SB-LPLRC200S LAT Pulldown, Low Row Combo Machine Owner’s Manual

Parts Diagram Exploded View

PARTS LIST AND PART NUMBERS

1
S1l| W702S| COUN$ERWEIGH$ 3HEE$| ____| 14l
S2| W7027| COUN$ERWEIGH$ 3UPPOR$ PIPE| $1S HOLE 3PACING 127.| 4
SS| | 17S2 HIGH AND LOW PULL BACK CU3HION.| Ф8*11S| 1

INSTALLATION DETAILS

STEP 1:
INSTALL THE WEIGHT STACK FRAME ASSEMBLY(1) TO THE UNDER FRAME ASSEMBLY(4). INSTALL RUBBER FOOT PADS(24) NOW (OPTIONAL).

STEP 2:

1. INSTALL GUIDERODS(7) INTO HOLES LOCATED INSIDE BOTTOM OF WEIGHT STACK FRAME.
2. SLIDE #32 SPACERS ON FROM TOP OF GUIDE RODS TO HAVE 2 ON EACH GUIDE ROD AT THE BOTTOM.
3. INSTALL WEIGHT PLATES(29). SMALLEST WEIGHT PLATE IS LAST AS THIS IS THE TOP PLATE.
4. INSTALL #27 ON TO GUIDE ROD AND INTO TOP PLATE.
5. INSTALL SELECTOR ROD(28) INTO WEIGHT STACK CENTER HOLE.
6. SECURE TOP OF GUIDE RODS TO WEIGHT STACK FRAME USING #9 PLATE AND #17 BOLTS.
7. PLACE SELECTOR PIN(30) INTO WEIGHT STACK.

REFER TO PAGE 10 FOR FURTHER ASSISTANCE

STEP 3:
INSTALL THE SUPPORT UPRIGHT ASSEMBLY TO THE UNDER FRAME ASSEMBLY(4).

STEP 4:
INSTALL THE UPPER CONNECTING CROSS BEAM TO THE WEIGHT STACK FRAME AND THE SUPPORT UPRIGHT ASSEMBLY

STEP 5:

1. INSERT THE CABLE END OF THE LONG CABLE FROM THE BOTTOM SIDE OF THE UPPER CONNECTING CROSS BEAM AND FOLLOW DIAGRAM TO THE TOP PLATE SELECTOR ROD, THEN INSERT AND TIGHTEN SET SCREWS AFTERSTEP 2.
2. INSTALL SHORT CABLE AS SHOWN IN DIAGRAM BY GOING UNDER LARGER LOW-ROW PULLEY AND OVER SMALLER PULLEY. ATTACH PULLEYS AS YOU INSTALL THE CABLE.
   

STEP 6:
INSTALL THE ADJUSTABLE LEG PAD SUPPORT(5) TO THE SUPPORT UPRIGHT ASSEMBLY. INSERT DROP PIN INTO SELECTOR HOLES FIRST TO HELP LINE UP #5, #10, #19, AND

21 (PIVOT POINT). THEN ATTACH THE LOW ROW PLATFORM FOOT SUPPORT(6) TO THE

BASE OF THE SUPPORT UPRIGHT ASSEMBLY, THEN INSERT #11 BOLT THROUGH ALL HOLES TO SECURE PLATFORM TO THE BASE SUPPORT.

STEP 7:
INSTALL THE SEAT PAD(33), LAT PULLDOWN BAR, AND FRONT AND REAR WEIGHT PLATE GUARDS(25 & 26)

APPENDIX 1: ORIENTATION DISTINGUISHING METHOD OF COUNTERWEIGHT SHEET
APPENDIX 1: INSTALLATION SEQUENCE OF COUNTERWEIGHT

1. NSERT THE FIRST COUNTERWEIGHT PIECE FROM TOP TO BOTTOM.
   

2. EACH OF THE NEXT STEPS IS THE SAME AS THE FIRST

3. THE NUMBER OF INSTRUMENTS WITH SINGLE PIECE WEIGHT OF 10LB AND COUNTERWEIGHT OF 200LB IS 19 + 1(HEAD PIECE)
   

4. AFTER INSTALLING THE HEAD PIECE PUT ON THE PLASTIC FIXING PLATE.

5. FIRST MOVE THE PLASTIC FIXING PLATE TO THE POSITION SHOWN IN THE FIGURE. AND THEN TIGHTEN IT WITH SCREWS TO COMPLETE THE WHOLE INSTALLATION PROCESS OF COUNTERWEIGHT PIECE.
   

**INSTALL WEIGHT STACK CABLE

**

PRODUCT DESCRIPTION, SPECS, & FEATURES

SB FITNESS EQUIPMENT / SB-LPLRC200S

PRODUCT NAME: LAT PULLDOVJN/LOW ROW COMBO MACHINE
WEIGHT STACK: 200LB
PRODUCT FEATURES: LAT PULLDOWN AND LOW ROW
PRODUCT DIMENSIONS: 86″H X 48″W X101.5″ L
MUSCLES WORKED: LATISSIMUS DORSI, TRAPEZIOD, BICEPS, REAR DELTS

FOR YOUR SAFETY

1. CONSULT YOUR PHYSICIAN OR HEALTH CARE PROVIDER BEFORE USING YOUR MACHINE AND/OR EXERCISE EQUIPMENT.
2. IF YOU HAVE A PHYSICAL DISABILITY OR AN ATHLETIC DISABILITY, IT IS REQUIRED THAT YOU CONSULT YOUR PHYSICIAN OR HEALTH CARE PROVIDER BEFORE PROCEEDING WITH ANY EXERCISE PROGRAM.
3. BEFORE USING THIS PRODUCT, PLEASE READ THIS MANUAL CAREFULLY. SB FITNESS EQUIPMENT IS NOT RESPONSIBLE FOR ANY PERSONAL INJURY OR DAMAGE CAUSED BY USING THIS PRODUCT UNDER ANY CIRCUMSTANCES OR NEGLIGENCE CAUSED BY THE USER.

ASSEMBLY INSTRUCTION AND PRODEDURES

1. THE PURPOSE OF THIS SECTION OF THE USER MANUAL IS TO ENSURE THAT THE MACHINE CAN BE INSTALLED EASILY AND CORRECTLY. PLEASE FOLLOW INSTRUCTIONS CAREFULLY AND ENTIRELY.
2. BECAUSE OF ITS LARGE SIZE AND WEIGHT, THE MACHINE SHOULD BE ASSEMBLED NEAR THE LOCATION WHERE IT WILL BE USED.
3. PLACE ALL PARTS OF THE MACHINE IN THE ASSEMBLY AREA AND REMOVE ALL PACKING MATERIAL. DO NOT DISCARD THE PACKAGING MATERIAL UNTIL THE ASSEMBLY IS COMPLETE.
4. ALL BOLTS MUST BE TIGHTENED DURING ASSEMBLY UNLESS OTHERWISE SPECIFIED, AND ALL BOLTS MUST BE TIGHTENED AFTER ASSEMBLY, IN ORDER FOR ASSEMBLY TO BE COMPLETE.
5. WHEN ASSEMBLING THE SB-LPLRC200S, MAKE SURE THAT ALL PARTS ARE ASSEMBLED ACCORDING TO THE ASSEMBLY DIAGRAM.

WARRNTY INFORMATION

WHAT IS COVERED SB
SB FITNESS WARRANTS TO THE ORIGINAL PURCHASER OF THIS MACHINE THAT THE FRA ME OF THE PRODUCT SHALL BE FREE FROM DEFECT IN MATERIALS AND WORK MANSHIP AND UNDER WARRANTY FOR A PERIOD OF TWO YEARS FROM THE DATE OF PURCHASE. ALL OTHER PARTS AND COMPONENTS OF THE PRODUCT SHALL BE FREE FROM DEFECT IN MATERIAL AND WORKMANSHIP AND UNDER WARRANTY FOR A PERIOD OF ONE YEAR FROM THE DATE OF PURCHASE WHEN THE PRODUCT IS USED AS RECOMMENDED BY SB FITNESS UNDER NORMAL USES AND CONDITIONS. DURING THE WARRANTY PERIOD SB FITNESS WILL AT NO ADDITIONAL CHARGE TO YOU, REPAIR OR REPLACE (AT SB FITNESS’ OPTION) THE FRAME OR ANY PART OF THE PRODUCT IF IT BECOMES DEFECTIVE, MALFUNCTIONS, OR OTHERWISE FAILS TO CONFORM WITH THIS LIMITED WARRANTY. ALL LABOR SHALL BE THE RESPONSIBILITY OF THE OWNER.

WHAT IS NOT COVERED
THIS LIMITED WARRANTY APPLIES ONLY FOR PRODUCT SOLD IN THE UNITED STATES UNDER THE SB FITNESS BRAND NAME. THIS WARRANTY DOES NOT COVER NORMAL WEAR AND TEAR ON ITEMS SUCH AS. BUT NOT LIMITED TO, TRANSPORTATION WHEELS, FOOT PEDALS, RUBBER GRIPS. PLASTIC END CAPS. SCRATCHED PARTS, BROKEN COVERS,COSMETIC DAMAGE,AND EXCLUDES PAINT & FINISH. WEAR ITEMS PERTAIN TO CO MPONENTS THAT MIGHT NEED TO BE REPLACED DUE TO WEAR AND TEAR RESULTING FROM NORMAL USAGE.THIS WARRANTY IS VOID IF THE PRODUCT IS IMPROPERLY STORED, ASSEMBLED. ALTERED AND/OR MODI-FIED IN ANY WAY. MISUSED. ABUSED, IS SUBJECT TO ACCIDENT, IS IMPROPERLY MAINTAINED, AND THIS WARRANTY DOES NOT COVER REPAIR FOR ANY NOISES SUCH AS: SQUEAKS. CLUNKS, THU MPS RESULTING FRO M POOR OR LACK OF PREVENTIVE MAINTENANCE. THIS LIMITED WARRANTY DOES EXTENT TO ANY PRODUCT THAT IS DAMAGED OR RENDERED DEFECTIVE;(A) AS A RESULT OF ACCIDENT,MISUSE. OR ABUSE:(B) USE WITH THE PRODUCT OF ANY PART NOT MANUFACTURED OR SOLD BY SB FITNESS; (C) BY MODIFICATION OF THE PRODUCT; (D) BY NOR MAL WEAR AND TEAR: (E) OPERATION USING INCORRECT PO WER SUPPLIES; OR (F) AS A RESULT OF SERVICE BY ANYONE OTHER THAN SB FITNESS. OR AN AUTHORIZED SB FITNESS SERVICE PROVIDER.

ASSMPTION OF RISK

WARNING
THIS PRODUCT HAS BEEN MANUFACTURED WITH SAFETY IN MIND. WARRANTY APPLIES ONLY WHEN USED AS INSTRUCTED. FAILURE TO COMPLY WITH THE WARNINGS AND PRECAUTIONS DESCRIBED IN THIS DOCUMENT MAY CAUSE PERSONAL INJURY AND RESULT IN WARRANTY BEING VOIDED. PLEASE NOTE THAT SB FITNESS ASSUMES NO RESPONSIBILITY FOR ANY ACCIDENTS RESULTING FROM USE.

CALIFORNIA PROPOSITION 65 WARNING
WARINING:
THIS PRODUCT CAN EXPOSE YOU TO CHEMICALS INCLUDING ARSENIC, WHICH IS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER. FOR MORE INFORMATION. GO TO WWW.P65WARNINGS .CA.GOV.XN–IVG

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>