V-TAC VT-3618 Smart Magnetic Linear Spot Light Instruction Manual

VT-3618 Smart Magnetic Linear Spot Light

Product Information

• Product Name: Smart Magnetic Linear Spot Light
• Model: VT-3618
• Lumens: 1500LM
• Power: 18W
• Beam Angle: 30 degrees
• CRI: >90
• Body Type: Aluminum
• Input Voltage: DC 48V
• Works with Assistant
• WEEE Number: 80133970

Product Usage Instructions

Installation Instructions

1. Make sure to turn off the power before starting the installation.
2. Install the luminaire into the guide rail groove.
3. Check that everything is in order.
4. Switch on the power if above steps done properly without any mistakes.

App Installation Instructions

1. Scan the given QR code, or download V-TAC Smart Light’ from the App Store (iOS) or the Google Play Store (Android).
2. Open the V-TAC Smart Light app and tap on register for creating a new account.
   • A) Mobile Number: Select the country, then enter your mobile number. Once done, tap `Next’.
   • B) E-Mail: Enter your email id and tap on `Next’.
3. Enter the verification code which will be sent to your mobile number/email id, then assign a new password to your account and tap on Confirm.
4. Tap on `Add Device’ or the + sign. Make sure the lamp is switched on.
5. Select the Wi-Fi network and enter the password.
6. Once you have successfully completed all steps, you will be redirected to a page where the App searches, registers, and initializes the device(lamp).
7. Once your device is successfully added, rename the device to your preference.

Alexa Settings Instructions

1. Install the Amazon Alexa app via the App Store(iOS) or the Play Store (Android) and register. If you already have an existing account with Amazon Alexa, please proceed to logging in.
2. Search for `V-TAC Smart Light’ on the Skills & Games page.
3. Enable the Skill.
4. Enter your V-TAC Smart Light login ID and password and tap on Link Now.
5. Discover your smart device on Alexa. Once you have enabled the skill, use voice command “Alexa discover devices” to add the device. You can also manually add the device by tapping on “Add device” and selecting the device.

Note: Discovering the device must be done every time the device’s name is changed on the app.

TECHNICAL DATA

INTRODUCTION & WARRANTY

Thank you for selecting and buying MAGNETIC SMART TRACKLIGHT V-TAC will serve you the best. Please read these instructions carefully before starting the installation and keep this manual handy for future reference. If you have any other query, please contact our dealer or local vendor from whom you have purchased the product. They are trained and ready to serve you at the best. The warranty is valid for 3 years from the date of purchase. The warranty does not apply to damage caused by incorrect installation or abnormal wear and tear. The company gives no warranty against damage to any surface due to incorrect removal and installation of the product. The products are suitable for 10-12 Hours Daily operation. Usage of product for 24 Hours a day would void the warranty. This product is warranted for manufacturing defects only.

MULTI-LANGUAGE MANUAL QR CODE
Please scan the QR code to access the manual in multiple languages.

WARNING

1. Please make sure to turn off the power before starting the installation.
2. Installation must be performed by a certified person.
3. Proper grounding should be ensured throughout the installation.
4. For Indoor use only

Caution, risk of electric shock.

This marking indicates that this product should not be disposed  of with other household wastes.

RoHS CE UKCA

INSTALLATION INSTRUCTION

1. Switch off the power.
2. Install the luminaire into the guide rail groove .
3. Check that everything is in order.
4. Switch on the power if above steps done properly without any mistakes.

APP INSTALLATION

Step 2: Scan the given QR code, or download “V-TAC Smart Light’ from the App Store (iOS) or the Google Play Store (Android).

For ANDROID For IOS

Step 3: Open the V-TAC Smart Light app and tap on register for creating a new account.

Step 4:

• Mobile Number: Select the country, then enter your mobile number. Once done, tap ‘Next’.
• E-Mail: Enter your email id and tap on ‘Next’.

Step 5: Enter the verification code which will be sent to your mobile number/email id, then assign a new password to your account and tap on “Confirm”.

Step 6: Tap on ‘Add Device’ or the + sign. Make sure the lamp is switched on.

Step 7: Choose ‘Lighting’ to start pairing the light to the app.

Step 8: To pair the device with LED Smart Strip Light make sure the light is blinks rapidly. Once the light blinks rapidly, the light is in pairing mode. If the light is not blinking rapidly, you can do one of the following steps:

• A. Switch the light on & off repeatedly for 3 times, with short intervals of less than 2 seconds.
• B. Tap the ‘How to make light blink rapidly’ link (as shown on the image to the right)
• C. You can also enable pairing mode from the Wi-Fi controller. Press and hold the ON/OFF button for 5-7 seconds and wait till you observe the light flashing. Please refer to the instruction section “WI-FI CONTROLLER FUNCTIONS”

Network Modes:

1. Smart Mode: Light flashes rapidly.
2. AP mode: Slow flash, once every 2 seconds.
   Confirm if the light blinks rapidly, select the Wi-Fi network, and enter the password.

Step 9: Once you have successfully completed step 8, you will be redirected to below page, where the App searches, registers and initializes the device(lamp) (ref image below)

Step 10: Once your device is successfully added, rename the device to your preference.

Step 11: After successfully pairing the Wi-Fi receiver with the app, you can start controlling multiple features of the lamp through your mobile– on/off switch, timing & schedules, and more.

ALEXA SETTINGS

Step1: Install the Amazon Alexa app via the App Store(iOS) or the Play Store (Android) and register. If you already have an existing account with Amazon Alexa, please proceed to logging in.

Step2: Once you are on the Amazon Alexa home page, tap on the lower right icon –– where the arrow is pointed–– to add a new device and skill.

Step3: Tap on settings and tap on “skills and games” as shown below.

Step4: Search for ‘V-TAC Smart Light’ on the “Skills & Games” page as shown below.

Step5: Enable the Skill.

Step6: Enter your V-TAC Smart Light login ID and password and tap on “Link Now”

Step7: Once you tap on Link Now, you will be redirected to a new page requesting for authorization(Ref Image below).
Tap on “Authorize”

Step8: You will receive confirmation of the account being linked successfully
(Ref Image below)

Step9: Discover your smart device on Alexa. Once you have enabled the skill

• You can use voice command ”Alexa discover devices” to the Alexa device which you have.
• To add device manually on home page tap on nd tap on Add device , select the device  a which you are adding and tap on discover device.

Note: Discovering the device must be done every time the device’s name is changed on the app.

ALEXA Commands
Now, you can control your smart device using voice commands on Alexa. Below are a few commands you can use:

• Alexa, turn on/off bedroom light.
• Alexa, set bedroom light to 50 percent.

THINGS TO REMEMBER BEFORE STARTING INSTALLATION:

1. V-TAC Smart Light App & Amazon Alexa App
2. Make sure you have Amazon Alexa Device(including Echo, Echo Tap, or Echo Dot)
3. Smart Device – Lamp
4. Stable Wifi network

GOOGLE HOME SETTINGS

Step1:

• a&b) Install the Google Home app via the App Store (iOS) or the Play Store (Android) and register. If you already have an existing account with Google Home, please proceed to logging in.
• Create a New Home/Choose from the existing home if any.
• Power ON the Google Home device and connect it to the App.(Then Proceed to step 2)

Step2: Once you are on the Google home page, tap on the Add “+” icon– to add a new device and skill. And then tap on Set up device as shown in below image.

Step3: Make sure the Smart Bulb is paired with V-TAC Smart Light app before starting step 3. Tap on the arrow section as highlighted in the below image.

Step4: Type “V-TAC Smart Light” on the search bar and tap on the icon of “V-TAC Smart Light”

Step5: Sign In with your V-TAC Smart Light Login credentials to Link the Smart Light device

Step6: Tap on Authorize in order to proceed to linking the device.

Step7

• Account will now be linked, please stay on the page you will be redirected in few seconds to select the device to add to your home.
• Select the device and tap on Next as show in image b.

Step8: Select the Home where you would like to add the Smart Light under. (Or) you can create a New home in order to add the Smart Light to it.

Step9: You have successfully added Smart Light device to your Google home App.

Step10:

• You can turn the Lamp On/OFF by taping on On/Off options as shown below. (OR) You can tap on the Smart Lamp.
• You will be redirected to page(as shown in image b) where you can control the lights “Power and Dimming functionality”.

Google Commands:
Now, you can control your smart device using voice commands on Google Home. Below are a few commands you can use:

• OK Google, turn on/off bedroot. m light
• OK Google, set bedroom light to 50 percent.

THINGS TO REMEMBER BEFORE STARTING INSTALLATION:

1. V-TAC Smart Light App & Google Home App
2. Make sure you have Google Home Device
3. Smart Device – Lamp
4. Stable Wifi network

IN CASE OF ANY QUERY/ISSUE WITH THE PRODUCT, PLEASE REACH OUT TO US AT: [email protected] FOR MORE PRODUCTS RANGE, INQUIRY PLEASE CONTACT OUR DISTRIBUTOR OR NEAREST
DEALERS. V-TAC EUROPE LTD. BULGARIA, PLOVDIV 4000, BUL.L.KARAVELOW 9B

References

• TAC.EU

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>