inventor PFI2VO-09 Air Conditioning Systems Remote Controller User Manual

June 6, 2024
inventor

inventor PFI2VO-09 Air Conditioning Systems Remote Controller User Manual

inventor PFI2VO-09 Air Conditioning Systems Remote Controller User
Manual

Remote Controller Specifications

inventor PFI2VO-09 Air Conditioning Systems Remote Controller - Remote
Controller Specifications

Quick Start Guide

inventor PFI2VO-09 Air Conditioning Systems Remote Controller - Quick Start
Guide

NOT SURE WHAT A FUNCTION DOES?

Refer to the How to Use Basic Functions and How to Use Advanced Functions sections of this manual for a detailed description of how to use your air conditioner.

SPECIAL NOTE

  • Button designs on your unit may differ slightly from the example shown.
  • If the indoor unit does not have a particular function, pressing that function’s button on the remote control will have no effect.
  • When there are wide differentces between “Remote controller Manual” and “USER’S MANUAL” on function description, the description of “USER’S MANUAL” shall prevail.

Handling the Remote Controller

Inserting and Replacing Batteries

Your air conditioning unit may come with two batteries(some units). Put the batteries in the remote control before use.

  1. Slide the back cover from the remote control downward, exposing the battery compartment.
  2. Insert the batteries, paying attention to match up the (+) and (-) ends of the batteries with the symbols inside the battery compartment.
  3. Slide the battery cover back into place.

inventor PFI2VO-09 Air Conditioning Systems Remote Controller - Inserting
and Replacing Batteries

BATTERY NOTES

For optimum product performance:

  • Do not mix old and new batteries, or batteries of different types.
  • Do not leave batteries in the remote control if you don’t plan on using the device for more than 2 months.

BATTERY DISPOSAL

Do not dispose of batteries as unsorted municipal waste. Refer to local laws for properdisposal of batteries.

TIPS FOR USING REMOTE CONTROL

  • The remote control must be used within 8 meters of the unit.
  • The unit will beep when remote signal is received.
  • Curtains, other materials and direct sunlight can interfere with the infrared signal receiver.
  • Remove batteries if the remote will not be used more than 2 months.

NOTES FOR USING REMOTE CONTROL

The device could comply with the local national regulations.

  • In Canada, it should comply with CAN ICES-3(B)/NMB-3(B).
  • In USA, this device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.
  • Changes or modifications not approved by the party responsible for compliance could void user’s authority to operate the equipment.

Buttons and Functions

Before you begin using your new air conditioner, make sure to familiarize yourself with its remote control. The following is a brief introduction to the remote control itself. For instructions on how to operate your air conditioner, refer to the How to Use Basic Functions section of this manual.

inventor PFI2VO-09 Air Conditioning Systems Remote Controller - Buttons and
Functions

Remote Screen Indicators

Information are displayed when the remote controller is power up.

inventor PFI2VO-09 Air Conditioning Systems Remote Controller - Remote
Screen Indicators

Note:

All indicators shown in the figure are for the purpose of clear presentation. But during the actual operation, only the relative function signs are shown on the display window.

How to Use Basic Functions

Before operation, please ensure the unit is plugged in and power is available.

AUTO Mode

inventor PFI2VO-09 Air Conditioning Systems Remote Controller - AUTO
Mode

NOTE:

  1. In AUTO mode, the unit will automatically select the COOL, FAN, or HEAT function based on the set temperature.
  2. In AUTO mode, fan speed can not be set.

COOL or HEAT Mode

inventor PFI2VO-09 Air Conditioning Systems Remote Controller - COOL or HEAT
Mode

DRY Mode

inventor PFI2VO-09 Air Conditioning Systems Remote Controller - DRY
Mode

NOTE : In DRY mode, fan speed can not be set since it has already been automatically controlled.

FAN Mode

inventor PFI2VO-09 Air Conditioning Systems Remote Controller - FAN
Mode

NOTE : In FAN mode, you can’t set the temperature. As a result , no temperature displays in remote screen.

Setting the TIMER

TIMER ON/OFF – Set the amount of time after which the unit will automatically turn on/off.

TIMER ON setting

inventor PFI2VO-09 Air Conditioning Systems Remote Controller - TIMER ON
setting

TIMER OFF setting

inventor PFI2VO-09 Air Conditioning Systems Remote Controller - TIMER OFF
setting

NOTE:

  1. When setting the TIMER ON or TIMER OFF, the time will increase by 30 minutes increments with each press, up to 10 hours. After 10 hours and up to 24, it will increase in 1 hour increments. (For example, press 5 times to get 2.5h, and press 10 times to get 5h,) The timer will revert to 0.0 after 24.
  2. Cancel either function by setting its timer to 0.0h.

TIMER ON & OFF setting (example)

Keep in mind that the time periods you set for both functions refer to hours after the current time.

inventor PFI2VO-09 Air Conditioning Systems Remote Controller - TIMER ON &
OFF setting \(example\)

How to Use Advanced Functions

Swing function

inventor PFI2VO-09 Air Conditioning Systems Remote Controller - Swing
function LED DISPLAY

Press this button to turn on and turn off the display on the indoor unit.

Silence function

Keep pressing Fan button for more than 2 seconds to activate/disable Silence function.
Due to low frequency operation of compressor, it may result in insufficient cooling and heating capacity. Pressing ON/OFF, Mode, Sleep, Turbo or Clean button while operating will cancel silence function.

8°C function

Press this button 2 times during one second under HEAT Mode and setting temperature of 16 C/60 F or 20 C/68 F.

inventor PFI2VO-09 Air Conditioning Systems Remote Controller - 8°C
function

Pressing On/Off, Sleep, Mode, Fan and Temp. button while operating will cancel this function.

LOCK function

inventor PFI2VO-09 Air Conditioning Systems Remote Controller - LOCK
function

SET function

inventor PFI2VO-09 Air Conditioning Systems Remote Controller - SET
function

  • Press the SET button to enter the function setting, then press SET button or TEMP or TEMP button to select the desired function. The selected symbol will flash on the display area, press the OK button to confirm.
  • To cancel the selected function, just perform the same procedures as above.
  • Press the SET button to scroll through operation functions as follows: Sleep( ) Follow Me( ) AP mode( )

Sleep function ( ) :

The SLEEP function is used to decrease energy use while you sleep (and don t need the same temperature settings to stay comfortable). This function can only be activated via remote control.

For the detail, see sleep operation in USER S MANUAL.

Note : The SLEEP function is not available in FAN or DRY mode.

FRESH ( ):

When the FRESH function is initiated, the ion generator is energized and will help to purify the air in the room.

Follow me function( ):

The FOLLOW ME function enables the remote control to measure the temperature at its current location and send this signal to the air conditioner every 3 minutes interval. When using AUTO, COOL or HEAT modes, measuring ambient temperature from the remote control(instead of from the indoor unit itself) will enable the air conditioner to optimize the temperature around you and ensure maximum comfort.

NOTE : Press and hold Turbo button for seven seconds to start/stop memory feature of Follow Me function.

  • If the memory feature is activated, On displays for 3 seconds on the screen.
  • If the memory feature is stopped, OF displays for 3 seconds on the screen.
  • While the memory feature is activated, press the ON/OFF button, shift the mode or power failure will not cancel the Follow me function.

AP function( ) :

Choose AP mode to do wireless network configuration. For some units, it doesn’t work by pressing the SET button. To enter the AP mode, continuously press the LED button seven times in 10 seconds.

All the pictures in the manual are for explanatory purposes only. The actual shape of the unit you purchased may be slightly different, but the operations and functions are the same. The company may not be held responsible for any misprinted information. The design and the specifications of the product for reasons, such as product improvement, are subject to change without any prior notice.

Please consult with the manufacturer at +30 211 300 3300 or with the Sales agency for further details. Any future updates to the manual will be uploaded to the service website, and it is advised to always check for the latest version.

Scan here to download the latest version of this manual.
www.inventorairconditioner.com/media- library

inventor logo

AIR CONDITIONING SYSTEMS
REMOTE CONTROLLER

V:1.0 202106

Manufacturer: INVENTOR A.G. S.A.
24th km National Road Athens – Lamia & 2 Thoukididou Str., Ag.Stefanos, 14565
Tel.: +30 211 300 3300, Fax: +30 211 300 3333 – www.inventor.ac

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals