VISUAL COMFORT KW5642AI Brassica Large Linear Chandelier Instruction Manual

Brassica Large Linear Chandelier
Item # KW 5642
Instruction Manual

ASSEMBLY INSTRUCTIONS

Option 1: Canopy Mounted Driver NOTICE:
This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
TOOLS REQUIRED (NOT INCLUDED):

1. Carefully remove all parts from the box. Place on a clean, soft surface.

2. Remove mounting plate (A) from canopy (G) by removing collar ring (H).

3. Install mounting plate (A) to the junction box and secure with mounting screws (D).

4. Feed electrical wires through bottom rod (K) and connect to fixture (L). Repeat for middle rod (J), connecting to bottom rod (K).

5. Continue feeding wire through collar ring (H), canopy (G) and top rod (I).

6. Holding fixture upright, slide collar ring (H) and canopy (G), down and rest on middle rod (J). Then connect top rod (I) to middle rod (J).
   NOTE: Slide components down slowly to avoid damages.

7. Hang fixture swivel ball (F) to the center of mounting plate (A) and secure with set screw (E) using provided wrench. See diagram 1.

8. Cut excess wires, being sure to leave enough to reach the junction box. Separate wires, and strip insulation on each 5/8″.

9. Connect supply ground wire (usually green or bare copper) around the green grounding screw (see diagram 2). Tighten
   NOTE: It is imperative that the fixture is grounded.

10. Connect driver (C) input neutral wire (white) to the supply neutral wire (usually white) using wire nut (B).

11. Connect driver (C) input hot wire (black) to the supply hot wire (usually black) using wire nut (B).
    CAUTION: Do not reverse the hot and neutral connections.

12. Connect fixture neutral wire (black) to driver (C) output wire (black) using wire nut (B).

13. Connect fixture hot wire (red) to driver (C) output wire (red) using wire nut (B).
    CAUTION: Do not reverse the hot and neutral connections.

14. Make sure all wire connections are tight, then carefully tuck into the junction box.

15. Insert driver (C) into mounting plate bracket.

16. Install canopy (G) to mounting plate (A) and secure with collar ring (H).
    Care Instructions: Clean only with a soft dry cloth or feather duster. Do not use abrasive or chemical agents.

Option 2: Ceiling Mounted Driver

1. Carefully remove all parts from the box. Place on a clean, soft surface.

2. Place driver (C) into ceiling and route all wires through one of the knockouts in the junction box.

3. Remove mounting plate (A) from canopy (G) by removing collar ring (H).

4. Install mounting plate (A) to the junction box and secure with mounting screws (D).

5. Feed electrical wires through bottom rod (K) and connect to fixture (L). Repeat for middle rod (J), connecting to bottom rod (K).

6. Continue feeding wire through collar ring (H), canopy (G) and top rod (I).

7. Holding fixture upright, slide collar ring (H) and canopy (G), down and rest on middle rod (J). Then connect top rod (I) to middle rod (J).
   NOTE: Slide components down slowly to avoid damages.

8. Hang fixture swivel ball (F) to the center of mounting plate (B) and secure with set screw (E) using provided wrench. See diagram 1.

9. Cut excess wires, being sure to leave enough to reach the junction box. Separate wires, and strip insulation on each 5/8″.

10. Connect supply ground wire (usually green or bare copper) around the green grounding screw (see diagram 2). Tighten
    NOTE: It is imperative that the fixture is grounded.

11. Connect fixture neutral wire (black) to driver (C) output wire (black) using wire nut (B).

12. Connect fixture hot wire (red) to driver (C) output wire (red) using wire nut (B).

13. Connect supply ground wire (usually green or bare copper) around the green grounding screw (see diagram 2). Tighten.
    NOTE: It is imperative that the fixture is grounded.

14. Connect driver (C) input neutral wire (white) to the supply neutral wire (usually white) using wire nut (B).

15. Connect driver (C) input hot wire (black) to the supply hot wire (usually black) using wire nut (B).
    CAUTION: Do not reverse the hot and neutral connections.

16. Make sure all wire connections are tight, then carefully tuck into the junction box.

17. Install canopy (G) to mounting plate (A) and secure with collar ring (H).
    Care Instructions: Clean only with a soft dry cloth or feather duster. Do not use abrasive or chemical agents.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>