MINKA LAVERY 2952-572 Upham Estates 2-Light Coal and Polished Nickel Wall Sconce Installation Guide
- October 30, 2023
- MINKA LAVERY
Table of Contents
MINKA LAVERY 2952-572 Upham Estates 2-Light Coal and Polished Nickel Wall
Sconce
Product Information
The product is a fixture with item number 2952-572 that comes with a mounting plate, ground screw, mounting screws, back plate, cloth shade, candle covers, and candelabra base bulbs. The fixture can accommodate up to 60 watts per bulb and should not exceed the maximum wattage rating. It is important to shut off power at the fuse box or circuit breaker before installation. The fixture wires consist of black/smooth wire, white/ribbed wire, and green/bare copper wire for grounding. The installation manual also includes an illustration (Fig.1) for reference.
Product Usage Instructions
- Shut off power at the fuse box or circuit breaker box.
- Remove the old fixture including the mounting hardware.
- Unpack the new fixture and lay out all the parts in a clear area. Take care not to misplace any small parts necessary for installation.
- Loosen screws to remove the mounting plate from the back plate.
- Attach the mounting plate to the junction box using the mounting screws. The side of the mounting plate marked GND must face out.
- Connect the electrical wires as shown in Fig. 2, making sure that all wire connectors are secured. If your junction box has a ground wire, connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box.
- Place the back plate over the mounting plate and fasten with screws.
- Place the cloth shade over the back plate and secure with screws.
- Place the candle covers over the sockets.
- Install two candelabra base bulbs up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification. Do not exceed the maximum wattage rating.
- Turn on power and test the fixture.
WARNING ! SHUT POWER OFF USE OR CIRCUIT BREAKER .
MOUNTING THE FIXTURE (Fig.1)
-
Shut off power at the fuse box or circuit breaker box and remove the old fixture including the mounting hardware.
-
Carefully unpack your new fixture and lay out all the parts in a clear area. Take care not to misplace any small parts necessary for installation.
-
Loosening screws (D) to remove mounting plate
(A) from back plate (C). -
Attach mounting plate (A) using the mounting screws (B) (Size: #8-32N*L0.5”) to the junction box. The side of the mounting plate marked “GND” must face out.
CONNECTING THE WIRES (Fig. 2)
- Connect the electrical wires as shown in Fig. 2, making sure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate (A) using the green screw provided. After wires are connected, tuck them carefully inside the junction box.
FINISHING THE INSTALLATION (Fig.1)
- Place back plate (C) over mounting plate (A) and fasten with screws (D).
- Place cloth shade (H) over back plate (C) and secure with screws (I).
- Place candle covers (F) over sockets (E).
- Install (2) two candelabra base bulbs (G) up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification. —DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!
Your installation is now complete. Return power and test the fixture.
Note: Illustration (Fig.1) on this manual is for installation purposes
only. It may or may not be identical to the fixture purchased.
MIN 75℃ SUPPLY CONDUCTORS
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>