CONRAD 2498121 Rechargeable Hedge Trimmer Instruction Manual

: June 4, 2024
: CONRAD

Table of Contents

Introduction
Description of symbols
Intended use
Delivery content
Safety information
Components and controls
Preparation
Operation
Troubleshooting
Maintenance/cleaning/storage
Technical data
Declaration of Conformity (DOC)
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

CONRAD 2498121 Rechargeable Hedge Trimmer Instruction Manual

Introduction

Dear customer,
Thank you for purchasing this product.
This product complies with statutory, national and European regulations.
To ensure that the product remains in this state and to guarantee safe operation, always follow the instructions in this manual.

These operating instructions are part of this product. They contain important information on setting up and using the product. Do not give this product to a third party without the operating instructions. For this reason, retain these original operating instructions for reference!

If there are any technical questions, please contact: www.conrad.com/contact

Description of symbols

The icon with the exclamation mark in a triangle indicates particular hazards associated with handling, use or operation.
Read the operating instructions carefully before first use.
Wear safety goggles
Wear ear defenders.
Wear protective gloves.
Do not use in rain or on wet hedges. Protect from water and moisture.
Caution – risk of cut injuries
Remove the battery before carrying out any adjustment or cleaning work, or when the appliance is unattended.
Keep other people away from your work space.
Warning – the device may throw other objects out of position.
Sound power generated by the device.

Intended use

The device is intended to be used for the manual cutting of hedges, shrubs and bushes. The device is not suitable for cutting grass, very hard bushes or wood, or for shredding composting material.

It is only suitable for use below shoulder height. Use above the head is not permitted.

This appliance is designed for use in private premises. Commercial use is not permitted.

This product must only be used in dry areas. Do not expose the product to precipitation or place it in or under water during use.

For safety and approval purposes, do not rebuild and/or modify this product. Using the product for purposes other than those described above may damage the product. In addition, improper use can cause hazards such as injury, a short circuit, fire, etc.

Read through these original operating instructions carefully and keep them in a safe place. Only make this product available to third parties together with its original operating instructions.

Delivery content

Cordless hedge trimmer
Blade guard
Original operating instructions

Up-to-date operating instructions

Download the latest operating instructions at www.conrad.com/downloads or scan the QR code shown. Follow the instructions on the website.

Safety information

Read the original operating instructions and safety information carefully. If you do not follow the safety instructions and information on proper handling in these original operating instructions, we will assume no liability for any resulting personal injury or damage to property. Such cases will invalidate the warranty/guarantee.

General safety information

Observe all safety information, instructions, drawings and specifications that are supplied with this tool. Failure to do so may cause fire and/or injury.
Keep these original operating instructions in a safe place so that you can refer to them at any time.
The product is not a toy and should be kept out of the reach of children! The product must be placed, used and stored in areas that are inaccessible to children.
Children must be supervised to make sure they do not play with appliance.
If it is no longer possible to operate the product safely, stop using it and prevent unauthorised use. Safe operation can no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stress.
Handle the product carefully. It can be damaged by impact, blows, or by being dropped, even from a low height.
Do not leave packaging material lying around carelessly. It may become a dangerous plaything for children.
Pay attention to all additional safety information in the individual sections of these original operating instructions.
Consult a technician if you are not sure how to use or handle the product, or if you have concerns about safety.
Maintenance, modifications and repairs must be carried out by a technician or a specialist repair centre.
If you have questions which remain unanswered by these original operating instructions, contact our technical support service or other technical personnel.
The product must be operated under the supervision of qualified personnel in schools, educational facilities, hobby and DIY workshops.

Personal safety

Do not use the tool when you are tired or under the influence of drugs, alcohol or medication. A moment of carelessness can cause serious injuries.
Always use the tool carefully. Avoid the familiarisation effect if you have already worked with the tool a lot. Always observe the safety instructions and always stay alert. A moment of carelessness can result in serious accidents.
Use personal protective equipment. Always wear safety goggles, sturdy shoes, long trousers, ear protection and protective gloves. Never work barefoot or wearing sandals.
Wear appropriate clothing. Do not wear jewellery. Hair, jewellery or clothing can be caught in moving parts – risk of injury! Use a hair net or similar if you have long hair and wear close-fitting clothes when using the product.
Prevent unintentional switching on of the tool. Always make sure that the on/off switch is switched off when you store, pick up or carry the device and before you insert or remove the battery from the device. Do not carry the tool with your finger on the on/off switch.
Make sure you are stood firmly on the ground while working and avoid an abnormal posture. This makes it much easier to control the tool in unforeseen circumstances.
Always observe all relevant national regulations (e.g. occupational safety measures)

General safety warnings for power tools

Do not overload power tools. Only use power tools for their intended purpose. A suitable tool does the job better and, more importantly, more safely.
Check the on/off switch before each use. Using the tool with a damaged on/off switch hinders control of the tool and is therefore very dangerous.
Always remove the rechargeable battery when you
- are adjusting the trimmer
- storing the appliance
- removing a blockage
- feel unusual vibrations
- or after contact with a foreign body (in this case, check the appliance for damage and, if necessary, have it repaired by a specialist)
Keep power tools out of the reach of children. Do not allow people who are unfamiliar with the appliance and/or have not read and understood these original operating instructions to use it. Power tools are very dangerous in the hands of inexperienced users.
Service the tool regularly and check for signs of damage, dirt, incorrect settings, wear and tear or other issues that may present a hazard. Ensure that damaged devices are repaired by a specialist before use. Poorly maintained tools often lead to accidents.
Use the tool and its accessories only for the specified purpose and in accordance with these original operating instructions. Also pay attention to the working conditions and the task that you plan to carry out. Improper use can lead to hazardous situations.
Only use accessories and attachments that are compatible with the slots on the device.
Never attempt to switch off safety mechanisms.
Switch the device off immediately if the drive becomes blocked.
Keep the handles and surfaces of the tool dry, clean and free of oil or lubricants. Slipping during operation leads to a loss of control and accidents.
Hold the tool firmly. A sudden stop of the drive transfers the kinetic energy to the tool itself. This may cause the tool to fall out of your hands – risk of injury!
Condensation may form when the product is brought from a cold room into a warm one (e.g. during transportation). This can damage the product! For this reason, allow the product to warm up to room temperature before using it or inserting the battery. This may take several hours.

Safety warnings for battery-powered tools

Only use batteries that are specifically designed for this power tool. Using other batteries might result in injury and/or fire hazards.
Observe the safety and handling instructions in the original operating instructions of the battery and its charging device.
Never leave the appliance unattended when it is connected to the battery. Remove the battery before moving away from the appliance.

Workstation safety

Keep your workstation clean. Keep the work area well lit. A disorganised workstation or poor lighting can cause accidents.
Keep children and other people away from the workstation! Distractions can cause accidents.
Never use the product next to or near flammable liquids or gases, air/gas mixtures (petrol vapours) or flammable solids/dust. Sparks may be generated when the product is used – risk of fire or explosion!

Specific safety instructions for hedge trimmers

Never hold the blade during operation. Risk of injury.
The blade continues to run for a short period after being switched off.
Never try to remove clippings from the blade or hold the material you are cutting during operation. Only remove jammed clippings when the device is switched off. Ignoring these instructions may lead to serious injuries.
Keep body parts away from the blade during operation.
Always hold the hedge trimmer by the insulated handles. The saw blade could come into contact with hidden power lines and energise the metal parts of the hedge trimmer. Danger of electric shock!
Do not hold or carry the appliance by these safety devices.
Do not cut any wet material with the appliance. Do not use it in the rain or leave it outdoors overnight.
Never switch the device on if there are foreign bodies in the blade.
Before putting the hedge trimmer down or placing it on a surface, wait until the drive has come to a complete standstill.
Before operation, make sure that all screw connections are tightened and that the hedge trimmer is in a safe general condition.
Remove any adjusting tools, e.g. spanners, before turning the appliance on. The tool could be thrown out of position when the appliance is switched on and cause injuries.
Always hold the hedge trimmer firmly with both hands. This enables safe and controlled operation.
Thoroughly check the hedge to be cut before performing any work and remove any wires, cables or any other foreign bodies.
Do not insert any objects into the ventilation slots. In addition, make sure that no clippings or other materials fall into the vents. This may present a fire hazard due to overheating.
Keep cutting tools sharp and clean. Sharp cutting tools are less likely to get jammed and are easier to control.
Always attach the blade guard when storing or transporting the device or leaving it unattended.

Residual risks

This appliance complies with technical regulations and relevant safety regulations. However, the following may still occur during use:

Danger to the life and limbs of the user or other people.
Damage to the appliance.
Damage to other property.

Components and controls

Cutting blade
Hand protection
Bow handle with safety switch
Handle
On/off switch
Battery slot

Preparation

Always remove the battery before attempting any installation or adjustment work or changing accessories.
Inadvertent operation of the on/off switch (5) may cause injury.

Inserting/removing the battery

Slide the battery into the battery compartment (6) until it clicks into place.
To remove the battery, press the release button on the battery and pull it out of the battery slot (6).

Always remove the battery before storing the appliance or if you do not plan to use it for an extended period of time.

Operation

Always observe the safety information at the beginning of these operating instructions.

Before use, check the hedge trimmer for loose connection screws, firmly fixed adjustment devices and an intact blade.

Always hold the hedge trimmer with both hands on the handle (4) and on the bow handle with the safety switch (3).

Caution – the blade (1) continues to run for a short time after the trimmer has been switched off.

Remove the blade guard from the blade (1).
Press the safety switch on the bow handle (3) and switch on the hedge trimmer with the on/off switch (5).
Allow the hedge trimmer to get up to speed before starting your work and do not apply a load to the trimmer as soon as it is switched on.
Do not overload the hedge trimmer by cutting branches that are too big or by cutting too many branches at the same time. This also protects the tool and prevents an overload.
Move the hedge trimmer evenly in arching movements in front of your body over the area to be cut.
Hold the hedge trimmer so that the blade is at an angle of approx. 15° to the cutting surface.
The hedge trimmer cuts on both sides, which provides a high cutting power.
For a straight and uniform cut, it is advisable to use a guide. This enables, for example, the height of the hedge to be marked.
To switch off the hedge trimmer after operation or in the event of danger, simply release the on/off switch (5) or the safety switch on the bow handle (3).
Replace the blade guard after operation to prevent injuries caused by the blade.

Troubleshooting

No function, the appliance does not switch on:

The battery is depleted. Charge the battery using the corresponding charger.
The battery is not correctly inserted into the battery slot (6) on the appliance.

Cutting performance is poor:

The blade (1) is no longer sharp and should be sharpened by a specialist.
The battery is flat and should be recharged.

The blade (1) does not move:

Switch off the hedge trimmer immediately and remove the battery.
Check that there are no foreign bodies jammed in the blade (1).
If necessary, remove the foreign objects.

The hedge is not cut cleanly or the blade frequently gets stuck or becomes hot:

The blade (1) is worn or damaged and should be sharpened by a specialist.
The blade (1) is not sufficiently lubricated. Lubricate the blade (1) with oil.

Maintenance/cleaning/storage

Before cleaning or servicing the device, switch it off and remove the battery.

Under no circumstances should you service any of the components in the interior of the product, therefore never open/dismantle it. Repair and maintenance work (including opening the product) must be done by a technician or specialist repair centre.

Do not allow water or moisture to get inside the device.

Use a slightly damp cloth to clean the product. Do not use any aggressive cleaning agents or chemicals.
Improper cleaning agents can cause discolouration on the plastic surface. Never use scouring agents, alcohol, petrol, spirits or other similar liquids to clean the product.

Wear protective gloves during maintenance and cleaning work to prevent injury from sharp edges or the blade (1)

Maintenance

Check the blade (1) for wear and damage before and after each use.
If the blade (1) no longer cuts cleanly or gets caught on the material you are cutting, have the blade sharpened by a specialist.
After cleaning, apply maintenance oil or spray to the blade (1). This prevents corrosion and keeps the blade (1) moving smoothly.

Cleaning

Always clean the product immediately after use to prevent dust and dirt from settling.
Keep dust and dirt off the safety mechanisms, ventilation slots and the motor housing.
Remove dirt and foreign bodies from the blade with a brush.
To clean the motor housing, use a dry or slightly damp clean and lint-free cloth.
Thorough cleaning keeps the product in a usable condition and prolongs its lifespan. A good craftsman is careful with his tools!

Storage

When storing or not using the appliance, protect the blade (1) with the blade guard.
Store the appliance in a clean and dry place. Avoid frost.
Keep the device and especially the plastic parts away from substances such as brake fluid, petroleum, oil-containing substances and penetrating oil. These substances contain chemicals that can damage or destroy the plastic parts.
Fertilizers and other garden chemicals contain substances that can attack metals. For this reason, do not store the device close to such substances.
Store the device, the original operating instructions and the accessories in the original packaging. This ensures that you will always have all the necessary information and accessories at hand.

Disposal

Electronic devices are recyclable waste and must not be disposed of in household waste. At the end of its service life, dispose of the product in accordance with applicable regulatory guidelines.

Technical data

Rated voltage ………………………………………………………. 20 V/DC
Suitable rechargeable batteries (not included)…………..TOOLCRAFT 20 V/2.0 Ah (item no. 1881809)
TOOLCRAFT 20 V/4.0 Ah (item no. 1881810)
TOOLCRAFT 20 V/5.0 Ah (item no. 2331500)
Suitable charger (not included)………………………………..TOOLCRAFT 20 V/2.3 A (item no. 1881811)
TOOLCRAFT 20 V/5.0 A (item no. 1881812)
TOOLCRAFT 20 V/ 2x 4.5 A (item no. 2388640)
Cuts/min ………………………………………………………………1300
Cutting length ……………………………………………………….410 mm
Tooth spacing / max. cutting diameter………………………18 mm
Weight …………………………………………………………………1.99 kg
Sound pressure level LPA (according to EN 62841) ……………………84.4 dB(A)
Sound power level LWA (according to EN 62841)……………………….92.5 dB(A)
Standard deviation K ……………………………………………..3 dB (A)
Vibration level (in accordance with EN 62841)…………..1.27 m/s² (bow handle) 1.01 m/s² (handle)
Uncertainty K………………………………………………………..1.5 m/s²
Dimensions (L x W x H)………………………………………….89 x 19 x 20 cm
Operating/storage conditions…………………………………..+5 to +40 °C / <85 % relative humidity

Attention!
The noise level of the appliance may exceed 80 dB(A). Wear suitable ear defenders to prevent hearing damage.
The vibration emission value stated in this manual was obtained using a standardised EN 62841 test procedure. The result can be used to compare vibration levels of different electrical tools. It can also be used to obtain a preliminary estimate of your exposure to vibrations.
The specified value indicates the vibration level when the tool is used for its intended purpose. The actual vibration level may differ from the specified value if the tool is used for other purposes, if other tools are used, or if the tool has not been serviced properly. These factors can considerably increase your exposure.
For an accurate estimate of your exposure, account for the times when the appliance is switched off or not in use. These factors can considerably reduce your exposure.
Take additional safety measures to protect the user against the effects of vibration, e.g.: Maintenance of electric tool and insertion tools, keeping your hands warm, organisation of work processes.

Declaration of Conformity (DOC)

Conrad Electronic SE, Klaus-Conrad-Straße 1, D-92240 Hirschau, hereby declares that this product conforms to the following directives:
2006/42/EC
2014/30/EU
2011/65/EU + 2015/863/EU
It was manufactured in accordance with the following standards:
EN 62841-4-2:2019
EN 62841-1:2015+AC:15
EN 55014-1:2017+A11:2020
EN 55014-2:2015

Click on the following link to read the full text of the EU Declaration of Conformity: www.conrad.com/downloads
Select a language by clicking on the corresponding flag symbol, and then enter the product order number in the search box. The original EU Declaration of Conformity is available for download in PDF format.

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D 92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
This publication represent the technical status at the time of printing. Copyright 2022 by Conrad Electronic SE.