PDQ LH-LHR Passivebolt Powered Cylindrical Lock Installation Guide

October 30, 2023
PDQ

PDQ LH-LHR Passivebolt Powered Cylindrical Lock

GTS INSTALLATION INSTRUCTION

PASSIVEBOLT POWERED CYLINDRICAL LOCK

The PassiveBolt powered cylindrical lock is a secure and convenient way to lock your door. The lock comes with both mechanical and electrical components for installation. For any mechanical or electrical concerns, you can contact PassiveBolt customer support at Phone: 866-874-3662 or Email: support@passivebolt.com. You can also visit their website at www.pdqlocks.com or www.PassiveBolt.com for more information.

Product Usage Instructions

  1. CHECK HANDING OF LOCK to ensure it matches the door.
  2. PREPARE DOOR & INSTALL LATCH: Prepare the door according to the template provided. Install the latch with the radius towards the door frame. Secure with (2) #8 combo screws.
  3. INSTALL CHASSIS AND OUTSIDE TRIM: Install the chassis and outside trim using bolts.
  4. CAREFULLY REMOVE LOCK CONTROL MODULE (LCM): Remove the LCM from the cardboard.
  5. INSTALL READER ASSEMBLY: Install the reader assembly using flat head screws, reader wire, and the battery cover.
  6. INSTALL INSIDE ESCUTCHEON, BATTERIES, AND COVER: Install the inside escutcheon and batteries. Secure with a dog point set screw.
  7. HANDING INSTRUCTIONS: Rotate the inside rose plate and chassis to match the hand of the door using the wire chase slot on the other side. Install rose plate and secure with mounting screws.

LATCH DIRECTION

If your door is left-handed, use the left wire for the latch direction. If your door is right-handed, use the right wire for the latch direction.

INSTALLATION INSTRUCTION

PDQ-LH-LHR-Passivebolt-Powered-Cylindrical-
Lock-FIG-1

  1. CHECK HANDLING OF LOCK
    • If handing off the lock is not correct for opening, see the next page for handling instructions.
  2. PREPARE DOOR & INSTALL LATCH
    • prepare the door according to a template. Install latch, radius toward the door frame Secure with (2) #8 combo screws.
  3. INSTALL CHASSIS AND OUTSIDE TRIM
    • Install chassis assembly from the inside of the door.
    • Install outside trim assembly.
    • Secure with (2) flat head screws (thru bolts).
  4. CAREFULLY REMOVE THE LOCK CONTROL MODULE (LCM)
    • Disconnect the battery connector from LCM
    • Remove LCM by pulling the board off standoffs
    • Place the removed LCM on a piece of cardboard
  5. INSTALL READER ASSEMBLY
    • Install housing from outside of the door
    • Route wires through the door
    • Do not pinch wires
    • Secure with (2) flat head screws
    • Reinstall LCM on a backplate
  6. INSTALL INSIDE ESCUTCHEON, BATTERIES, AND COVER
    • Install inside escutcheon.
    • Secure with (2) pan head screws.
    • Install batteries and battery cover with flat head screw.
    • Install inside lever and secure with dog point set screw.

HANDING INSTRUCTIONS

AS REQUIRED, ROTATE INSIDE THE ROSE PLATE AND CHASSIS TO MATCH THE HAND OF THE DOOR.

TO ROTATE CHASSIS:

  1. Remove the rose plate mounting screws, then the rose plate.
  2. Unplug the motor connector. Feed motor connector and wire back through wire chase slot.
  3. Rotate chassis 1/2 turn (180°) maximum.
  4. Feed motor connector and wire forward through wire chase slot on the other side. Re-connect the motor connector.
  5. Rotate the rose plate to index with the chassis. (Arrows point to latch bolt edge of the door.)
  6. Install rose plate, secure with mounting screws.

Documents / Resources

| PDQ LH-LHR Passivebolt Powered Cylindrical Lock [pdf] Installation Guide
PB-9703 Rev0, LH-LHR, LH-LHR Passivebolt Powered Cylindrical Lock, Passivebolt Powered Cylindrical Lock, Powered Cylindrical Lock, Cylindrical Lock, Lock
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals