Altronix WPTV248300UL Series CCTV Power Supply, Outdoor, 8 Fused Installation Guide

Altronix WPTV248300UL Series CCTV Power Supply, Outdoor, 8 Fused

Overview

WPTV248UL Series outdoor CCTV Power Supplies provide power via eight (8) fused or PTC protected outputs for CCTV Cameras, heaters, and other video accessories. Units are UL Listed UL 2044 “U.S. and Canada for CCTV Equipment.”

Eight (8) Output WPTV Reference Chart

Altronix

Model Number

| ****

Output Voltage

| Total Output Current (Power)| Number of Outputs| PTC Protected Outputs (Class 2 power-limited for Dry locations, Class 3 for Wet locations).| Fuse Protected Outputs| Individual Output Current (max per output – not to exceed total output current)| Fuse Ratings| Main Fuse Ratings| ****

Primary In-line Fuse Ratings

| 115VAC 50/60Hz Input Current| ****

Agency Listings

---|---|---|---|---|---|---|---|---|---|---|---
WPTV248UL| 24VAC| 3.5A| 8| –| ✓| 3.5A| 3.5A| 5A/

250V

| 3.5A/

250V

| 0.9A| ****

28VAC| 3A
WPTV248ULCB| 24VAC| 3.5A| 8| ✓| –| 2.5A| –| 5A/

250V

| 3.5A/

250V

| 0.9A
28VAC| 3A
WPTV248175UL| 24VAC| 7A| 8| –| ✓| 3.5A| 3.5A| 10A/

250V

| –| 1.76A
28VAC| 6.25A
WPTV248175ULCB| 24VAC| 7A| 8| ✓| –| 2.5A| –| 10A/

250V

| –| 1.76A
28VAC| 6.25A
WPTV248300UL| 24VAC| 12.5A| 8| –| ✓| 3.5A| 3.5A| 15A/

32V

| –| 2.7A
28VAC| 10A
WPTV248300ULCB| 24VAC| 12.5A| 8| ✓| –| 2.5A| –| 15A/

32V

| –| 2.7A
28VAC| 10A

Specifications

Agency Listings:

• UL Listed for Commercial CCTV Equipment (UL2044).
• cUL Listed – CSA Standard C22.2 No.1-98, Audio, Video and Similar Equipment.
• CE European Conformity

Input:

115VAC, 50/60Hz.

Output:

• Eight (8) fuse or PTC protected outputs.
• 24VAC or 28VAC.
• Outputs are rated @ 3.5A (fused) or 2.5A (PTC).
• Surge suppression.

Features

• Secondary fuse rated @ 5A/250V.
• AC power LED.
• Unit maintains camera synchronization.
• Ease of installation saves time & eliminates costly labor.
• Spare fuses provided. (all models w/primary and/or secondary fuses).
• NEMA 4 Rated enclosure for outdoor use.

Enclosure Dimensions (H x W x D approx.):

12” x 8” x 6” (304.8mm x 203.2mm x 152.4mm).

Installation Instructions

Unit should be installed in accordance with The National Electrical Code and all applicable Local Regulations.

1. Remove back plate inside the enclosure by removing four (4) mounting screws (Figs. 2a-7a, pgs. 5-10 ).

2. Mark and drill desired knockouts on the enclosure to facilitate wiring. For suggested wire entry locations refer to Fig. 1, pg. 4. Use weather tight NEMA 4 rated connectors, bushings, and cables.

3. Unit can be wall or pole mounted.
   Wall Mount:

   • Mark and drill holes to line up with the top and bottom holes of the enclosure flange.

   • Secure enclosure with appropriate fasteners (Fig. 9 and Fig. 9a, pg. 11).
     Pole Mount:

   • Refer to the detailed pole mount instructions (pg. 11). Secure enclosure to earth ground.

4. . Set power switch on power distribution board marked [PD] to OFF position for models WPTV248UL or WPTV248ULCB (Figs. 2b, 3b, pgs. 5, 6). Set power disconnect circuit breaker to OFF position for all other models (Figs. 4b-7b, pgs. 7-10).

5. All units are factory set for 24VAC operation.
   For 28VAC operation adjust unit prior to mounting and applying power as follows:
   Change the wire position so that the black wire [28V] is connected to the terminal marked [P] and the yellow wire [24V] is connected to the terminal marked [S].
   Note: WPTV248ULCB set for 28VAC operation is not Class 2, not power- limited.

6. Place back plate with all internal parts, using four (4) screws, back into WP enclosure (Figs. 2a-7a, pgs. 5-10).

7. Connect AC power to the black and white flying leads of the transformer(s) (Figs. 2-7, pgs. 5-10), secure green lead to earth ground. Use 18 AWG or larger for all power connections. Keep power-limited (PTC protected outputs only) wiring separate from non power-limited wiring. Minimum 0.25” spacing must be provided. Use separate entries.

8. Set power switch on power distribution board marked [PD] to ON position for models WPTV248UL or WPTV248ULCB (Figs. 2b, 3b, pgs. 5, 6). Set power disconnect circuit breaker to ON position for all other models (Figs. 4b-7b, pgs. 7-10).

9. Measure output voltage before connecting devices. This helps avoiding potential damage. Terminals marked [1P – 8P] are of the same polarity.
   CAUTION: Determine the maximum operating voltage of the equipment being powered before adjusting the output voltage.

10. Set power switch on power distribution board marked [PD] to OFF position for models WPTV248UL or WPTV248ULCB (Figs. 2b, 3b, pgs. 5, 6). Set power disconnect circuit breaker to OFF position for all other models (Figs. 4b-7b, pgs. 7-10).

11. Connect devices to terminals marked [1P – 1N] through [8P – 8N] on PD8/PD8CB board (Figs. 2-7, pgs. 5-10), carefully observing polarity.

12. Set power switch on power distribution board marked [PD] to ON position for models WPTV248UL or WPTV248ULCB (Figs. 2b, 3b, pgs. 5, 6). Set power disconnect circuit breaker to ON position for all other models (Figs. 4b-7b, pgs. 7-10).

13. Green LED will illuminate when power is present.

14. Upon completion of wiring, secure enclosure door with the cam lock (supplied).
    Caution: Equipment to be installed/serviced by authorized/trained personnel only.
    Shut branch circuit power before installing/servicing equipment.

WARNING:
This installation should be made by qualified service personnel. Unit should be installed in accordance with the National Electrical Codes and all local codes. For continued protection against risk of fire replace all fuses only with the same type and rating (3.5A/250VAC).

Terminal Identification

PD8 – Power Distribution Module

Wall Mount Installation

Place unit at desired location and secure with mounting screws (not included) (Fig. 8, pg. 11).

Pole Mounting Using Optional Pole Mount Kit PMK1 (not included):
This installation should be made by qualified service personnel. This product contains no serviceable parts. PMK1 is intended for use with Altronix outdoor rated power supplies or accessories housed in WP1, WP2, WP3 and WP4 enclosures. Brackets are designed for use with the Wormgear Quick Release Straps (two included).

1. Thread one (1) wormgear quick release strap through the slots on the back of a mounting bracket (Fig. 5, pg. 11).
2. Once the desired height of the top Pole Mount bracket is achieved, tighten the straps down by sliding open end of the strap through the locking mechanism on the strap, then tighten the screw with flat head screwdriver or 5/16” hex socket driver (Fig. 10, pg. 11 and Fig. 12, pg. 11). 
3. Attach the bottom bracket to the enclosure by inserting bolts through the flange of the enclosure and into the bracket, tightening bolts with a 7/16” hex socket (Fig. 11, pg. 11).
4. Thread the second wormgear quick release strap through the slots on the back of the bottom mounting bracket (Fig. 9, pg.11).
5. Mount enclosure onto the top bracket by inserting bolts through flange of the enclosure and into the bracket, tightening bolts with a 7/16” hex socket (Fig. 11, pg. 11).
6. Tighten the straps of the bottom bracket down by sliding the open end of the strap through the locking mechanism on the strap, then tighten screw with flat head screwdriver or 5/16” hex socket driver (Fig. 9, pg. 1).
7. Clip excess straps. 

Enclosure Dimensions (H x W x D approximate)

12” x 8” x 6” (304.8mm x 203.2mm x 152.4mm)

Altronix is not responsible for any typographical errors.
140 58th Street, Brooklyn, New York 11220 USA | phone: 718-567-8181 | fax: 718-567-9056 website: www.altronix.com | e-mail: info@altronix.com | Lifetime Warranty
IIWPTV248UL Series H20U

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>