VALBERG CH 60 2M W 302C Cooker Hood User Manual

Cooker Hood
978336 – CH 60 2M W 302C
978337 – CH 60 2M K 302C
978338 – CH 60 2M X 302C

CH 60 2M W 302C Cooker Hood

Thanks!
Thank you for choosing this VAL BERG product.
Chosen, tested and recommended by ELECTOR DEPOT, the products of the VAL BERG brand are easy to use, reliable and of an impeccable standard.
Thanks to this appliance, you can be sure that each use will bring you satisfaction.
Welcome to ELECTOR DEPOT.
Visit our website: www.electrodepot.fr

Using the appliance

Installation
If you have an outlet to the outside, your cooker hood can be connected as below picture by means of an extraction duct (enamel, aluminum, flexible pipe or nonflammable  aterial with an interior diameter of 120mm).

1. Before installation, turn the unit off and unplug it from the outlet.
2. The cooker hoods should be placed at a distance of 65-75cm from the cooking surface for  best effect. See Pic 1.
3. To install onto the wall, drill 4 holes of Ø 8mm on a suitable place according with the centre distance of hole in the back of the cooker hood. See Pic 2
4. Insert the nut into the holes.
5. Insert the screws into the nuts and tight.
6. Put up the cooker hood onto the fixed screws.
7. Then use the attached accessories enclosed to turn the screws into the two holes of inside the hood, and then fix the screws to tighten the hood onto the wall.
8. Put the one way valve onto the cooker hood.

Method B See Pic3:

1. Drill 4 holes of Ø 6mm at the bottom of the hanging cupboard.
2. Put the one way valve on the air outlet of cooker hood, then install the cooker hood on the bottom of the cupboard, tighten the cooker hood with enclosed 4 screws.
3. Install the adjusted board on the bottom of the hood in order to keep out the gap between
   hood back and cupboard.

Notice: There are 2 methods for ventilation, including ‘ horizontal ventilation’ and ‘vertical ventilation’. Pay attention to the ventilation method when installing.
Horizontal ventilation: See Pic 4A, please use the cover to seal the outlet on the top, then the air can be vented from back.
Vertical ventilation: See Pic 4B, please use the cover to seal the outlet on the back, then the air can be vented from top. Installing without external opening

Recycling version
Contact your supplier to obtain active carbon filters to transform the extractor hood into a recycling hood.
Installing the active carbon filter (cassette)

• Check that the diameter of the active carbon filter corresponds the outlet diameter.
• If necessary, remove the per-installed diameter adapter.
• Position the active carbon filter on the outlet and attach it in place by turning anticlockwise.

Installing the active carbon filter (cut-out)

• The metal filter has to be removed before the active carbon filter is installed.
• To open the metal filter, press on the locking device and pull the filter downwards.
• Place the precept filter on top of the  metal filter. Hold in position using the metal rods (supplied according to the model).
• Replace the metal filter in its original position.

NOTE
Make sure that the filter is properly attached; otherwise it could become dislodged and cause a hazard. The installation of a carbon filter reduces the extraction power of the hood.
Air ventilation setting
Outdoor air ventilation: Turn the adjuster to outdoor position(pic.5A), install the outlet, turn on the cooker hood, then the air will be vented from the outside outlet.
Indoor air ventilation: Turn the adjuster to indoor position (pic.5B), install the outlet cover, turn on the cooker hood, then the air can be vented from the inside outlet.

WARNING
For safety reason, use only the same size of fixing or mounting screws which are recommended in this instruction manual.
Failure to install the screws or fixing device in accordance with these instructions may result in electrical hazards.
Start using your cooker hood
Push button
a. Press the button “Stop”, the motor is stopped then.
b. Press the button “Low”, the motor is running at low speed.
c. Press the button “Mid”, the motor is running at medium speed.
d. Press the button “High”, the motor is running at high speed.
e. Press the button “Light”, both lights start shining .Press the button again; the lights are switched off then.

Useful information

Troubleshooting

position.
Fan switch failed| Contact service center.
Motor failed| Contact service center.
Light does not work, motor does not work| House fuses blown| Reset/Replace fuses.
Mains power cable s loose or disconnected| Refit mains power cable to power outlet.
Switch power outlet on.
Oil leakage| One way valve and the outlet are not tightly sealed| Take down the one way valve and seal with sealant.
Leakage from the connection of chimney and cover| Take chimney down and seal.
Lights not working| Broken or faulty bulbs| Replace bulbs as per this instruction.
Insufficient suction| The distance between the cooker hood and the gas top is too far| Refit the cooker hood to the correct distance.
The Cooker hood inclines| The fixing screw is not tight enough| Tighten the hanging screw and make it horizontal.

NOTE
Any electrical repairs to this appliance must conform to your local, state and federal laws. Please contact the service center if in any doubt before undertaking any of the above. Always disconnect the unit from the power source when opening the unit.
Cleaning and maintenance
CAUTION
Before maintenance or cleaning is carried out, the cooker hood should be disconnected from the mains power supply.
Ensure that the cooker hood is switched off at the wall socket and the plug removed.
External surfaces are susceptible to scratches and abrasions, so follow the cleaning instructions to ensure the best possible result is achieved without damage.
General
Cleaning and maintenance should be carried out with the appliance cold especially when cleaning. Avoid leaving alkaline or acid substances (lemon juice, vinegar etc.) on the surfaces.
Stainless steel
The stainless steel must be cleaned regularly (e.G.Weekly) to ensure a long life expectancy. Dry with a clean soft cloth. A specialized stainless steel cleaning fluid may be used.
NOTE
Ensure that wiping is done along with the grain of the stainless steel to prevent any unsightly crisscross scratching patterns from appearing.
Control panel surface
The inlay control panel can be cleaned using warm soapy  water. Ensure the cloth is clean and well wrung before cleaning. Use a dry soft cloth to remove any excess moisture
left after cleaning.
IMPORTANT
Using neutral detergents and avoid using harsh cleaning chemicals, strong household detergents or products containing abrasives,as this will affect the appearance of the appliance and potentially remove any printing of artwork on the control panel and will void manufactures warranted. Grease mesh filters
The mesh filters can be cleaned by hand. Soak them for about 3 minute in water with a mild detergent and then brush it gently with a soft brush. Do not apply too much pressure so as to avoid any damage to it . (Leave to dry naturally out of direct sunlight.)

Filters should be washed separately to crockery and kitchen utensils. It is advisable not to use rinse aid.

• Removing the filters as the instruction.
• Please do not use abrasive detergent for it will damage the hood.

Installing grease mesh filters
To install filters for the following four steps.

• Angle the filter into the slots at the back of the hood.
• Push the button on the handle of the filter.
• Release the handle once the filter fits into a resting position.
• Repeat to install all filters.

Carbon filter-not supplied
Activated carbon filter can be used to trap odors. Normally the activated carbon filter should be changed every 3 to 6 months according to your cooking habit. The installation procedure of activated carbon filter is as below.

1. Before installing or replacing the carbon filters, please remove power to the unit.
2. Press the filter lock and remove the mesh filter.
3. Turn the carbon filter on both side of the motor anticlockwise. Replace the carbon filters with the new carbon filters.
4. Place the mesh filter
5. Connect the power supply to the wall socket.

NOTE
Make sure the filter is securely locked. Otherwise, it would loosen and cause danger.
When activated carbon filter attached, the suction power will be lowered.
Changing the light
Light source in this product can only be replaced by qualified  professionals.
Please contact after-sales service if the light source fails.
The light source shall be removed at the end of the product’s useful life, with sorting and recycling done separately.

• Use the screw driver loosen the ST4*8MM self tapping  screw (2pcs) from the lighting panel, take out the lighting fixture. Open the terminal box that connected with the
  wire, disconnect the wire connector and replace the lamp.

• ILCOS D code for this lamp is: DBS-2/65-H-120/33
  – LED modules –rectangle lamp
  – Max wattage: 1×2 W
  – Voltage range: AC 110-240V
  – Dimensions:

Information for dismantling
Do not dismantle the appliance in a way which is not shown  in the user manual. The appliance could not be dismantled by  user. At the end of life, the appliance should not be disposed of with household waste. Check with your Local Authority or retainer for recycling advice.

WARRANTY CONDITION

This product has a 2-year warranty as of the date of purchase, covering any fault resulting from a manufacturing or material defect. This warranty does not cover defects or damage resulting from incorrect installation, improper use or abnormal wear of the appliance.
upon presentation of the sales receipt.

MADE IN PRC
ELECTRO DEPOT
1 route de Vendeville
59155 FACHES-THUMESNIL
FRANCE

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>