging pad measurements: 265 x 110 x 29 mm
Net weight: 330g (packaging not included)

Disposal and environmental protection

Do not dispose of charging pads with domestic waste
Please check with local recycling plants for the best way to recycle
This charging pad contains substances that may be harmful to the environment and humans if disposed of inappropriately

FCC STATMENT

Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

this device may not cause harmful interference, and
this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

MPE caution: To satisfy FCC / IC RF exposure requirements, a separation distance of 20 cm or more should be maintained between the antenna of this device and persons during device operation. To ensure compliance, operations at closer than this distance is not recommended.