VISUAL COMFORT KW 5022G-AIKW 5022G-AI Cubist Large Chandelier Instruction Manual
- October 30, 2023
- VISUAL COMFORT
Table of Contents
VISUAL COMFORT KW 5022G-AIKW 5022G-AI Cubist Large Chandelier
Product Information
The Cubist Large Chandelier (Item # KW 5022G/AI) is a light fixture that requires assembly. The chandelier does not come with a bulb and requires a 1/4 IPS threaded pipe (not provided) for installation. The chandelier comes with all the necessary parts, including L(3pcs), M, N, O(3pcs), A, B, C, D, E, F, G, G H, and K. The chandelier should be installed by a person familiar with the construction and operation of it, as well as the hazards involved. The product comes with assembly instructions and care instructions.
NOTICE: This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install it. Retain all packaging material until installation is complete and approved.
TOOLS REQUIRED
- Phillips Screwdriver
- Slotted Screwdriver
- Wire Strippers
- Slip Joint Pliers
- Chain Pliers
- Measuring Tape
- Wire Cutters
ASSEMBLY INSTRUCTIONS
-
Carefully remove all parts from the box. Place on a clean, soft surface.
-
It is recommended to install a 1/4 IPS threaded pipe, secured to a structural member of the building (not included). Then install hex nut and threaded nipple (B) into receiver and tighten with the wrench.
NOTE: Item must be supported independent of the junction box due to weight. -
Remove collar loop (C) from chain (F) and secure to threaded receiver attached to structural member by tightening locknut.
-
Install canopy (D) to collar loop (C) and secure with collar ring (E).
-
Install light bulbs into the sockets.
-
Install glass panels (L) & (O) to metal frame (K) and secure with rubber washers (M) and screws (N).
NOTE: Do not overtighten otherwise glass could become damaged. -
Determine desired overall length, and amount of chain (F) needed. Shorten chain using chain pliers. (Keep extra chain)
-
Attach chain (F) to collar loop (C) and fixture loop (H) using quick links (G). Secure quick links (G).
-
Thread fixture wire and ground wire through chain (F).
NOTE: When you reach collar loop (C), ensure there is no tension on the wires. Cut excess wires, being sure to leave about 12” to reach the junction box. -
Separate two sides of molded wire, and strip insulation on each 5/8″.
-
Loosen collar ring (E) and let canopy (D) slip down chain (F) carefully.
-
Twist all fixture wires together. Slip through center hole of collar loop (C).
NOTE: Untwist wires and separate to prepare for connection. -
Loosen cable lock and install to end of safety cable. Run safety cable through junction box and around structural member of building. Insert cable through cable lock and tighten the ends with a screwdriver to secure. (See diagram 1)
-
Connect fixture ground wire (bare copper) to the supply ground wire (usually green or bare copper) using wire nut (A).
NOTE: It is imperative that the fixture is grounded. -
Connect fixture neutral wire (ribbed) to the supply neutral wire (usually white) using wire nut (A).
-
Connect fixture hot wire (smooth with markings) to the supply hot wire (usually black) using wire nut (A).
CAUTION: Do not reverse the hot and neutral connections. -
Make sure all wire connections are tight, then carefully tuck into the junction box.
-
Install canopy (D) to collar loop (C) and secure with collar ring (E).
Care Instructions
Clean only with a soft dry cloth or feather duster. Do Not use abrasive or chemical agents.