VISUAL COMFORT PCD 5215 Orsay Medium 3-Light Linear Chandelier Instruction Manual
- October 30, 2023
- VISUAL COMFORT
Table of Contents
VISUAL COMFORT PCD 5215 Orsay Medium 3-Light Linear Chandelier
This is an elegant and modern chandelier that adds a touch of sophistication to any room. It comes with three bulbs included and has a linear design that makes it perfect for installation over a dining table or kitchen island. The chandelier is designed to be installed by a professional who is familiar with the construction and operation of the fixture, as well as the hazards involved.
Assembly Instructions
- Carefully remove all parts from the box. Place on a clean, soft surface.
- Remove mounting plate (A) from canopy (D) by removing collar ring (E).
- Install mounting plate (A) to the junction box and secure it with mounting screws (C).
- Feed electrical and ground wires through the bottom rod (H) and connect.
- Attach bottom rod (H) to mounting plate (A) using threaded rod couplings (F).
- Attach middle rod (I) to bottom rod (H) using threaded rod couplings (F).
- Attach top rod (G) to middle rod (I) using threaded rod couplings (F).
- Attach the fixture loop (K) to the top rod (G).
- Attach the chandelier arms to the fixture loop (K).
- Connect fixture ground wire (green or bare copper) to the supply ground wire using wire nut (B).
- Connect the fixture neutral wire (white) to the supply neutral wire (usually white) using wire nut (B).
- Connect the fixture hot wire (black) to the supply hot wire (usually black) using wire nut (B). CAUTION: Do not reverse the hot and neutral connections.
- Make sure all wire connections are tight, then carefully tuck them into the junction box.
- Install canopy (D) to mounting plate (A) and secure with collar ring (E).
- Install light bulb into the socket by lining up the base to holes and twisting to secure it.
- Threaded diffusers (J) on socket bases.
Care Instructions
Clean only with a soft dry cloth or feather duster. Do not use abrasive or chemical agents.
ASSEMBLY INSTRUCTIONS
Orsay Medium 3-Light Linear Chandelier Item # PCD 5215
NOTICE:
This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
TOOLS REQUIRED (NOT INCLUDED):
- Phillips
- Screwdriver
- Slotted
- Screwdriver
- Wire
- Cutters
- Wire
- Strippers
USING INSTRUCTIONS
- Carefully remove all parts from the box. Place on a clean, soft surface.
- Remove mounting plate (A) from canopy (D) by removing collar ring (E).
- Install mounting plate (A) to the junction box and secure with mounting screws (C).
- Feed electrical and ground wires through the bottom rod (H) and connect to the fixture body (I). Repeat for middle rod (G), connecting to bottom rod (H).
- Continue feeding wires through collar ring (E) and canopy (D).
- Holding fixture upright, slide collar ring (E) and canopy (D) down and rest on fixture body (I). Then connect top rod (F) to middle rod (G).
- NOTE: Slide components down slowly to avoid damage.
- Hang fixture swivel ball (K) to the center of mounting plate (A).
- Cut excess wires, being sure to leave enough to reach the junction box. Separate wires, and strip insulation on each 5/8”.
- Wrap fixture ground wire (bare copper) around the green groundingscrew (see diagram 1). Tighten. Continue fixture ground wire and connect to supply ground wire (usually green or bare copper) using wire nut (B).
- NOTE: It is imperative that the fixture is grounded..
- Connect fixture neutral wire (white) to the supply neutral wire (usuallywhite) using wire nut (B).
- Connect fixture hot wire (black) to the supply hot wire (usually black) using wire nut (B).
- CAUTION: Do not reverse the hot and neutral connections.
- Make sure all wire connections are tight, then carefully tuck into the junction box.
- Install canopy (D) to mounting plate (A) and secure with collar ring (E).
- Install light bulb into the socket by lining up base to holes and twisting to secure.
- Threaded diffusers (J) on socket bases. Care Instructions: Clean only with a soft dry cloth or feather duster. Do Not use abrasive or chemical agents.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>