TRUE FINE TD90027C 4 Light Chandelier Instruction Manual

June 12, 2024
TRUE FINE

TRUE FINE TD90027C 4 Light Chandelier

Product Information

The 4-Light Chandelier is an elegantly designed lighting fixture that is perfect for indoor use. It has a fixture body with an input voltage of 120V and requires four E26 bulbs (not included). The package includes a mounting bar, canopy, canopy lock ring, fixture chain, loop, and mounting strap. The chandelier comes with a green grounding screw for proper grounding.

Product Usage Instructions

  1. Insert the green grounding screw into the hole with two raised dimples on the mounting bar. If the ground wire is supplied with the fixture, wrap it around the green grounding screw and connect it to the ground wire from the outlet box using a wire connector (not supplied). If the ground wire is not supplied with the fixture, wrap the ground wire from the outlet box around the green grounding screw and tighten it.
  2. Identify the color of the wires on your fixture and group them accordingly. Connect Group A wires to the black house wire and Group B wires to the white house wire.
  3. Place the fixture wire(s) from Group A against the black wire from the outlet box.
  4. Fit a wire connector over the wires and screw it clockwise until you feel firmness. Try gently to pull the connector off the wires. If you can pull the connector off, carefully re-do steps 3 and 4 and check again for a firm connection.
  5. Connect the fixture wire from Group B to the white wire from the outlet box in the same manner. Make sure no bare wires can be seen outside wire connectors.
  6. Fix Mounting strap (H) to outlet box with Screw (I).
  7. Thread the wires through Canopy (G) and Mounting strap (H), link Loop (D) and Mounting strap (H) by Fixture chain (E).
  8. Connect the wires according to the picture provided in the wiring instruction.
  9. Fix Canopy (F) to Mounting strap (G) with Canopy lock ring (E).
  10. Install the four E26 bulbs (not included).
  11. Hang Smaller lampshade (C) to the bottom of Larger lampshade (B).

Overview

Assembly Instruction

  1. Thread the wires through the hole in the top of Larger lampshade(B), then screw Loop (D) to Fixtrue body (A).
  2. Fix Mounting strap (H) to outlet box with Screw (1).
  3. Thread the wires through Canopy (G) and Mounting strap (H), link Loop (D) and Mounting strap (H) by Fixture chain (E).
  4. Connect the wires according to the picture above. (Please refer to the wiring instruction for details )
  5. Fix Canopy (F) to Mounting strap (G) with Canopy lock ring (E).
  6. Install the bulbs (Not included), need four E26 bulbs.
  7. Hang Smaller lampshade (C) to the bottom of Larger lampshade (B).

Wiring Instruction

  1. Insert the green grounding screw into the hole with two raised dimples on the mounting bar. Wrap the ground wire from the fixture (if supplied) around the green grounding screw, then connect it to ground wire from the outlet box (if not fixed on the outlet box) using a wire connector(not supplied). If ground wire from the fixture is not supplied, wrap the ground wire (if not fixed on the outlet box) from the outlet box around the green grounding screw and tighten it. NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES.
  2. Take note of the color of the wire(s) on your fixture. Identify which group your fixture wire(s) falls into and connect the wires according to the directions below:
    [GROUP A]:

Connect to Black House Wire

| [GROUP B]:

Connect to White House Wire

---|---
BLACK| WHITE
PARALLEL WIRE (round & smooth)| PARALLEL WIRE (square & ridged)
WHITE OR GREY WITH TRACER| WHITE OR GREY WITHOUT TRACER
BROWN, GOLD OR BLACK WITHOUT TRACER| BROWN, GOLD OR BLACK WITH TRACER
3. Take your fixture wire(s) from [Group A] and place evenly against the black wire from the outlet box. Do NOT twist wires together before using wire connectors. 4. Fit a wire connector over the wires and screw the connector clockwise until you feel firmness. 5. Try gently to pull the connector off the wires. If you can pull the connector off, carefully re-do steps 3 and 4 as above, and check again for a firm connection. 6. Connect the fixture wire from [Group B] to the white wire from the outlet box in the same manner. Make sure no bare wires can be seen outside wire connectors.

Product Specifications

  • Input voltage: 120V
  • Rated power: 40 MAX × 4
  • Lamp socket: E26

Product Packaging

  • Fixture body × 1
  • Mounting strap × 1 & Canopy × 1
  • Larger lampshade × 1 & Smaller lampshade × 1
  • Fixture chain × 1 & Loop × 1
  • Screw × 2 & Wire nut × 3
  • Lamp instruction × 1

Cleaning

  • To clean, wipe the fixture with a soft cloth. Clean glass with a mild soap.
  • Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

Safety Information

  • Always switch off the electricity supply and allow to cool for 10 minutes before changing the light bulbs.

CONTACT US

Print in china

References

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

TRUE FINE User Manuals

Related Manuals