EHEIM Typ 2214 Classic Flter Leading Aquarium Instruction Manual

: June 9, 2024
: EHEIM

EHEIM - Symbols 1

250

(Typ 2214)

Operating Instructions

I

EHEIM Typ 2214 Classic Flter Leading Aquarium - a1

II

EHEIM Typ 2214 Classic Flter Leading Aquarium - b4

III

USA

Aquarium exterior filters classicVARIO+e (type 2214)

IMPORTANT SAFETY INSTRUCTIONS

FOR HOUSEHOLD USE ONLY
WARNING! RISK OF ELECTRIC SHOCK! This pump has not been investigated for use in swimming pools areas!
DO NOT RUN DRY!

WARNING – To guard against injury, basic safety precautions should be observed, including the following.

a) READ AND FOLLOW ALL SAFETY INSTRUCTIONS.

b ) DANGER – To avoid possible electric shock, special care should be taken since water is employed in the use of aquarium equipment. For each of the following situations, do not attempt repairs by yourself; return the appliance to an authorized service facility for service or discard the appliance.
1) If the appliance falls into the water, DON’T reach for it! First unplug it and then retrieve it. If electrical components of the appliance get wet, unplug the appliance immediately.
2) If the appliance shows any sign of abnormal water leakage, immediately unplug it from the power source.
3) Carefully examine the appliance after installation. It should not be plugged in if there is water on parts not intended to be wet.
4) Do not operate any appliance if it has a damaged cord or plug, or if it is malfunctioning or has been dropped or damaged in any manner.
5) To avoid the possibility of the appliance plug or receptacle getting wet, position aquarium stand and tank to one side of a wall-mounted receptacle to prevent water from dripping onto the receptacle or plug.

A ”drip loop”, shown in the figure, should be arranged by the user for each cord connecting an aquarium appliance to a receptacle. The ”drip loop” is that part of the cord below the level of the receptacle, or the connector if an extension cord is used, to prevent water traveling along the cord and coming in contact with the receptacle.
If the plug or socket does get wet, DON’T unplug the cord. Disconnect the fuse or circuit breaker that supplies power to the appliance. Then unplug and examine for presence of water in the receptacle.

POWER SUPPLY CORD
AQUARIUM TANK
DRIP LOOP
AC/DC ADAPTER

c) Close supervision is necessary when any appliance is used by or near children.

d) To avoid injury, do not contact moving parts or hot parts such as heaters, reflectors, lamp bulbs, and the like.

e) Always unplug an appliance from an outlet when not in use, before putting on or taking off parts, and before cleaning. Never yank cord to pull plug from outlet. Grasp the plug and pull to disconnect.

f ) Do not use an appliance for other than intended use. The use of attachments not recommended or sold by the appliance manufacturer may cause an unsafe condition.

g) Do not install or store the appliance where it will be exposed to the weather or to temperatures below freezing.

h) Make sure an appliance mounted on a tank is securely installed before operating it.

i) Read and observe all the important notices on the appliance.

j) If an extension cord is necessary, a cord with a proper rating should be used. A cord rated for less amperes or watts than the appliance rating may overheat. Care should be taken to arrange the cord so that it will not be tripped over or pulled.

l) “SAVE THESE INSTRUCTIONS”.

FCC WARNING STATEMENT (USA only)

FCC CAUTION
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Translation of the original operating manual Aquarium exterior filters classicVARIO+e

1. General user instructions

EHEIM - Symbols 1

Information on using the operating manual

Before using the appliance for the first time, the operating manual must be read fully and understood. Consider the operating manual as part of the product and keep in a safe and accessible location. Enclose this operating manual if passing the appliance on to a third party.

Symbol explanation

The following symbols are used on the appliance:

The appliance must only be used indoors, and exclusively for aquariums.

The appliance is of protection class III.

IP X4 The symbol advises that the device is protected against splashed water.

The appliance is certified according to the relevant national regulations and directives, and conforms to EU standards.

The following symbols and signal words are used in this operating manual:

DANGER!
The symbol indicates imminent danger from electric shock that can result in death or serious injury.

DANGER!
The symbol indicates imminent danger that can result in death or serious injury.

WARNING!
The he symbol indicates imminent danger that can result in moderate to minor injury or a health risk.

CAUTION!
The symbol indicates the danger of material damage.

Note with useful information and tips.

Typographical conventions:

A Reference to a figure; in this case, reference to figure A.

You are prompted for an action.

2. Application

The appliance and all parts included in the scope of delivery are intended for private use and must only be used:

For the cleaning of aquarium water in fresh and salt water aquariums.
indoors
in compliance with the technical data.

The following limitations apply to the appliance:

do not use for commercial or industrial purposes.
the water temperature may not exceed 35°C.
Corrosive, highly flammable, aggressive or explosive substances, foodstuffs and drinking water must not be conveyed.
never operate without a water flow.

3. Safety instructions

Risks for persons and property can arise from this appliance if the appliance is improperly used or not used as intended or if the safety instructions are not heeded.

For your safety

Do not let the appliance packaging and small parts get into the hands of children or people who are unaware of how to handle them, as hazards can arise (danger of suffocation!). Keep away from animals.
Only for EU countries: This appliance can be used by children from the age of 3 and by persons with reduced physical, sensory or mental capabilities or lack of experience and/or knowledge if they are supervised and have been instructed in the safe use of the appliance and have understood the resulting dangers. Children must not play with the appliance. Cleaning and user maintenance must not be carried out by children unless they are supervised.
This equipment is not intended for use by persons (including children) with limited physical, sensory or mental abilities or for persons with no experience or knowledge unless they are supervised by a person respond for safety or unless they have received from such a person instructions on how to use the equipment. Children should be supervised to ensure that they do not play with the equipment.
Before use, carry out a visual inspection to ensure that the appliance, especially the mains cable and plug, are undamaged.
Do not use the device if it does not function properly or if it is damaged.
Never use the appliance with a damaged mains cable or power supply unit.
The power cable of this device can not be replaced. When the line is damaged, the device must no longer be used.
Repairs must only be carried out by an EHEIM service centre.
Do not carry the appliance by the mains cable, and to disconnect from the mains, always pull on the plug and not on the cable or appliance.
Protect the mains cable against heat, oil and sharp edges.
Only carry out the work described in these instructions.
Never make technical modifications to the appliance.
Only use original spare parts and accessories for the appliance.
The device should be protected by means of a residual current protective device with a maximum rated residual current of 30 mA. Ask your electrician.
If they are not being used, always disconnect all devices in the aquarium from the power supply before you install/remove any parts and before all cleaning and maintenance work.
Protect the mains socket and mains plug against moisture. It is recommended to form a drip loop with the mains cable to prevent any water running along the cable to the mains socket.
The electrical data of the power supply must match the data of the power mains. This data is found on the type plate of power supply, the packaging and in these instructions.
This appliance working without the earth connection.
Only use the power supply unit supplied with the filter. If a replacement is required the original EHEIM power supply unit must be used.

POWER SUPPLY CORD
AQUARIUM TANK
DRIP LOOP
AC/DC ADAPTER

4. Delivery scope and component overview (see I)

(1) Pump head (2) Filter container (3) Hose connection pressure side (4) Hose connection suction side (5) Filter insert (6) 5x Filter mat (blue) (7) Filter fleece (white) (8) Carbon fleece (9) Suction pipe (10) Suction basket (11) 4x suction cups with clamping bracket (12) Discharge bend (13) Nozzle pipe (14) Plug (15) 2x Double tap with quick-release coupling (16) Screw sleeve (17) Hose (18) Power supply unit (19) Mains cable (20) Status- LED (21) Sealing ring (22) 4x clamping bracket (23) Locking part (24) Pump cover (25) Pump wheel with axle

5. Preparation (See II and III)

1 Check that all parts are present.

II. 1. Connect the intake strainer to the intake pipe.
2. Cut a piece of hose (min. 1.5 cm) from the enclosed hose and use it to connect the outlet bend to the nozzle pipe.
3. Close the end of the nozzle pipe with the plug.
4. Connect the clamp and the suction cup and clip them (2x each) onto the suction and nozzle pipes.
5. Cut 2 more pieces of hose each approx. 5- 10 cm from the hose and connect one piece of hose each to a double tap. To secure the hose connection, screw the union nut over the hose.
6. Connect the power supply unit to the mains cable.

III. 1. Open all 4 clamps and remove the pump head from the filter canister.
2. take out the filter insert by the handle and open the cover by turning it to the left.
3. Take out all the filter mats and rinse them gently under running water.
4. Place the filter media back into the filter insert as shown in Figure 4.1 : (a) 5 blue foam mats, (b) white cotton wool fleece, (c) black carbon fleece as the top layer, and close the lid.

Figure 4.2 (optional): (a) EHEIM MECH, EHEIM MECHpro or EHEIM bioMECH, (b) 1 foam mat blue, (c) EHEIM SUBSTRAT or EHEIM SUBSTRATpro (d) fine filter pad, (e) carbon fleece black as top layer.

The carbon fleece is used to adsorb possible dissolved pollutants in the water when setting up a new aquarium. aquarium. After a running-in period of approx. 2 – 4 weeks, charcoal fleece should be removed.

5. Put the pump head back on the filter container.

Make sure that the sealing ring is correctly positioned in its guide and is not damaged or dirty.

6. Lock all 4 clamping brackets.

6. Installation

A Place the filter under the aquarium – at least the pump head must be at least 10 cm below the aquarium water level.

When choosing a location for the unit, pay attention to the installation height. In order to achieve optimum functional reliability, there must be a maximum of 180 cm between the water surface and the bottom of the filter.
Always operate the filter in an upright position.

B Mount the nozzle tube by pressing it firmly against a side window.

C Place the nozzle pipe so that it is approx. 1 cm below the water surface and the nozzles are aligned parallel to the surface.

D Fix the suction pipe in the rear corner of the same side window with the suction cups.

E Connect the double tap (1) to the hose connection (suction side) on the filter container and the double tap (2) to the hose connection on the pump head.

F 1. Connect the double tap on the suction side (on the filter tank) to the suction pipe and the double tap on the pressure side (on the pump head) to the nozzle pipe.
2. Secure all hose connections with the union nuts.

Keep hose lengths as short as possible to prevent loops and kinks and minimise flow resistance.

7. Start up

G 1. Disconnect the connection between the outlet bend and the nozzle pipe on the pressure side.
2. Suction at the end of the outlet bend until the filter system automatically fills with water.
3. Once the water circuit has been established, reconnect the outlet bend to the nozzle pipe.
4. Plug the cable of the power supply unit into the pump head.

8. Operation

System requirements
Wifi-enabled end devices (smart phone, tablet, notebook etc.).

Creating a network
1. Insert the power cable of the power supply unit in the mains socket. The status LED (20) lights up.

Status LED flashes white: Network is being searched for or created.
The status LED illuminates blue: A new network has been created (master mode).

Connecting to the Wifi network
2. Open the network settings of your terminal device (smartphone, tablet, notebook etc.).
3. Connect the terminal device to the Wifi network (SSID) EHEIM classicVARIO XXXXXXXX.
4. Enter the network security key.

The network security key is found on the device.
Alternatively, you can also scan the QR code 1 (see label) to establish the connection.

Calling up the website
5. Open your web browser and enter the following address: http://192.168.1.1

Alternatively, you can also scan the QR code 2 (see label) to open the software in the browser.

Initial configuration
6. Select the desired language from the language selection and follow the instructions for the initial configuration.

Meaning of the status LED filter

The status LED flashes white: The network is being searched for or created
The status LED illuminates blue: The device is in master mode
The status LED illuminates green: The device is connected to another EHEIM digital device

Reset
Touch the touch field below the status LED (20) for approx. 8 – 10 seconds until the status LED lights up in a colour change.

If the status LED lights up green, the reset is complete and the device is created.
Network security key (Key) and QR code 1 are invalid. Connection to the network is possible without the network security key.

9. Cleaning

1. Unplug the mains plug of the power supply unit from the socket.

H 2. Close all shut-off levers of the double taps.
3. Separate both double taps by turning the screw sleeves to the left.

III. 4. Open all 4 clamping brackets and remove the pump head from the filter container.
5. Take out the filter insert by the handle and open the lid by turning it to the left.
6. Remove all filter mats and rinse them gently under running water.
7. Place the filter media back into the filter insert as shown in Figure 4.1 or 4.2 and close the lid.
8. Put the pump head back on the filter container.

Make sure that the sealing ring is correctly positioned in its guide and is not damaged or dirty.

9. Close all 4 clamping brackets.
10. Connect the double taps by turning the screw sleeves clockwise.
11. Restore the water circuit. When the filter system is completely filled with water, put the appliance into operation by plugging in the mains plug.

10. Maintenance

I 1. Pull out the mains plug and remove the pump head as described in chapter 9. cleaning point 1 – 4.
2. Open the locking part and remove the pump cover.
3. Carefully remove the pump wheel from the pump chamber.
4. Clean all parts under running water with a brush.

Caution Risk of breakage: The axle of the pump wheel is made of ceramic.

5. It is best to clean the pump chamber with the 4009560 cleaning brush.
6. Assemble all pump parts in reverse order.

11. Decommissioning

Disposal

When disposing of the appliance, heed the respective statutory regulations. Information on the disposal of electrical and electronic appliances in the European Union: Within the European Union, disposal of electrically operated appliances is governed by national regulations that are based on the EU Directive 2012/19/EU on waste electrical and electronic equipment (WEEE). The appliance may no longer be disposed of with the municipal or household waste. The appliance will be accepted free of charge at municipal collection points or recycling centres. The product packaging is made up of recyclable materials. Dispose of them in an environmentally responsible manner and take them for recycling.

12. Technical data

See page 128

EHEIM Typ 2214 Classic Flter Leading Aquarium - e3

Type| classicVario
2214
---|---
For aquariums up to| 50 – 250 l
11 – 55 Imp. gal.
13 – 66 US gal.
Pump output| 510 l/h
112 Imp. gal./h
135 US gal./h
Delivery head wat. col.| 1,80 m
5’11”
Power consumption| 1,7 – 9,8 W
Canister volume| 3,0 l
0,7 Imp. gal.
0,8 US gal.
Dimensions (Ø x h)| 170 x 355 mm
6.7 x 14 in.
Wireless data transmission| WiFi 2.4GHz – IEEE802.11 b/g/n
Security keys| WPA, WPA2, WPA/WPA2
Transmitting power| ≤ 20 dBm
Frequency bands|

Channel 1 – 11 / 2412 MHz – 2462 MHz

Hereby, EHEIM GmbH & Co. KG, declares that the radio equipment type EHEIM classicVario+e is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.eheim.com

Reproduction or copying – even parts thereof – only with the express permission of the producer.

EHEIM logo2