LINSY HOME LH096M1-A Electric Fireplace Instruction Manual

LINSY HOME LH096M1-A Electric Fireplace

Product Information

Specifications

• Product: Electric Fireplace LH096M1-A
• Dimensions: (W) 22.75 * (H) 19.61 inch
• Components:
  • Fireplace – Quantity: 1
  • Remote control – Quantity: 1
  • Instructions – Quantity: 1
• Electrical Parameters:
  • Rated Operating Voltage: 120V
  • Rated Operating Frequency: 60Hz
  • Rated Working Power: 1400W
  • Rated Power of Heating Element: 1350W
  • Product Net/Gross Weight: 8.9KG/10.5KG

Control Panel Functions

The control panel of the electric fireplace LH096M1-A consists of four keys and two 7-segment digital display tubes. The control mode includes power supply, heating, timing, and flame control.

Safety And Care Advice

Before starting the assembly process, please check if all the components and tools listed in the instruction manual are received. Remove all fittings from the plastic bags and separate them into homologous groups. Keep children and animals away from the working areas to avoid any potential harm. Ensure that there is enough space to lay out the parts before starting the assembly. Do not stand on the product to prevent damage. Assemble the product as close to its final position as possible. Avoid placing furniture directly in front of radiators, fires, or any other source of heat. The assembly process is easier with the help of two people. Dispose of all packaging carefully and responsibly.

Cold Climate Installation Recommendation

If installing the unit against a non-insulated exterior wall or chase, it is mandatory to insulate the outer walls to conform to applicable insulation codes. For electrical connection, the unit comes with a standard 6-foot (1.8M) three-wire cord that exits from the rear of the fireplace. Plan the installation to avoid the use  of an extension cord.

Cleaning and Maintenance

To clean the metal trim, use a soft cloth slightly dampened with citrus oil- based product and buff with a clean soft cloth. Do not use brass polish or household cleaners as they can damage the metal trim. Citrus oil-based products can be obtained at supermarkets or hardware stores. The motors used on the fan and flame generator assembly are pre-lubricated and do not require further lubrication. However, periodic cleaning/vacuuming of the fan/heater unit is  recommended. Ensure that the unit is turned off and unplugged before cleaning the heater or fireplace.

Electrical Repairs and Wiring

Any electrical repairs or rewiring of this unit should be carried out by a licensed electrician in accordance with national and local codes. When repairing or replacing any electrical component or wiring, follow the original wire routing, color coding, and securing locations. Ensure that the power is turned off before proceeding.

Product Usage Instructions

• Step 1: Unpacking
  Remove all packaging materials and check if you have all the components listed in the instruction manual.

• Step 2: Component Preparation
  Remove all fittings from the plastic bags and separate them into homologous groups. This will make the assembly process easier.

• Step 3: Safety Precautions
  Ensure that children and animals are kept away from the working areas to avoid any potential harm. Make sure you have enough space to lay out the parts before starting the assembly. Do not stand on the product to prevent damage.

• Step 4: Assembly
  Assemble the product as close to its final position as possible. If you are installing the unit against a non-insulated exterior  wall or chase, make sure the outer walls are insulated according to
  applicable insulation codes. Plan the installation to avoid the use of an extension cord.

• Step 5: Power Connection
  Use a dedicated socket for the electric fireplace and do not share it with other appliances. Do not use an extension cord or relocatable power tap (outlet/power strip).

• Step 6: Control Panel Functions
  Use the control panel to control the power supply, heating, timing, and flame settings. The control panel consists of four keys and two 7-segment digital display tubes.

• Step 7: Cleaning and Maintenance
  Clean the metal trim using a soft cloth slightly dampened with citrus oil- based product. Buff with a clean soft cloth. Avoid using brass polish or household cleaners as they can damage the metal trim. Periodically clean/vacuum the fan/heater unit, ensuring that the unit is turned off and unplugged before cleaning.

• Step 8: Electrical Repairs and Wiring
  If any electrical repairs or rewiring are required, contact a licensed electrician to carry out the work in accordance with national and local codes. Ensure that the power is turned off before proceeding.

• Step 9: Safety Precautions
  Do not use the fireplace if any part of it has been under water. Contact a qualified service technician to inspect the fireplace and replace any part of the electrical system.

FAQ (Frequently Asked Questions)

• Q: Can I use an extension cord with the electric fireplace?
  A: No, it is recommended to use a dedicated socket and avoid using an extension cord or relocatable power tap.

• Q: How should I clean the metal trim?
  A: Use a soft cloth slightly dampened with citrus oil-based product to clean the metal trim. Avoid using brass polish or  household cleaners as they can damage the metal trim.

• Q: Is lubrication required for the fan and flame generator assembly?
  A: No, the motors used on the fan and flame generator assembly are pre- lubricated and do not require further lubrication.

• Q: Can I repair or rewire the electric fireplace myself?
  A: No, any electrical repairs or rewiring should be carried out by a licensed electrician in accordance with national and local codes.

Components

Please check you have all the pieces listed below.

Pieces List

Important – Please read these instructions fully before starting assembly.

Electrical parameters

Rated operating voltage| 120V| Rated working power| 1400W
Rated operating frequency| 60Hz| Rated power of heating element| 1350W
3A Package Size| 675192581MM| Product net/gross weight| 8.9KG/10.5KG

Control mode

Control panel functions

| Power supply, heating, timing, flame 4 keys, Add 2-7 segment digital display tubes

Control panel Diagram

Safety And Care Advice

Important – Please read these instructions fully before starting assembly.

• Please check if all the components and tools listed on pages 3 – 4 are received.
• Please remove all fittings from the plastic bags and separate them into homologous groups.
• Please keep children and animals away from the  working areas; swallow small parts may cause suffocation.
• Please make sure you have enough space to lay out the parts before starting.
• Do not stand on the product, which could cause damage.
• Please assemble the product as close toits final position as possible.
• Do not place furniture directly in front of radiators, fires, or any other source of heat.
• The assembly will be easier with 2 people.
• Please dispose of all packaging carefully and responsibly.

General care and maintenance.

• Important – Please read these instructions fully before starting assembly.
• Please clean with a damp cloth or mild detergent, do not use bleach or abrasive cleaners.
• Do not allow the spill to stay on the surface for a long time.
• Do not clean with products containing the following: acetone (e.g., nail varnish remover), ammonia (e.g.bleach), or sodium hydroxide(e.g., caustic soda, drain, and oven cleaners).
• If the product is accidentally exposed to the irritating liquid, rinse thoroughly with clean wa.ter
• Mats can be used to protect surfaces from moisture and heat.
• Please check whether there are missing screws in the product regularly.
• The product should not be discarded with household waste, and please take it to your local authority waste disposal center.

Important – Please read these instructions fully before starting assembly.

• Do not share a socket with other appliances when using electric fireplaces, please use a dedicated socket
• Never use with an extension cord or relocatable power tap (outlet / power strip).

Important – Please read these instructions fully before starting assembly.

COLD CLIMATE INSTALLATION RECOMMENDATION:
When installing this unit against a Non-insulated exterior wall or chase, it is mandatory that outer walls be insulated to conform to applicable insulation codes.

ELECTRICAL CONNECTION
The unit comes standard with 6 feet (1.8M) three wire cord, exiting from the rear of the fireplace. Plan the installation to avoid the use of an extension cord.

CLEANING TRIM
Clean the metal trim using a soft cloth, slightly dampened with citrus oil based product and buff with a clean soft cloth.
DO NOT use brass polish or household cleaners as these products will damage the metal trim.
Citrus oil-based products can be obtained at supermarkets or hardware stores.

MAINTENANCE
The motors used on the fan and the flame generator assembly are pre-lubricated for extended bearing life and require no further lubrication. However, periodic cleaning/vacuuming of the fan/ heater unit is recommended. Make sure the unit is turn OFF and unplugged whenever you are cleaning the heater of fireplace.

• WARNING: Make sure the power is turned off before proceeding. Any electrical repairs or rewiring of this unit should be carried out by a licensed electrician in accordance with national and locate codes. If repairing or replacing any electrical component or wiring, the original wire routing, color coding and securing locations must be followed.

• WARNING: Electric outlet wiring must comply with local building codes and other applicable regulations to reduce risk of fire, electric shock and injury to persons.

• WARNING: Do not use this fireplace if any part of it has been under water.
  Immediately call a qualified service technician to inspect the fireplace and replace any part of the electrical system.

• WARNING: Disconnect power before attempting any maintenance or cleaning to reduce the risk of fire, electrical shock or personal injury.

• WARNING: During any service of this appliance, the power to the unit must be  turned off, Always remember to remove the electrical plug from the wall outlet.

Assembly Instructions

Important – Please read these instructions fully before starting assembly.
Position your completed mantel close to its final location. Make sure you can access the back of the mantel as your electric fireplace appliance will be installed from back.

• Position your completed mantel close to its final location. Make sure you can access the back of the mantel as your electric fireplace appliance will be installed from back.
• Using a Phillips head screwdriver, remove the screws and the metal mounting center opening. Next unpack the electric fireplace appliance carefully. Position the appliance behind the fireplace with front facing the wood mantel. With the help of an adult assistant, lift the appliance and gently slide it into the opening in the mantel. Make sure the appliance is centered left and right in the opening. Be careful when placing appliance and adjusting, bottom of appliance could scratch the finish of the base/hearth of your fireplace. Re-attach the mounting brackets with the Phillips head screwdriver, and supplied screws.
• DO NOT OVER TIGHTEN. With the help of an assistant, carefully lift completed unit and place it with the front facing out in the final location you have chosen for your fireplace. Make sure to secure the electrical cord before lifting or moving completed fireplace. When choosing a final location, make sure you will have clear access to grounded electrical outlet.

Important – Please read these instructions fully before starting assembly.

This heater is for use on 120 volts. The cord has a plug as shown at (A) in figure 2. An adapter as shown at (C) is available for connecting three-blade grounding-type plugs to two-slot receptacles. The green grounding lug extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box. The adapter should not be used if a three-slot grounded receptacle is available.
NOTE : Adapters are NOT for use in Canada

Functional Requirements

Power Key

| 1. Turn on or Turn off the machine
---|---
2. This key has the same highest priority as the POWER key on the remote control (compared with FLAME,HEATER,TIMER).
3. This key has a memory function. Its function is to remember the current state (except the timing function) and turn off all the currently opened functions. Pressing this key again

will restore the state set before turning off.

4. If all functions of the machine are turned off through this key, the machine cannot be turned on by pressing other keys.
5. If the function of the whole machine is turned off after the time setting is completed, this key must also be pressed to start the machine.

Heater

| 1. This key is a heating function key to turn on and off. When the heating function is turned on, the heating wire starts to work after the fan is turned on for 5 seconds. When turning off the heating function, the heating wire need to be turned off first, and the fan will turn off after

8 seconds.

2. The default unit is ℉.
3. Temperature adjustment mode: When the HEATER is turned on, press and hold the HEATER key for 5 seconds to enter the temperature adjustment mode. When entering the temperature adjustment mode, the monitor will flash all the time (the on-off time is 0.5 seconds each).

At this time, you can press the HEATER key. To set the temperature value required by the user.       The temperature can be adjusted at Fahrenheit：72℉/74℉/76℉/78℉/82℉/ON/64℉/66℉/72℉ or at Celsius: 22℃/23℃/24℃/25℃/26℃/27℃/ON/18℃/19℃/20℃/22℃. After the setting is completed, the temperature adjustment mode will automatically exit after 5 seconds.

4. When setting the temperature, the monitor will display the corresponding set value according to the user’s setting. When it is normally open, the monitor will be displayed as ON, but not when it is OFF.
5. After the monitor shows temperature, if there is no action within 10 seconds, the monitor will be turned off.
6. Degree-unit Switching Function: when the HEATER is turned on, press and hold the POWER key for 5 seconds, and the current degree-unit will flash for 3 times. (The on-off time is 0.5 seconds each). After the flash, it will switch to another unit.
7. Lock the Heating Function: When the machine is powered on, press and hold the HEATER key for 10 seconds, and the bottom gray light will flash six times (the on and off times are respectively 0.3 seconds) to inform the user that the lock is successful.
8. Unlock the Heating Function: when the heating is locked, press and hold the HEATER key for 10 seconds, and the bottom gray light will flash for 6 times (the on-off time is respectively 0.3 seconds), to inform the user that the lock heating function has been unlocked. At this time, press the HEATER key again, and the heating function will be turned on.
9. If the bottom gray lamp is turned off before turning on the heating function, the bottom gray lamp will be slightly bright after turning on the heating function. Synchronous motor does not operate.
10. When the machine is powered on and the heating function is turned on for the first time, the degree-unit is set to 82℉ by default.

Important – Please read these instructions fully before starting assembly.

Timer

| 1. This key is the function key for setting the timed shutdown, and the automatic shut down time can be set circularly between 1h to 8h and OFF.
---|---
2. Set the timing time by adjusting the key. In the setting timing state, the monitor will display the corresponding value according to the user’s setting, with 1 hour displayed  as 1h, 2 hours displayed as 2h, and so on.
3. After the timing is set, if the power key is pressed, the set time will be cleared and the memory mode will be entered.

Flame

| 1.This key simultaneously adjusts the brightness of flame and bottom ash.
2. The brightness level sequence is L4-L3-L2-L1-OFF, and so on. When the flame lamp is OFF, the synchronous motor stops working.
3. When setting, the monitor will display the corresponding value according to the user’s setting, but it will not be displayed when OFF.

Malfunction Alarm

| E1: the temperature control device detects that the internal temperature of the machine exceeds 140℉ (60℃) degrees.
E2: NTC is defective and the temperature sensor damaged.
E3: The heater is not working.

The Malfunction Alarm flashes for 5 times and then lights up, and disappears after 10 seconds of inactivity. At this time, when pressing the Heater, the fault code will light up directly (without heating), and it needs to be reset after power failure. Other functions are in normal use.

Remote control illustration

Power key

| 1. Control the opening and closing of the machine
---|---
2. This key has the same highest priority as the POWER key on the machine (compared with FLAME, HEATER, TIMER)
3.This key has a memory function. Its function is to remember the current state (except the timing function) and turn off all currently enabled functions. Pressing this key again will restore the setting state before turning off.
4.If you use this key to turn off all functions of the machine, you cannot turn on the machine by pressing other keys.
5.If the whole machine function is turned off after the timing shutdown setting is completed, you must press this key to start the machine.
6.The POWER key on the remote control does not have the function of switching heating temperature units.
Flame key

|

Same as key board.

Heating key

|

Only the heating function is turned on and off.

Timing key

|

Same as key board.

Gear cycle key

|

When heating is turned on, press the gear cycle key to enter the temperature regulation mode and adjust the set temperature

Remote control illustration

|

Important – Please read these instructions fully before starting assembly.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>