Equipment Hydraulic Scissor Lift User Manual

Equipment Hydraulic Scissor Lift

Mid-rise Scissor/Low Portable Lift

The Mid-rise Scissor/Low Portable Lift is a hydraulic lift that can lift up to 6614 lbs (3000 kg) with a maximum lifting height of 39 3/8 in (1000 mm). It has a lowered height of 4 9/64 in (105 mm) and a lifting time of 30 seconds. It requires a motor of 110 VAC at 60 Hz, 1 Ph, 2.95 hp (2.2 kW) and an air supply of 87 – 116 psi (6 – 8 bar). The single platform length is 55 1/8 in (1400 mm), the single platform width is 20 55/64 in (530 mm), and the width between platforms is 33 5/64 in (mm). The overall length (includes ramps) is 79 9/64 in (2010 mm), the overall width is 74 51/64 in (1900 mm), and the product weight is 1142 lbs (518 kg).

Usage Instructions

Attention
When using the Mid-rise Scissor/Low Portable Lift, ensure that the upper part of the cylinder does not rust and wear out the sealing ring. The user should raise the lift to the limit switch every week and repeat this process several times to lubricate the upper part of the cylinder.

Transport & Unpacking
When unpacking the lift, ensure that the packing material has been removed and check for any signs of damage to the machine. Keep the packing materials out of the reach of children as they can be a source of danger. Keep the packing for possible future transport.

Working Place
Choose a place to install the machine in compliance with current workplace safety regulations. The floor should not be broken or uneven so that the machine will be stable and the platform can move freely. If the installation is outside, it must be protected by some kind of roofing against rain. The machine must not be operated in explosive atmospheres. Maximum machine space requirements are 3200X2000mm with a minimum distance from walls as shown in the diagram.other than specially trained and authorized operators are expressly forbidden to enter this area.

Attention：
Congratulations on your purchase of this Hydraulic Scissor Lift. This model is the result of our vast experience in the production of fine-lifting vehicle machines. It represents the high degree of craftsmanship and reliability that have made us leader in these fields. It is a wheels-free hydraulic lift bridge with a lower profile, designed and built to meet the requirement of the operator changing tires in the tire shop and for minor mechanical jobs (oil change, changing brake pads etc.) as it reaches a lifting height of around one meter. This manual will give you an understanding of the operation, inspection, and basic maintenance of this lift. If you have any questions concerning the operation or maintenance of your lift, please consult the dealer. The design and manufacture of this lift fully comply with the lifting standards of CE. We have met these standards without reducing the performance or economy of operation of the lift. To maintain these high standards, it is important that you and your dealer pay close attention to the recommended maintenance schedules and operating instructions contained within this manual.

NOTES:
In the normal use of the machine, ensure the upper part of the cylinder does not rust, wear out the sealing ring, the user should be rise lift to the limit switch in every week, repeated several times to lubricate the upper partofthe cylinder。

Special specification

1. Equipment damage which in the process of shipment shall be claim by the
2. buyer to the carrier.
3. Design and manufacture have considered the safety performance. However, proper training and thorough operation can increase the safety. Not readingillustrates, shall not operate or repair the equipment.
4. Identify the motor and the current state requirement of the nameplate, byprofessional and qualified electrician to connect.
5. Products of the company to the part structure improvement without notice. On the previous sales product updates without any obligation to notifycustomer.
6. Not be more than the rated lifting weight.
7. Please carefully read the warning marks

IMPORTANT MANUAL INFORMATION

Particularly important information is distinguished inthis manual by the following notations:

NOTE:

• This manual should be considered a permanent part of this lift and shouldremain with it even if the lift is subsequently sold.
• We continually seek advancements in product design and quality. Therefore, while this manual contains the most current product information availableat the time of printing, there may be minor discrepancies between your lift andthismanual. If you have any questions concerning this manual, please consult yourdealer.

SAFETY INFORMATION

SCISSOR LIFT IS ONE KIND OF THE LIFTING EQUIPMENT. ITSSAFE USE AND OPERATION ARE DEPENDENT UPONTHEUSEOFPROPER OPERATION TECHNIQUES AS WELL AS THE EXPERTISEOFTHE OPERATOR. EVERY OPERATOR SHOULD KNOWTHE FOLLOWING REQUIREMENTS BEFORE OPERATION THIS LIFT. HE OR SHE SHOULD:

• OBTAIN THOROUGH INSTRUCTIONS FROM A COMPETENT SOURCEONALL ASPECTS OF LIFT OPERATION.
• OBSERVE THE WARNINGS AND MAINTENANCE REQUIREMENTSINTHE OWNER’S MANUAL.
• OBTAIN QUALIFIED TRAINING IN SAFE AND PROPER OPERATION TECHNIQUES.
• OBTAIN PROFESSIONAL TECHNICAL SERVICE AS INDICATEDIN MANUAL AND/OR WHEN MADE NECESSARY BY  MECHANICAL CONDITIONS.

Please read the following important labels carefully before operating this lift.

TRANSPORT & UNPACKING

Depending on the standard request, this lift and the hydraulic pump are protectedbytwo cartons with pallets. And the machine must be handled with a forklift withtheforks positioned as shown in the figure.

CAUTION
Once the packing material has been removed, checkthemachine for any sings of damage.

WARNING
Keep the packing materials out of the reach of childrenasthey can be a source of danger.
Keep the packing for possible future transport.

SPECIFICATIONS

WORKING PLACE

•  Choose the place the machine is to be installed in compliance with current work place safety regulations. The floor should not bebroken or uneven so that the machine will be stable andtheplatform can move freely.
• If the installation is out door, it must be protected by somekindofroofing against rain.
• The following work environment conditions are applicabl
  • Relative humidity: from 30-95% without condensation.
  • Temperature: 5-55℃.

WARNING
The machine must not be operated in explosive atmospheres.

Maximum machine space requirements are 3200X2000mm with minimum distance from walls as shown in the diagram.

WARNING
These measurements are also the machine working range. Persons other thanspecially trained and authorized operators are expressly forbidden to enter this area,

DESCRIPTION

NOTE
It is main parts figure above. More detailed components and assembly please seeexploded view

NOTE
It is main parts figure above. More detailed components and assembly please seeexploded view

INSTALLATION

Connecting pipes
There are two pipes from the hydraulic pump as shown in the figure. (X) is apneumatic pipe and used for the safety lock. (Y) is a hydraulic oil pipe andusedfor the hydraulic cylinders Enter hydraulic oil
Remove the motor box off, and then turn the oil cap anti-clockwise to opentheoil inlet. Fill in the hydraulic oil 30# from the oil inlet as shown in the figure.

NOTE

• Make sure that there is sufficient oil in the tank when the machine working
• Do not overfill the oil tank, otherwise it may overflow when the oil warms upandexpands.
• Make sure that the oil tank cap is properly closed before working

OPERATION

During all operations, keep hands and other parts of the body as far as possiblefrommoving parts of the machine. Necklace, bracelets and too large clothes, canbe dangerous for the operator.

WARNING
When the lift is working (lifting a car), remember:
Any personnel do not get in the lift and the car, it could result in severe injury or death!

OPERATION
During all operations, keep hands and other parts of the body as far as possible from moving parts of the machine. Necklaces, bracelets and too-large clothes canbe dangerous for the operator.

WARNING

STORING

If the machine as to be stored for a long time you have to :

• Go down the platforms and no heavy object on them.
• Disconnect the machine from all power sources.
• Grease all the parts that could be damaged if they dry out.
• Empty hydraulic oil reservoir and wrap the machine in a sheet of protectiveplastic to prevent dust from reaching the internal working parts. If the machine as to working again after a long storing period, it is necessary to:
• Put the oil into the reservoir again. 8.6 Restore the electric connection.

ELECTRIC SYSTEM

HYDRAULIC SYSTEM

Structure principle diagram

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>