VISUAL COMFORT S 2197 Halle Large Narrow Wall Lantern Instruction Manual

VISUAL COMFORT S 2197 Halle Large Narrow Wall Lantern

Product Information

The Halle Large Narrow Wall Lantern, Item # S 2197 is a light fixture suitable for outdoor/wet location installation. It comes with a mounting plate (B), fixture body (G), lantern (I), glass panels (J) & (K) & (L), metal tabs (M), screws (N), and other required hardware for installation. The light bulb is not included in the package. The light fixture should be installed in accordance with all applicable, local installation codes by a person familiar with the construction and operation of it.

Product Usage Instructions

1. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
2. Carefully remove all parts from the box. Place on a clean, soft surface.
3. Remove mounting plate (B) from fixture body (G) by removing side screws (F).
4. Remove lantern (I) from fixture body (G) by removing side screws (H).
5. Using the mounting plate (B) as a guide, line up with the junction box and mark anchor positions.
6. Using a drill bit slightly smaller than the anchor, drill holes in the marked positions. Install anchors (A) into holes using the hammer.
7. Install mounting plate (B) to junction box and secure with mounting screws (D), then secure wood screws (C) to anchors (A).
8. Run support cable through hole on back of mounting plate (B). Wrap the support cable around the saddle (a), and secure with u-bolt (b) and hex nuts (c). (See diagram 1)
9. Wrap fixture ground wire (green) around the green grounding screw (see diagram 2). Tighten. Continue fixture ground wire and connect to supply ground wire (usually green or bare copper) using wire nut (E). NOTE: It is imperative that the fixture is grounded.
10. Connect fixture neutral wire (white) to the supply neutral wire (usually white) using wire nut (E).
11. Connect fixture hot wire (black) to the supply hot wire (usually black) using wire nut (E). CAUTION: Do not reverse the hot and neutral connections.
12. Make sure all wire connections are tight, then carefully tuck into the junction box.
13. Install fixture body (G) to mounting plate (B) and secure with side screws (F).
14. Remove metal tabs (M) from lantern (I) by unscrewing screws (N), then install glass panels (J) & (K) & (L) to lantern (I) and secure with metal tabs (M) using screws (N). NOTE: Do not over-tighten otherwise shade could become damaged.
15. Install light bulb into the socket.
16. Install lantern (I) to fixture body (G) and secure with side screws (H).
17. For outdoor/wet location installation, using silicon compound, apply a small bead where backplate meets the wall to prevent water from entering. NOTE: Large gaps will need to be corrected before applying silicon compound.

Halle Large Narrow Wall Lantern
Item # S 2197

NOTICE: This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.

TOOLS REQUIRED (NOT INCLUDED):

• Phillips Screwdriver
• Hammer
• Slotted Screwdriver
• Pencil
• Drill

INSTALLATION INSTRUCTIONS

1. Carefully remove all parts from the box. Place on a clean, soft surface.

2. Remove mounting plate (B) from fixture body (G) by removing side screws (F).

3. Remove lantern (I) from fixture body (G) by removing side screws (H).

4. Using the mounting plate (B) as a guide, line up with the junction box and mark anchor positions.

5. Using a drill bit slightly smaller than the anchor, drill holes in the marked positions. Install anchors (A) into holes using the hammer.

6. Install mounting plate (B) to junction box and secure with mounting screws (D), then secure wood screws (C) to anchors (A).

7. Run support cable through hole on back of mounting plate (B). Wrap the support cable around the saddle (a), and secure with u- bolt (b) and hex nuts (c). (See diagram 1)

8. Wrap fixture ground wire (green) around the green grounding screw (see diagram 2). Tighten. Continue fixture ground wire and connect to supply ground wire (usually green or bare copper) using wire nut (E).
   NOTE : It is imperative that the fixture is grounded.

9. Connect fixture neutral wire (white) to the supply neutral wire (usually white) using wire nut (E).

10. Connect fixture hot wire (black) to the supply hot wire (usually black) using wire nut (E).
    CAUTION : Do not reverse the hot and neutral connections.

11. Make sure all wire connections are tight, then carefully tuck into the junction box.

12. Install fixture body (G) to mounting plate (B) and secure with side screws (F).

13.  Remove metal tabs (M) from lantern (I) by unscrewing screws (N), then install glass panels (J) & (K) & (L) to lantern (I) and secure with metal tabs (M) using screws (N).
    NOTE : Do not over-tighten otherwise shade could become damaged.

14. Install light bulb into the socket.

15. Install lantern (I) to fixture body (G) and secure with side screws (H). FOR OUTDOOR/WET LOCATION INSTALLATION:

16. Using silicon compound, apply a small bead where backplate meets the wall to prevent water from entering.
    NOTE : Large gaps will need to be corrected before applying silicon compound.

Care Instructions

Clean only with a soft dry cloth or feather duster. Do not use abrasive or chemical agents.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>