PDQ MRS BLE Only Mortise Lock Installation Guide
- October 30, 2023
- PDQ
Table of Contents
PDQ MRS BLE Only Mortise Lock
Product Information MRS BLE Only Mortise Lock
The MRS BLE Only Mortise Lock is a mechanical lock that can be installed on doors. The lock comes with a hardware kit (W51411), which includes a dead latch slider and a strike screw pack. The lock is available in two handings – LH/LHR and RH/RHR. The lock also includes Orlando/Memphis levers & ball knob.
Product Usage Instructions
- Check the handing of the lock body.
- Prepare the door by using the hardware kit, W51411, and installing the dead latch slider.
- Prepare the jamb by using the strike screw pack.
- Attach the lever by assembling the rose as shown and using the supplied hex key to tighten the socket head cap screw. For Orlando/Memphis levers & ball knob, skip this step and refer to step 6.
- Install the drive spindles/outside trim by retracting the latch and confirming the spindle engagement.
- Install the inside trim/rose by installing the spindle with the lever and securing it with machine screws supplied in the hardware kit, W51411. Confirm the spindle engagement and secure the rose plate by rotating clockwise until tight. For Orlando/Memphis levers & ball knob, tighten from underside with supplied hex key.
- Install the cylinder, turnpiece, and armor plate by installing the cylinder trim collar and turning it slightly recessed. Install the slotted set screw through the I/C bore to secure the housingfor I/C housings. Install screws supplied in the thumb turn screwpack.
- Install the inside mounting plate assembly and push extra wire into the door cavity. Secure it.
- Install the battery pack over two studs on the mounting plate and snap it onto retainers on the mounting plate. Plug in battery wire to control board.
- Install batteries and battery cover with (2) black pan head screws.
CHECK HANDING OF LOCK BODY
If handing of lock body is not correct for opening, consult factory for handing instruction.
DOOR PREPARATION
- Prepare the door for the mortise lock.
- Install the mortise case while feeding chassis wire into hole on inside of door.
- Gently pull wire through hole as chassis is inserted
- Secure using two (2) combo screws supplied in the hardware kit, W51411
JAMB PREPARATION
- Prepare the jamb for the mortise lock strike.
- Install Dead Latch Plate behind strike with slider toward bottom for dead latch.
- Install the strike and secure with two (2) combo screws supplied in the strike screw pack.
LEVER ATTACHMENT
- Assembly Outside Lever – If outside scalp was removed, install scalp. Assemble rose as shown using the supplied hex key to tighten the socket head cap screw.
- Orlando/Memphis Levers & Ball Knob – Skip the following step. Do not install inside lever and discard one (1) socket head cap screw. Refer to step 6.
- Assembly Inside Lever – Remove inside scalp. Assemble the inside rose as shown using the supplied hex key to tighten the socket head cap screw
INSTALLATION INSTRUCTIONS
Drive Spindles:
Install drive spindles and springs on both sides in orientation shown.
Outside Trim
- Install outside trim to door while aligning lever with drive spindle.
- Confirm spindle engagement in lock by rotating the lever down, retracting the latch.
INSTALL INSIDE TRIM / ROSE
- Install the inside rose assembly to the inside of the door. Align the spindle with the lever.
- Secure inside rose assembly with 1-1/2″ long flat head machine screws, supplied in the hardware kit, W51411 – Confirm the spindle engagement.
- Install the rose scalp by aligning the dimples with the slots in the rose plate. Secure by rotating clockwise until tight.
FOR ORLANDO/MEMPHIS LEVERS & BALL KNOB
Slide lever onto spindle. Install set screw in bottom of lever. Tighten from
underside with supplied hex key
CYLINDER, TURNPIECE AND ARMOR PLATE INSTALLATION
- Assembly cylinder, cylinder spring and cylinder trim collar.
- Thread the cylinder into the lock body until the cylinder is flush or slightly recessed in the cylinder trim collar.
- Secure the cylinder by tightening set screw through front of case, on the side of cylinder, with the hex key provided in the hardware kit, W51411.
- For I/C housings, install the slotted set screw through the I/C bore to secure the housing.
- Install the turnpiece and secure with two (2) truss head sheet metal screws, supplied in the thumb turn screw pack.
- Install the armor plate with two (2) flat head machine screws.
INSTALL INSIDE MOUNTING PLATE ASSEMBLY
- Install inside mounting plate assembly.
- Feed chassis wire through T slot in mounting plate.
- Secure with (4) pan head wood/metal screws.
- Make wire connection after reader is secure. Push extra wire into door cavity.
INSTALL BATTERY PACK
- Plug in battery wire to control board.
- Install battery pack over two studs on mounting plate.
- Snap battery pack onto retainers on mounting plate.
INSTALL BATTERIES AND BATTERY COVER
Install batteries and battery cover with (2) black pan head
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>