classy leaves B099299PMF Bathroom Light Fixtures 2 Light Mason Jar Vanity Lights Instruction Manual

classy leaves B099299PMF Bathroom Light Fixtures 2 Light Mason Jar Vanity

Lights

Product Information

Specifications

• Mounting plate (B): 1 piece
• Green ground screw (C): 1 piece
• Back plate (E): 1 piece
• Screw (F): 4 pieces
• Lid (G): 2 pieces
• Jar (H): 2 pieces

Product Usage Instructions

Before starting assembly and installation, please prepare the needed tools as shown in the picture.

1. Carefully unpack the fixture and ensure all parts and accessories are included.
2. Turn off the power by switching off the main power switch in the fuse box and wall switch.
3. Remove screws (F) from the back plate (E) and detach the mounting plate assembly (B).
4. Attach the mounting plate assembly (B) to the outlet box using mounting screws (D) and pass wires through the centre.
5. Make wire connections following the provided chart and using plastic wire connectors (A).
6. Align the back plate (E) with the mounting plate (B) and secure with screws (F).
7. Install bulbs (not included) and thread jar (H) onto lid (G).
8. Check installation, then turn on the light and enjoy!

FAQ

• Q: Can I install the fixture myself without an electrician?
• A: We suggest installation by a licensed electrician to reduce the risk of fire, electric shock, or personal injury.
• Q: What should I do if I exceed the maximum wattage recommended on the socket?
• A: Please do not exceed the maximum wattage recommended on the socket to avoid damage or hazards.

Introductions

WARNING (To reduce the risk of fire, electric shock, or personal injury):

1. We suggest installation by a licensed electrician.
2. Please read the instruction carefully and save it as you may need it at a later time.
3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
   • A) Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
   • B) Place the wall switch in the “OFF” position.
4. Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
5. Make sure that the ceiling or wall can stand the weight of the lamp before installation.
6. Make sure the voltage you are using is 120V. The maximum wattage is 40W per bulb.
7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
8. When replacing bulb, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT

TOOLS REQUIRED (NOT INCLUDED)

• Before starting assembly and installation please prepare the needed tools as below picture

PARTS TYPE & QTY INCLUDING

• (B) Mounting plate (1)
• (C) Green ground screw (1)
• (E) Back plate (1)
• (F) Screw (4)
• (G) Lid (2)
• (H) Jar (2)

ACCESSORIES & QTY ENCLOSED

• (A) Plastic Wire Connectors (3)
• (D) Mounting screw (2)

ASSEMBLY & INSTALLATION INSTRUCTIONS

1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.

2. Turn off power
   Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.

   • A) Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
   • B) Place the wall switch in the “OFF” position.

3. Unscrew the screws (F) from the back plate (E) then carefully remove the mounting plate assembly (B).

• Attach the mounting plate assembly (B) to outlet box with mounting screws (D).
• Carefully and gently pass the outlet box wires through the center of the mounting plate assembly (B).

Make wire connections
Connect wires as below wires connecting shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE,
NEVER CONNECT OTHER WIRES TO GROUND WIRES.

Connect ground wires according to the below chart

Twist wires together with plastic wire connector (A) until tightly joined, then carefully tuck all wires into the outlet box.

NOTE: be sure that no wire strands are exposed.

• Align the holes in the back plate (E) and mounting plate (B), then attach the back plate (E) using the previously removed screws (F). Tighten until snug.

• Install bulbs (Not included) (Please do not exceed the maximum wattage recommended on the socket.) Thread the jar (H) onto the lid (G) till tight.

• Check everything is already installed properly, and then you can turn on the light. Enjoy!

CLEANING

• To clean, wipe the fixture with a soft cloth.
• Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper

ORDERING PARTS

• Keep this sheet for future reference in case you need to order replacement parts.
• All parts for this fixture can be ordered from the place of purchase.
• Be sure to use exact wording from illustration when ordering parts.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>