milleteknik 350-091 PoE Switch 4p FLX M+ PoE Switch with Battery Backup User Manual
- June 11, 2024
- Milleteknik
Table of Contents
- ABOUT POE FROM MILLETEKNIK
- HOW POE POWERS DEVICES CONNECTED TO THE POWER SUPPLY
- COMPONENT OVERVIEW POE FLX M
- MOUNTING ON A WALL OR IN A 19 “RACK
- CONNECTION OF BATTERIES
- MOTHERBOARD – DESCRIPTION
- SHORT DESCRIPTION FOR POE SWITCH 4P
- COMMISSIONING – HOW TO START THE UNIT
- STATUS INDICATIONS
- MAINTENANCE
- PRODUCT DATA SHEET
- LIMITATIONS
- PRODUCT LIFE CYCLE, ENVIRONMENTAL IMPACT AND RECYCLING
- ADDRESS AND CONTACT DETAILS
- Documents / Resources
350-091 PoE Switch 4p FLX
M+ PoE Switch with Battery Backup
User Manual
ABOUT POE FROM MILLETEKNIK
The series is designed to power PoE devices such as access systems,
surveillance cameras and other equipment that can be operated with Power over
Ethernet. Through its function as a battery backup, the PoE device can
continue to be powered in the event of a power failure.
PoE switch 4p M, PoE switch 4p FLX S+ and PoE switch 4p FLX M+ are for
security systems whereas, reliable power supply with battery backup and PoE
function is needed. Our PoE have something we call “controlled charging”,
which is a safety function that means that batteries are not charged with more
than 0.5 A. By controlling the charging of batteries, the lifespan of
batteries is significantly extended.
The PoE Switch 4p Expansion kit is for expanding the number of PoE ports in
PoE switch 4p FLX S+ and PoE switch 4p FLX M+.
HOW POE POWERS DEVICES CONNECTED TO THE POWER SUPPLY
PoE can power, for example, surveillance cameras.
Connect external devices to be powered via PoE in PoE ports.
Connect other devices that do not need to be power supplied in LAN ports.
COMPONENT OVERVIEW POE FLX M
Symbol | Explanation |
---|---|
A | Brackets, reversible. |
B | Casing in powder-coated sheet metal. |
C | Power supply, (placed under the motherboard). |
D | Motherboard. |
E | Three places for PoE switches. One PoE switch is installed from the |
factory.
Four PoE ports are on the left and two LAN ports are on the right.
F| Room for batteries.
G| Cable entries.
MOUNTING ON A WALL OR IN A 19 “RACK
The unit can be mounted in a 19 ”rack or on a wall. The included brackets can be attached in two ways: When mounting on a wall, the brackets must sit backwards, against the wall. When mounting in a 19 ”rack, the console must be at the front edge of the unit.
Figure 1. FLX M – mount brackets
Left bracket facing the front for mounting in a 19 “rack.
Right bracket facing the back for wall mounting.
IMPORTANT
Leave 100 mm free around the air vents.
4.1. Console for FLX M and FLX L
Bracket is reversible and can be mounted in two ways. It comes with brackets
in to the device.
Two consoles must be used for FLX M.
CONNECTION OF BATTERIES
Battery wiring is mounted on the circuit board upon delivery. Pictures below only show how to connect wiring.
- Place the batteries in the cabinet with the battery terminals facing outwards, against the cabinet door.
- Connect the battery cable. Red cable on plus and black cable on minus.
If possible, disconnect mains voltage when replacing the battery.
Figure 2. Wiring diagram for batteries in battery backup
Connect the terminals correctly so that you do not damage the equipment.
MOTHERBOARD – DESCRIPTION
See technical data for more information.
The motherboard controls the device and distributes power. See technical data
for more information.
Table 2. Circuit board overview, explanation
No | On the circuit board | Explanation |
---|---|---|
1 | J24 | Connection for control of power supply. |
2 | D6 | LED 1. |
3 | J11 | connection external LED. |
4 | D11 | LED 2. |
5 | JU2 | Control of alarm threshold. |
6 | JU3 | Connection to external alarm. |
7 | J6 | Connection to buzzer. |
8 | P2:3-5 | Connection to sum alarm. |
9 | P2:1-2 | Load output |
10 | P1:1-3 | Connection to the mains. |
6.1. Connect the mains to the motherboard (PCB)
6.1.1. Connect mains
Pull wiring through the cable entry on the cabinet.
If possible, secure the mains cable with cable ties where possible.
Electrical network cabling shall be kept separate from other cabling to avoid
EMC interference.
Figure 4. Connect the mains to the motherboard
Connect the mains cable to the terminal before it is put back on the
motherboard. Secure F and N with cable ties for electrical safety.
Table 3. Electrical network connections
Letter | Explanation |
---|---|
F | Phase |
N | Neutral |
PE | Protective earth |
ELECTRICAL MAINS CONNECTION 230 V AC ON CIRCUIT BOARD
Check that the marking on the circuit board matches the cable arrangement on
the terminal block.
6.2. Connect load
MAX CURRENT
Maximum current must not be exceeded. Maximum current is indicated on the
CEmarking on the unit.
Table 4. Load connections
Circuit board number | Explanation |
---|---|
P2: 1 | Connection for load 1 + |
P2: 2 | Connection for load 1 – |
6.3. Control alarm limit
Alarm for low battery voltage in battery operation can be controlled.
By jumpering JU2, the limit for when the unit should give an alarm can be
lowered.
Alarms are given when the battery voltage in battery drops below the limit.
Table 5. Alarm limits
Alarm limit at low battery voltage | 12 V | 24 V |
---|---|---|
JU2 with jumper* | 10.2 V | 24.0 V |
JU2 without jumper * | 13.2 V | 26.5 V |
Alarm limit at low battery voltage | 12 V | 24 V |
--- | --- | --- |
*The unit is delivered with jumper on JU2
SHORT DESCRIPTION FOR POE SWITCH 4P
No | Terminal no | Explanation |
---|---|---|
1 | J5 | 2 pcs RJ-45 ports for data, not PoE, (powered). |
2 | J5 | 4 pcs RJ-45 powered ports for connecting PoE devices. |
3 | J2 | Power supply 48 V. |
4 | J8 | Connection for data transmission when additional PoE switch 4p card is |
connected.
A| –| Indication, yellow LED lights when data is being transferred.
B| –| Indication, green LED lights up when device is plugged in. This is only
an indication that the port is connected and not the connected device’s
status.
Figure 5. PoE switch with extra card
Two cards are connected with cable on 4, or a patch cable between 1 on each
card.
The picture shows how cards sit on top of each other in the PoE switch 4p FLX
S+. In the PoE switch 4p FLX M+, the cards are connected separately in
mounting plate.
How the software is accessed in the PoE Switch
This section shows how to log in to the switch’s configuration web page.
In order to configure the software in the switch, access to the switch
requires the correct IP address to be set on the computer.
Access to the switch’s software is through a browser (Chrome, Edge, Firefox).
Follow the steps to access the switch’s settings.
NOTE
The settings shown are settings for PC (Windows 7 – Windows 11).
NOTICE
The address of the PoE switch is: 192.168.1.1 and username and password are:
admin/admin
- Open settings and go to Network and Internet -> Advanced network settings. Open more network card options.
- A Network Connections window will appear showing all available network connections on the computer. Double-click the network connection you use to connect to the switch.
- Ethernet status window appears. click the button Characteristics as shown in the figure below.
- Double-click Internet Protocol Version 4 (TCP / IPv4).
- Set the computer’s IP address and subnet mask as shown in the figure below. By default, the product’s IP address be 192.168.2.1. You can set any IP address as long as it is not the same as your switch’s IP address and is in the same network segment as your switch’s IP address. Press OK to apply the TCP/IPv4 settings you just made. Now you can connect to your switch using a web browser (Chrome, Edge or Firefox).
- Connect an RJ-45 cable and connect to the PoE switch.
- Start the browser on your computer.
- Write 192.168.2.1 (or the IP address of the switch, if you have changed it) in the browser’s URL field and press Enter.
- Log in to the switch with username and password. the default username and password for the configuration web page is: admin/admin.
- From the switch’s web page, its status can be seen and the switch can also be configured here.
The switch has built-in documentation, (in English), for the various parts that can be configured.
COMMISSIONING – HOW TO START THE UNIT
The unit works normally when the indicator LED on the outside of the cabinet
door lights up with a solid green light. See front panel for other status
indications.
It may take up to 72 hours before the batteries are fully charged.
STATUS INDICATIONS
Solid green light: normal operation.
Solid yellow glow: Low battery voltage.
Solid red light: Low battery when the load output fuse is blown.
MAINTENANCE
The system with the exception of batteries is maintenance-free when installed in an indoor environment.
battery change
- If possible, disconnect mains (voltage) when replacing the battery.
- Disconnect battery cables. Note how battery cables are mounted before removing them.
- Remove battery fuse between batteries.
- Insert and fasten the new batteries.
- Connect the battery cables in the same way as before.
- Connect battery fuse between batteries.
- Switch on mains voltage. The indicator LED may not be green (up to 72 hours), until the batteries are charged.
- Test the system by briefly disconnecting the mains voltage, (= the load is driven by the batteries), and then switch on the mains voltage again.
PRODUCT DATA SHEET
PoE product data sheet / technical data
Figure 6. PoE Switch 4p FLX M+
Name | Article number | E-number (SV) |
---|---|---|
PoE Switch 4p/8p FLX M+ | FM01C10048P05004PU | 5171953 |
More information
https://www.milleteknik.se/produkt/batteribackup-poe-4p-flx-m/
12.1.2. About PoE from Milleteknik
The series is designed to power PoE devices such as access systems,
surveillance cameras and other equipment that can be operated with Power over
Ethernet. Through its function as a battery backup, the PoE device can
continue to be powered in the event of a power failure.
PoE switch 4p M, PoE switch 4p FLX S+ and PoE switch 4p FLX M+ are for
security systems where a, reliable power supply with battery backup and PoE
function is needed. Our PoE have something we call “controlled charging”,
which is a safety function that means that batteries are not charged with more
than 0.5 A. By controlling the charging of batteries, the lifespan of
batteries is significantly extended.
The PoE Switch 4p Expansion kit is for expanding the number of PoE ports in
PoE switch 4p FLX S+ and PoE switch 4p FLX M+.
POE SWITCH 4P FLX M+
12.1.3. Power over Ethernet from Milleteknik
- PoE for security applications with the need for power supply with backup power.
- Proven, reliable technology.
- For fixed installation.
- Swedish made.
12.1.4. Limitations
IMPORTANT
Note that 802.3at type2 is not supported, as the PoE card lacks a handshake
function for type 2. Read more. [16] The product is tested and verified
against Axim access systems and Din box access systems and is therefore
recommended for use only with these systems. The product is currently not
recommended for other products that have an af/at handshake procedure. The
product deviates from standard IEEE 802.3af per port and IEEE 802.3at as the
power is modified to be used together with Axim passer system and Din box
passer system, which leads to shortcomings, (PoE-connected product does not
start), against products that require handshake.
12.1.5. Areas of use
- Power supply for camera surveillance and other applications that can be powered by PoE.
- Security applications powered by PoE that need backup power in the event of a power outage.
12.1.6. Alarm
The device alarms for:
Low battery voltage, low battery voltage in the event of a broken fuse on the
load output.
12.1.7. Fixed installation
The product is intended for fixed installation. The battery backup must be
installed by a qualified installer.
12.1.8. Battery types
The ECO series can be used with AGM batteries. Do not mix types of batteries,
brand or used and new batteries.
12.2. Regulations and certifications
12.2.1. Requirements that the product meets
EMC: | EMC Directive 2014 / 30EU |
---|---|
Electricity: | Low voltage directive: 2014/35 / EU EN 60950-1 |
PoE: | IEEE 802.3af, IEEE 802.3at/30.8 W Note that 802.3at type2 is not |
supported, as the PoE card lacks a handshake function for type 2.
CE:| CE directive according to: 765/2008
Emission:| EN61000-6-: 2001 EN55022: 1998: -A1: 2000, A2: 2003 Klass B,
EN61000-3-2: 2001
BS EN/EN55032 (CISPR32) Class B, BS EN/EN61000-3-2,-3, EAC TP TC 020,
CNS13438, GB9254 Class B, GB17625.1
12.3. Expected operating time in the event of a power failure ( with new batteries)
PoE| Bat- tery| Power 15.4 W| Power 30.8 W|
Power 62 W| [sv] Effect 90 W| Power 100 W| Power
120 W| Power 180W| Power 240 W
---|---|---|---|---|---|---|---|---|---
PoE switch 4p/8p FLX M+ (48 V)| 4 pcs 14 Ah| 35 h| 17 h 30 min.| 8 h 15 min.|
[sv]| 4 h 45 min.| 3 h 50 min.| 2 h 20 min.| 1 h 40 min.
12.4. Circuit boards – Technical data
12.4.1. Technical data: CEO 3
Table 6. CEO3 V 2.5
Info | Explanation |
---|---|
Article title | CEO3 |
Product description | CEO 3 is the next generation circuit board for simpler |
battery backups. Advanced functions that were not previously possible in
simpler battery backups are now available as standard. CEO 3 is a reliable
heart in simpler battery backups with fewer components than before, which
reduces the environmental impact.
Measure| 120 x 55 mm x 52 mm
Own consumption| 32 mA
Fuse on output| F1: T2.5A, mains fuse.
F6: T5A, load fuse +, P2:1.
F7: T16A, battery fuse.
Outputs| One cargo outlet, fused.
Insurance| Load output: + secured.
Alarm via| Triggered load securing, potential-free shifting. Conclusion CO /
NO. PRO1: Via alarm terminal J13 (NC- CO). PRO2: Via alarm terminal J13 (NC-
CO). PRO2 v3: Via J11 and J12 to motherboard on to the parent system. PRO 3:
Via J11 and J12 to motherboard on to the parent system.
Protection against:| Deep discharge, short circuit, overload and overvoltage.
Table 7. Indications
Indicator diode | Green | Orange | RED |
---|---|---|---|
(2) / D2 | OK | Low battery voltage / fuse fault. | Low battery voltage with |
broken fuse on output.
(4) / D11| –| Overvoltage.| Batteries incorrectly connected.
Table 8. Alarm limits
Alarm limit at low battery voltage | 48 V |
---|---|
(5) / JU2 with jumper | 50.5 V |
(5) / JU 2 without jumper | 48 V |
The unit is delivered without a jumper on (8) / JU2
Table 9. sum alarm
sum alarm
(8) P2: 3| NO
(8) P2: 4| CO
(8) P2: 5| NC
12.4.2. Technical data: PoE card
LIMITATIONS
IMPORTANT
Note that 802.3at type2 is not supported, as the PoE card lacks a handshake
function for type 2. Read more. [16] The product is tested and verified
against Axim access systems and Din box access systems and is therefore
recommended for use only with these systems. The product is currently not
recommended for other products that have an aft/at handshake procedure. The
product deviates from standard IEEE 802.3af per port and IEEE 802.3at as the
power is modified to be used together with Axim passer system and Din box
passer system, which leads to shortcomings, (PoE-connected product does not
start), against products that require handshake.
Prod- uct| Nub- beer of PoE / LAN ports| Max power per
port| PoE budget| Ether- net type| Net- work ports|
Interface| Funs – tins| Type, insect- tor and
switch
---|---|---|---|---|---|---|---|---
PoE Switch 4p FLX M+| 4/2| 30,8 @ 54,6 V DC| 320 W| Fast Ethernet Mbit PoE
switch| 10 / 100 PoE| 1000Base-T RJ-45| Autonoe guttation, Atop- link (auto
MDI/MDI-X)| Unman aged. There is no software interface to control the switch.
12.5. Power supply
12.5.1. Power supply – Technical Data RSP-320-48
Info | Explanation |
---|---|
Output voltage | 54.6 V |
Output current | 0 A – 6.7 A |
Output voltage, ripple | 240 mVp-p |
Overvoltage | 58.4 V – 68 V |
Voltage recharge, ripple / current limitation | Less than 1.2 Vp-p |
Efficiency | 90% |
Current limitation | 105% – 135% |
Constant voltage | +/- 0.5% |
Regulatory accuracy | +/- 1.0% |
Input current | 2 A |
Mains voltage frequency | 47 Hz- 63 Hz |
Mains voltage | 124 V AC – 370 V AC |
Brand effect | 321.6 W |
Temperature range | -30°C – +70°C |
Info | Explanation |
--- | --- |
Humidity range | 20% – 90% RH non-condensed |
The power supply is adapted and calibrated with the battery / hardware of the battery backup. Only power and calibrated power supplies may be used. Contact support when changing power supplies. Use of power supplies coming from another source may cause damage not covered by the warranty. Warranty is canceled if power supplies (from a source other than support / designated by support) that are not correctly calibrated are used.
12.6. Technical data enclosures
12.6.1. Enclosures – Technical Data FLX M
Info | Explanation |
---|---|
Name | FLX M |
Enclosure class | IP 32 |
Measure | Height: 224 mm, width 438 mm, depth 212 mm |
Height units | 5 HE |
Mounting | Wall or 19 “rack |
Ambient temperature | + 5 ° C – + 40 ° C. For best battery life: + 15 ° C to + |
25 ° C.
Environment| Environmental class 1, indoors. 20% ~ 90% relative humidity
Material| Powder coated sheet
Color| Black
Cable entries, number| 4
Batteries that fit| 4 pcs 12 V, 14 Ah.
12.7. Link to the latest information
Products and software are subject to updates, you will always find the latest
information on our website.
PoE series
12.8. Warranty, support, country of manufacture and country of origin
12.8.1. Warranty
The product has a two-year warranty, from the date of purchase (unless
otherwise agreed). Support during the warranty period can be reached at
support@milleteknik.se or telephone, +46
31-34 00 230. Compensation for travel and / or working hours in connection
with locating faults, installing repaired or replaced goods is not included in
the warranty. Contact Milleteknik for more information. Milleteknik provides
support during the product’s lifetime, however, no later than 10 years after
the date of purchase. Switching to an equivalent product may occur if
Milleteknik deems that repair is not possible. Support costs may (at
Milleteknik discretion) occur after the warranty period has expired.
12.8.2. Support
Do you need help with installation or connections? Our support phone is
available: Monday-Thursday 08: 00-16: 00 and Fridays 08: 00-15: 00. Telephone
support is closed between 11: 30-13: 15.
You can also send e-mail, we respond, on weekdays, usually in 24 hours.
Phone: +46 31-340 02 30
SPARE PARTS
Support handles questions about spare parts, see contact information above.
QUESTIONS ABOUT PRODUCT PERFORMANCE?
Contact sales: 46 31-340 02 30, e-mail:
sales@milleteknik.se
12.8.3. Country of manufacture
Country of manufacture / country of origin is Sweden. For more information,
contact your seller.
12.8.4. Designed and produced by: Milleteknik AB Designed and produced by
Milleteknik AB
12.9. Batteries – recommended, not included
12.9.1. Batteries are not included they are sold separately Batteries are sold
separately.
12.9.2. 14 Ah, 12 V AGM battery
Fits in | Number of batteries |
---|---|
PoE Switch 4p FLX M+ | 4 |
Battery type | V |
--- | --- |
Maintenance-free AGM, lead-acid battery. | 12 V |
Table 10. 10+ Design life * battery
Article number| E-number| Article name| Terminal|
Measure. Height width depth| Weight per piece| Make
---|---|---|---|---|---|---
MT113-12V14-01| 5230537| UPLUS 12V 14Ah 10+ Design Life battery| Flat pin 6.3
mm| 151x98x101 mm| 4.2 kg| UPLUS
- Design Life is the durability this year for unused battery. Environmental factors such as heat and load affect service life. Batteries that have a durability (+10 Design lLife) of 10+ years usually need to be replaced after 4-5 years.
PRODUCT LIFE CYCLE, ENVIRONMENTAL IMPACT AND RECYCLING
The product is designed and constructed for a long service life, which reduces the environmental impact. The product’s service life depends on, among other things, environmental factors, mainly ambient temperature, unforeseen load on components such as lightning strikes, external damage, handling errors, and more. Products are recycled by being handed over to the nearest recycling station or sent back to the manufacturer. Contact your distributor for more information. Costs that arise in connection with recycling are not reimbursed.
ADDRESS AND CONTACT DETAILS
Milleteknik AB
Ögärdesvägen 8 B
S-433 30 Particle Sweden
+46 31 340 02 30
info@milleteknik.se
www.milleteknik.se
This page is intentionally left blank.
Documents / Resources
|
milleteknik 350-091 PoE Switch 4p FLX M+ PoE Switch with Battery
Backup
[pdf] User Manual
350-091 PoE Switch 4p FLX M PoE Switch with Battery Backup, 350-091, PoE
Switch 4p FLX M PoE Switch with Battery Backup, PoE Switch 4p FLX M PoE
Switch, FLX M PoE Switch, PoE Switch, Switch
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>