VISUAL COMFORT S2189 Halle Petite Wall Lantern Instruction Manual

VISUAL COMFORT S2189 Halle Petite Wall Lantern

Product Information

The Halle Petite Wall Lantern (Item # S 2189) is a light fixture designed for outdoor/wet location installation. The lantern features glass panels and a fixture body made of durable materials, and it requires a light bulb (not included) for operation. The lantern should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Careful inspection of the item and contents is necessary before installation, and packaging material should be retained until installation is complete and approved.

Product Usage Instructions

Tools Required: Phillips Screwdriver, Hammer,
Slotted Screwdriver, Drill, Pencil

1. Carefully remove all parts from the box. Place on a clean, soft surface.
2. Remove mounting plate (B) from fixture body (G) by removing side screws (F).
3. Remove lantern (I) from fixture body (G) by removing side screws (H).
4. Using mounting plate (B) as a guide, line up with the junction box and mark anchor positions
5. Using a drill bit slightly smaller than the anchor, drill holes in the marked positions. Install anchors (A) into holes using the hammer.
6. Install mounting plate (B) to junction box and secure with mounting screws (D), then secure wood screws (C) to anchors(A)
7. Wrap fixture ground wire (green) around the green grounding screw in the junction box and tighten.
8. Connect fixture wires to house wiring using wire connectors provided. White wire from fixture connects to white house wire, black wire from fixture connects to black house wire, and green/yellow wire from fixture connects to green house wire.
9. Push excess wiring into junction box and secure fixture to mounting plate (B) using side screws (F).
10. Install light bulb into the socket.
11. Install lantern (I) to fixture body (G) and secure with side screws (H).
12. Remove metal tabs (M) from lantern (I) by unscrewing screws (N), then install glass panels (J) & (K) & (L) to lantern (I) and secure with metal tabs (M) using screws (N). NOTE: Do not over-tighten otherwise shade could become damaged.
13. For outdoor/wet location installation, using silicon compound, apply a small bead where backplate meets the wall to prevent water from entering. NOTE: Large gaps will need to be corrected before applying silicon compound.

Care Instructions: Clean only with a soft dry cloth or feather duster. Do not use abrasive or chemical agents.

Halle Petite Wall Lantern
Item # S 2189

NOTICE: This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.

TOOLS REQUIRED (NOT INCLUDED)

• Phillips Screwdriver
• Hammer
• Slotted Screwdriver
• Pencil
• Drill

1. Carefully remove all parts from the box. Place on a clean, soft surface.

2. Remove mounting plate (B) from fixture body (G) by removing side screws (F).

3. Remove lantern (I) from fixture body (G) by removing side screws (H).

4. Using mounting plate (B) as a guide, line up with the junction box and mark anchor positions.

5. Using a drill bit slightly smaller than the anchor, drill holes in the marked positions. Install anchors (A) into holes using the hammer.

6. Install mounting plate (B) to junction box and secure with mounting screws (D), then secure wood screws (C) to anchors (A).

7. Wrap fixture ground wire (green) around the green grounding screw (see diagram 1). Tighten. Continue fixture ground wire and connect to supply ground wire (usually green or bare copper) using wire nut (E).
   NOTE: It is imperative that the fixture is grounded.

8. Connect fixture neutral wire (white) to the supply neutral wire (usually white) using wire nut (E).

9. Connect fixture hot wire (black) to the supply hot wire (usually black) using wire nut (E).
   CAUTION: Do not reverse the hot and neutral connections.

10. Make sure all wire connections are tight, then carefully tuck into the junction box.

11. Install fixture body (G) to mounting plate (B) and secure with side screws (F).

12. Remove metal tabs (M) from lantern (I) by unscrewing screws (N), then install glass panels (J) & (K) & (L) to lantern (I) and secure with metal tabs (M) using screws (N).
    NOTE: Do not over-tighten otherwise shade could become damaged.

13. Install light bulb into the socket.

14. Install lantern (I) to fixture body (G) and secure with side screws (H). FOR OUTDOOR/WET LOCATION INSTALLATION:

15. Using silicon compound, apply a small bead where backplate meets the wall to prevent water from entering.
    NOTE: Large gaps will need to be corrected before applying silicon compound.

Care Instructions: Clean only with a soft dry cloth or feather duster. Do not use abrasive or chemical agents.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>