PROLED IP20 Flex Strip 300 Mono Light User Manual

PROLED IP20 Flex Strip 300 Mono Light

PROLED FLEX STRIP

Product Description

The PROLED FLEX STRIP is a flexible LED lighting strip available in three different models: IP20, IP53, and IP68. It is manufactured by MBN GmbH and is designed to be used in various lighting applications. PROLED FLEX STRIP allows to make different types of illuminiation. It can be used for main illumination, for background illuminiation, ambiente illumination etc. as well as inside or outside or even under water.

Safety Instructions

Before using the PROLED FLEX STRIP, please read the following safety instructions carefully:

• Do not bend the strip horizontally or vertically.
• Avoid using the product in aggressive environments that contain chemicals such as sulfur, chlorine, bromine, etc. and organic materials containing N, P, S, etc., and heavy metals such as Sn, PB, Hg, Sb, Bi, As, etc.
• Please don’t install this Flex Strip during thunderstorms, intense magnetic or high-voltage electrical fields. Take care about correct connections to minimize the risk of damage of components or short circuits.
• Always be sure to mount this unit in an area with proper ventilation to avoid overheating.
• Check if the power supply fulfills the voltage and power requirements of the Flex Strip as well as the polarity.
• Make all connections only in powerless condition and make sure that no short circuit is existing before switching on the Flex Strip. Please contact your local dealer for updates.

Installation Instructions

Follow these steps to install the PROLED FLEX STRIP:

1. Ensure that the surface where the strip will be attached is clean and dry.
2. Peel off the protective film from the adhesive tape on the back of the strip.
3. Stick the strip onto the surface and press firmly to ensure it is securely attached.
4. If required, cut the strip at the designated cut points. Make sure to remove the protective film from the adhesive tape before attaching it to a new surface.
5. Connect the strip to a compatible 12-24 VDC power supply.

Installation place

1. Do not install the Flex Strip in an overheated ambient, for example near a radiator, or in a bad cooling surrounding.
2. If the installation is in a high humidity surrounding, please use, suitable for the application, Flex Strip IP53 or IP68.
3. Do not use the Flex Strip in an aggressive surrounding, for example containing sulfur, chlorid, brom etc.
4. a. Gas vapour can diffuse through the silicon cover and react with the LED surface. Due to this, the light output will be significant lower and a temperature shift can’t be avoided. Further more the resistance will rise, which result in higher current.
5. b. Organic materials, which contains N, P, S. Heavy metals like Sn, PB, Hg, Sb, Bi, As etc.

Installation

• Check the correct function of the Flex Strip, but in unrolled shape, before fixing it. Complains after installation can not be accepted.
• Switch off the mains supply and secure it against switching on.
• Please check if the correct units will be installed, this means that the power supply must have same voltage like the connected Flex Strip.
• Please check if the power supply has enough power, for example to compensate power loss due to long cables and if the correct cables are used to minimize voltage loss. It is suggested that the power supply has ca. 20% more power than the connected load.
• When connecting the cables, please take care about the polarity.
• Adhesive surface must be non-conductive. It is recommended to stick the Flex Strips into anodized aluminium profiles.
• Flex Strip can only be bend sharply at areas with no electronical components. The minimum bending radius is 2 cm. Flex Strip is not allowed to be twisted.
• Installation must be made on a heat disposal underground, which is adequate dimensioned, to remove the heat of the desired Flex Strip. The underground must be free of greas, oil, silicone, dust and dirt. We suggest Isopropanol for cleaning.
• Installation on uneven, low heat-conductive grounding is not suggested as the life time will be shorted and make fixing difficult. These include wood, plaster board, wallpaper etc.
• Avoid fixing over profile splice. Because of thermal expanding or shrinking a damage of Flex Strip can happen. Divide the Flex Strip in this case and use flexible connections, for example wire strap

Installation steps:

1. Remove the protection foil of the adhesive tape
2. Place the Flex Strip in the profile and stuck it gently. Do not use any sharp or metallic tools
3. Cut away the not needed part of the Flex Strip, with a scissor, at the marked cutting line.
4. Please pay attention, that an already sticked Flex Strip should not be removed again. It is possible that electronical parts or soldering points will break, which isn’t covered by guarantee or warrenty.
5. Rest pieces can be used at other project. Only connection cable must be soldered to the Flex Strip.

Error Troubleshooting

If you encounter any issues with the PROLED FLEX STRIP, refer to the following troubleshooting guide:

• If the LEDs are damaged due to paint or any other external factors, contact your supplier for assistance.
• If there is a shadow on the wall caused by improper cable installation, adjust the cable accordingly.

Preface

Thanks for choosing the PROLED FLEX STRIP. Before installation and use, we strongly recommend you to read this manual carefully. If the Flex Strip has been damaged during transport, please report this to your supplier immediately. Please don’t take any action without contacting your supplier first.

Limited Warranty

In case of quality problems we provide free repair or replacement from the day of purchase, if this product has been used properly in accordance with the user’s manual, except in following cases:

1. Any defects caused by wrong operation.
2. Any damages caused by unauthorized removal, maintenance, modifying, incorrect connection and replacement of chips.
3. Any damages due to transportation, vibration etc. after purchase.
4. Any damages caused by earthquake, fire, lightning, pollution and abnormal voltage.
5. Any damages caused by negligence, inappropriate storing at high temperatures and humidity or near harmful chemicals.
6. Product has been updated

Cautions
Please follow below information using Flex Strips.

• Do not bend sharply
• Do not cover during working
• Do not bend horizontaly
• Do not connect to mains supply
• Do not expose to pressure

Safety cautions

• Installation only according to local specifications
• Installation only by professional staff
• Use only Class 2 power supplies
• Power supply must have correct voltage. Voltage must correspond to voltage listed on Flex Strip
• Use only cables which are specified for more than 80°C
• Use correct dimension of cables. Wrong cables can lead to overheat and eventually result in fire. Cable must be approved for the existing voltage and current
• Use the Flex Strip only at an ambient temperature of -10 – 45°C
• Do not stick IP20 & IP53 Flex Strips on conductive surfaces

Connection diagram

Following diagrams show the connection of Flex Strips. Please refer to the manual of your controller/dimmer for exact connection diagram.

Connection of monochromatic Flex Strips without dimmer

Connection of monochromatic Flex Strips with dimmer

Connection of RGB Flex Strips with Dimmer

Soldering of cables at IP53 Flex Strips

If you have to solder a connection to a Flex Strip IP53, please work according to following steps

1. Cut the Flex Strip on marked cutting line.
2. Remove silicone from the soldering pads and Solder the cable correctly. Please take care about correct polarity.
3. Cover the soldering point with acid free silicone for example PROLED sealing glue L6396.
4. Cut a small piece of heat shrink tube.
5. Cover the soldering point with heat shrink tube
6. Take care that the security foil of the adhesive tape can be removed

Soldering of cables at IP68 Flex Strips
If you have to solder a connection to a Flex Strip IP68, please work according to following steps. Please be advised, that correctly sealed end caps have only a IP65 classification.

1. Cut the Flex Strip on marked cutting line
2. Remove the silicone from the soldering pads. Solder the cable correctly . Please take care about correct polarity.
3. Cut a hole for power cable into the end cap.
4. Move the end cap over the cable.
5. Pierce the tube outlet with the cap of the sealing glue, for example PROLED L6396.
6. Screw the outlet funnel on the tube
7. Cut the funnel diagonally.
8. Fill the end cap completely with the glue
9. Move the end cap over the strip, so that the soldering pads are covered.

Caution:
Please leave new glued end cap minimum 24 h without movement for drying. Please be advised, that silicone is not a maintenance-free. The glue must be checked regularly, but at least once a year, and must be replaced if needed.

Fixing of IP68 Flex Strips
For fixing of Flex Strip IP68 is possible with corresponding plastic clips. If they can’t be used, the IP68 Flex Strip must be secured with a suitable glue. The existing 3M-tape is only applicable as installation help, but not for long term fixing. Following please see examples, how they can be attached

ATTENTION: When installing IP53 or IP68 Flex Strips outdoors, thermal expansion and contraction must be considered. The adhesion must not go continuously over the entire length, as this prevents corresponding movements and can lead to the damaging of the Flex Strip. Depending on the temperature differences, the expansion or shrinkage can be up to 1.5 cm/m. This must be taken into account during installation

Trouble shooting

Following you will see some failures and their results

ATTENTION:
Installation and commissioning may only be performed by qualified persons. National installation regulations must be observed. Luminaires must be disconnected from mains before any work. This product is considered a “containing product” within the meaning of Regulation (EU) 2019/2020 and (EU) 2019/2015. The light source is an integral part of the containing product. A separation of the light source and the containing product leads to irreversible damage. Replacing the light source using commonly available tools does not make sense for this product. The used light source can be removed for testing purposes. The replacement of the light source is not intended, as this will destroy the containing product.

MBN GmbH, Balthasar-Schaller-Str. 3, 86316 Friedberg – Germany www.proled.com

References

• PROLED: proled.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>