milleteknik 350-205 PoE Switch 4p M PoE Switch with Battery Backup User Manual
- June 11, 2024
- Milleteknik
Table of Contents
- ABOUT POE FROM MILLETEKNIK
- HOW POE POWERS DEVICES CONNECTED TO THE POWER SUPPLY
- COMPONENT OVERVIEW POE M
- WALL MOUNTING
- CONNECTION OF BATTERIES
- MOTHERBOARD – DESCRIPTION
- COMMISSIONING – HOW TO START THE UNIT
- STATUS INDICATIONS
- MAINTENANCE
- FAQ – POE
- LIMITATIONS
- PRODUCT LIFE CYCLE, ENVIRONMENTAL IMPACT AND RECYCLING
- ADDRESS AND CONTACT DETAILS
- Documents / Resources
350-205 PoE Switch 4p M PoE
Switch with Battery Backup
User Manual
ABOUT POE FROM MILLETEKNIK
The series is designed to power PoE devices such as access systems,
surveillance cameras and other equipment that can be operated with Power over
Ethernet. Through its function as a battery backup, the PoE device can
continue to be powered in the event of a power failure.
PoE switch 4p M, PoE switch 4p FLX S+ and PoE switch 4p FLX M+ are for
security systems where a, reliable power supply with battery backup and PoE
function is needed. Our PoE have something we call “controlled charging”,
which is a safety function that means that batteries are not charged with more
than 0.5 A. By controlling the charging of batteries, the lifespan of
batteries is significantly extended.
HOW POE POWERS DEVICES CONNECTED TO THE POWER SUPPLY
Connect external devices to be powered via PoE in ports 1-4.
Connect other devices that do not need to be operated with PoE in LAN1-2.
COMPONENT OVERVIEW POE M
Table 1. Component overview
Symbol | Explanation |
---|---|
A | Casing in powder-coated sheet metal. |
B | Space for batteries. |
C | PoE switch. |
D | Power supply unit. |
E | Motherboard. |
F | Cable entries. |
WALL MOUNTING
Use four screws suitable for the wall to set up the cabinet.
The distance between the screw head and the wall should be 1.5–2 mm.
Preferably leave a 100 mm air gap around the unit.
CONNECTION OF BATTERIES
Battery wiring is mounted on the circuit board upon delivery. Pictures below only show how to connect wiring.
- Place the batteries in the cabinet with the battery terminals facing outwards, against the cabinet door.
- Connect the battery cable. Red cable on plus and black cable on minus.
• If possible, disconnect mains voltage when replacing the battery.
Figure 1. Wiring diagram for batteries in battery backup
MOTHERBOARD – DESCRIPTION
See technical data for more information.
Figure 2. CEO
The motherboard controls the device and distributes power. See technical data
for more information.
Table 2. Circuit board overview, explanation
No | On the circuit board | Explanation |
---|---|---|
1 | J24 | Connection for control of power supply. |
2 | D6 | LED 1. |
3 | J11 | connection external LED. |
4 | D11 | LED 2. |
5 | JU2 | Control of alarm threshold. |
6 | JU3 | Connection to external alarm. |
7 | J6 | Connection to buzzer. |
8 | P2:3-5 | Connection to sum alarm. |
9 | P2:1-2 | Load output |
10 | P1:1-3 | Connection to the mains. |
6.1. Connect the mains to the motherboard (PCB)
6.1.1. Connect mains
Pull wiring through the cable entry on the cabinet.
If possible, secure the mains cable with cable ties where possible.
Electrical network cabling shall be kept separate from other cabling to avoid
EMC interference.
Figure 3. Connect the mains to the motherboard
Connect the mains cable to the terminal before it is put back on the
motherboard. Secure F and N with cable ties for electrical safety.
Table 3. Electrical network connections
Letter | Explanation |
---|---|
F | Phase |
N | Neutral |
PE | Protective earth |
ELECTRICAL MAINS CONNECTION 230 V AC ON CIRCUIT BOARD
Check that the marking on the circuit board matches the cable arrangement on
the terminal block.
6.2. Connect load
MAX CURRENT
Maximum current must not be exceeded. Maximum current is indicated on the
Demarking on the unit.
Table 4. Load connections
Circuit board number | Explanation |
---|---|
P2: 1 | Connection for load 1 + |
P2: 2 | Connection for load 1 – |
6.3. Control alarm limit
Alarm for low battery voltage in battery operation can be controlled.
By jumpering JU2, the limit for when the unit should give an alarm can be
lowered.
Alarms are given when the battery voltage in battery drops below the limit.
Table 5. Alarm limits
Alarm limit at low battery voltage | 12 V | 24 V |
---|---|---|
JU2 with jumper* | 10.2 V | 24.0 V |
JU2 without jumper * | 13.2 V | 26.5 V |
Alarm limit at low battery voltage | 12 V | 24 V |
--- | --- | --- |
*The unit is delivered with jumper on JU2
COMMISSIONING – HOW TO START THE UNIT
The unit works normally when the indicator LED on the outside of the cabinet
door lights up with a solid green light. See front panel for other status
indications.
It may take up to 72 hours before the batteries are fully charged.
STATUS INDICATIONS
Solid green light: normal operation.
Solid yellow glow: Low battery voltage.
Solid red light: Low battery when the load output fuse is blown.
MAINTENANCE
The system with the exception of batteries is maintenance-free when installed in an indoor environment.
battery change
- If possible, disconnect mains (voltage) when replacing the battery.
- Disconnect battery cables. Note how battery cables are mounted before removing them.
- Remove battery fuse between batteries.
- Insert and fasten the new batteries.
- Connect the battery cables in the same way as before.
- Connect battery fuse between batteries.
- Switch on mains voltage. The indicator LED may not be green (up to 72 hours), until the batteries are charged.
- Test the system by briefly disconnecting the mains voltage, (= the load is driven by the batteries), and then switch on the mains voltage again.
FAQ – POE
11. PRODUCT DATA SHEET
11.1. PoE product data sheet / technical data
Figure 4. PoE Switch 4p M
11.1.1. Name, article number and e-number
Name | Article number | E-number (SV) |
---|---|---|
PoE switch 4p M | ME01C10048P02504PU | 5171951 |
More information
11.1.2. About PoE from Milleteknik
The series is designed to power PoE devices such as access systems,
surveillance cameras and other equipment that can be operated with Power over
Ethernet. Through its function as a battery backup, the PoE device can
continue to be powered in the event of a power failure.
PoE switch 4p M, PoE switch 4p FLX S+ and PoE switch 4p FLX M+ are for
security systems where a, reliable power supply with battery backup and PoE
function is needed. Our PoE have something we call “controlled charging”,
which is a safety function that means that batteries are not charged with more
than 0.5 A. By controlling the charging of batteries, the lifespan of
batteries is significantly extended.
PRIMARY SWITCHED FOUR-PORT POE BATTERY BACKUP 48 V, 125 W WITH ROOM FOR FOUR 7
AH BATTERIES PoE switch 4p M is for security systems where simple, reliable
power supply with battery backup and PoE function is needed. The products have
something we call “controlled charging”, which is a safety function that means
that batteries are not charged with more than 0.5 A. By controlling the
charging of batteries, the lifespan of batteries is significantly extended.
PoE 4p M must be wall mounted. PoE 4p M is delivered incl. 1x PoE switch with 2x LAN ports & 4x PoE ports. Max power per port: 30.8W (22W@41VDC/at deep discharge of batteries). PoE Budget: 125W. Support for PoE standard IEEE 802.3af/15.4W per port & IEEE 802.3at/30.8W per port. Protection for; overload, over voltage, over temperature, short circuit and deep discharge. Alarm for (1 output): Delayed mains failure alarm (52.8V) or low battery voltage (48V). 1 single-pole (+) fused output (glass fuse) for feeding the PoE switch. The fanless enclosure is painted white with structure, LED for alarm indication and equipped with sockets in the plate for stripping network cables. 2 year warranty. PoE Medium is mainly used in security systems where a simple and reliable power supply with battery backup & PoE function is needed. PoE Medium offers CONTROLLED CHARGING, which means that the batteries are never charged with more than 0.5A. This prevents the batteries from being overcharged and significantly extends their life. The PoE series can be used with AGM batteries. The product is tested and verified against Axema access systems and Dinbox access systems and is therefore recommended for use only with these systems.
Power over Ethernet from Milleteknik
- PoE for security applications with the need for power supply with backup power.
- Proven, reliable technology.
- For fixed installation.
- Swedish made.
Limitations
IMPORTANT
Note that 802.3at type2 is not supported, as the PoE card lacks a handshake
function for type 2. Read more. [11] The product is tested and verified
against Axim access systems and Din box access systems and is therefore
recommended for use only with these systems. The product is currently not
recommended for other products that have an aft/at handshake procedure. The
product deviates from standard IEEE 802.3af per port and IEEE 802.3at as the
power is modified to be used together with Axim passer system and Din box
passer system, which leads to shortcomings, (PoE-connected product does not
start), against products that require handshake.
11.1.5. Areas of use
- Power supply for camera surveillance and other applications that can be powered by PoE.
- Security applications powered by PoE that need backup power in the event of a power outage.
11.1.6. Alarm
The device alarms for:
Low battery voltage, low battery voltage in the event of a broken fuse on the
load output.
11.1.7. Fixed installation
The product is intended for fixed installation. The battery backup must be
installed by a qualified installer.
11.1.8. Battery types
The ECO series can be used with AGM batteries. Do not mix types of batteries,
brand or used and new batteries.
11.2. Regulations and certifications
11.2.1. Requirements that the product meets
EMC: | EMC Directive 2014 / 30EU |
---|---|
Electricity: | Low voltage directive: 2014/35 / EU |
EN 60950-1
PoE:| IEEE 802.3af, IEEE 802.3at/30.8 W Note that 802.3at type2 is not
supported, as the PoE card lacks a handshake function for type 2.
CE:| CE directive according to: 765/2008
Emission:| EN61000-6-: 2001 EN55022: 1998: -A1: 2000, A2: 2003 Kloss B,
EN61000-3-2: 2001
EN55022 (CISPR22), GB9254 Class B, EN55014, EN61000-3-2Class A( 75%
Load),EN61000-3-3
11.3. Expected operating time in the event of a power failure ( with new batteries)
PoE| Bat- tery| Power 15.4 W| Power 30.8 W|
Power 62 W| [vs.] Effect 90 W| Power 100 W| Power
120 W| Power 180W| Power 240 W
---|---|---|---|---|---|---|---|---|---
PoE switch 4p M (48 V)| 4 pcs 7.2 Ah| 18 h 30 min.| 8 h 30 min.| 3 h 45 min.|
–| 2 h| 1 h 45 min.| –| –
11.4. Circuit boards – Technical data
11.4.1. Technical data: CEO 3
Table 6. CEO3 V 2.5
Info | Explanation |
---|---|
Article title | CEO3 |
Info | Explanation |
--- | --- |
Product description | CEO 3 is the next generation circuit board for simpler |
battery backups. Advanced functions that were not previously possible in
simpler battery backups are now available as standard. CEO 3 is a reliable
heart in simpler battery backups with fewer components than before, which
reduces the environmental impact.
Measure| 120 x 55 mm x 52 mm
Own consumption| 32 mA
Fuse on output| F1: T2.5A, mains fuse.
F6: T5A, load fuse +, P2:1.
F7: T16A, battery fuse.
Outputs| One cargo outlet, fused.
Insurance| Load output: + secured.
Alarm via| Triggered load securing, potential-free shifting. Conclusion CO /
NO. PRO1: Via alarm terminal J13 (NC- CO). PRO2: Via alarm terminal J13 (NC-
CO). PRO2 v3: Via J11 and J12 to motherboard on to the parent system. PRO 3:
Via J11 and J12 to motherboard on to the parent system.
Protection against:| Deep discharge, short circuit, overload and overvoltage.
Table 7. Indications
Indicator diode | Green | Orange | RED |
---|---|---|---|
(2) / D2 | OK | Low battery voltage / fuse fault. | Low battery voltage with |
broken fuse on output.
(4) / D11| –| Overvoltage.| Batteries incorrectly connected.
Table 8. Alarm limits
Alarm limit at low battery voltage | 48 V |
---|---|
(5) / JU2 with jumper | 50.5 V |
(5) / JU 2 without jumper | 48 V |
The unit is delivered without a jumper on (8) / JU2
Table 9. sum alarm
sum alarm
(8) P2: 3| NO
(8) P2: 4| CO
(8) P2: 5| NC
11.4.2. Technical data: PoE card
LIMITATIONS
IMPORTANT
Note that 802.3at type2 is not supported, as the PoE card lacks a handshake
function for type 2. Read more. [11] The product is tested and verified
against Axim access systems and Din box access systems and is therefore
recommended for use only with these systems. The product is currently not
recommended for other products that have an aft/at handshake procedure. The
product deviates from standard IEEE 802.3af per port and IEEE 802.3at as the
power is modified to be used together with Axim passer system and Din box
passer system, which leads to shortcomings, (PoE-connected product does not
start), against products that require handshake.
Prod- uct| Num ber of PoE / LAN ports| Max power
per port| PoE budget| Ether- net type| Net- work
ports| Interface| Func- tions| Type, injec tor and
switch
---|---|---|---|---|---|---|---|---
PoE switch 4p M| 4/2| 30,8 @ 54,6 V DC| 125 W| Fast Ethernet Mbit PoE switch|
10 / 100 PoE| 1000Base-T RJ-45| Auto-negotiation, Auto-uplink (auto
MDI/MDIX)| Unman- aged. There is no soft- ware inter- face to con- trol the
switch.
11.5. Power supply
11.5.1. Power supply – Technical Data LRS-150-48
Info | Explanation |
---|---|
Output voltage | 54.6 V |
Output current | 0 A – 3.3 A |
Output voltage, ripple | 200 mVp-p |
Overvoltage | 55.2 V – 64.8 V |
Voltage recharge, ripple / current limitation | Less than 0.6 Vp-p |
Efficiency | 90% |
Current limitation | 110% – 140% |
Constant voltage | +/- 0.5% |
Regulatory accuracy | * / – 1.0% |
Input current (230 V) | 1.7 A |
Mains voltage frequency | 47 Hz- 63 Hz |
Mains voltage | 230 V AC – 240 V AC |
Brand effect | 158.4 W |
Temperature range | -30°C – +70°C |
Humidity range | 20% – 90% RH non-condensed |
The power supply is adapted and calibrated with the battery / hardware of the battery backup. Only power and calibrated power supplies may be used. Contact support when changing power supplies. Use of power supplies coming from another source may cause damage not covered by the warranty. Warranty is canceled if power supplies (from a source other than support / designated by support) that are not correctly calibrated are used.
11.6. Technical data enclosures
11.6.1. Enclosures – Technical Data M
Info | Explanation |
---|---|
Name | M |
Enclosure class | IP 20 |
Measure | Height: 242 mm, width: 350 mm, depth: 150 mm. |
Height units | – |
Mounting | Wall |
Ambient temperature | + 5 ° C – + 40 ° C. For best battery life: + 15 ° C to + |
25 ° C.
Environment| Environmental class 1, indoors. 20% ~ 90% relative humidity
Material| Powder coated sheet
Info| Explanation
---|---
Color| White
Cable entries, number| 5
Batteries that fit| 2 pcs 12 V 7.2 Ah or
2 pcs 12 V 14 Ah.
4 pcs 12 V 7.2 Ah
11.7. Link to the latest information
Products and software are subject to updates, you will always find the latest
information on our website. PoE series
11.8. Warranty, support, country of manufacture and country of origin
11.8.1. Warranty
The product has a two-year warranty, from the date of purchase (unless
otherwise agreed). Support during the warranty period can be reached at
support@milleteknik.se or telephone, +46
31-34 00 230. Compensation for travel and / or working hours in connection
with locating faults, installing repaired or replaced goods is not included in
the warranty. Contact Milleteknik for more information. Milleteknik provides
support during the product’s lifetime, however, no later than 10 years after
the date of purchase. Switching to an equivalent product may occur if
Milleteknik deems that repair is not possible. Support costs may (at
Milleteknik discretion) occur after the warranty period has expired.
11.8.2. Support
Do you need help with installation or connections? Our support phone is
available: Monday-Thursday 08: 00-16: 00 and Fridays 08: 00-15: 00. Telephone
support is closed between 11: 30-13: 15.
You can also send e-mail, we respond, on weekdays, usually in 24 hours.
Phone: +46 31-340 02 30
SPARE PARTS
Support handles questions about spare parts, see contact information above.
QUESTIONS ABOUT PRODUCT PERFORMANCE?
Contact sales: 46 31-340 02 30, e-mail:
sales@milleteknik.se
11.8.3. Country of manufacture
Country of manufacture / country of origin is Sweden. For more information,
contact your seller.
11.8.4. Designed and produced by: Milleteknik AB
Designed and produced by Milleteknik AB
11.9. Batteries – recommended, not included
11.9.1. Batteries are not included they are sold separately Batteries are sold
separately.
11.9.2. 7.2 Ah, 12 V AGM battery
Fits in | Number of batteries |
---|---|
PoE switch 4p M | 4 |
Battery type | V |
--- | --- |
Maintenance-free AGM, lead-acid battery. | 12 V |
Table 10. 10+ Design life * battery
Article number| E-number| Article name| Terminal|
Measure. Height width depth| Weight per piece| Make
---|---|---|---|---|---|---
MT113-12V07-01| 5230536| UPLUS 12V 7.2Ah 10+ Design Life battery| Flat pin 6.3
mm| 151 x 65 x 100
mm.
| 2.4 kg| UPLUS
- Design Life is the durability this year for unused battery. Environmental factors such as heat and load affect service life. Batteries that have a durability (+10 Design lLife) of 10+ years usually need to be replaced after 4-5 years.
PRODUCT LIFE CYCLE, ENVIRONMENTAL IMPACT AND RECYCLING
The product is designed and constructed for a long service life, which reduces the environmental impact. The product’s service life depends on, among other things, environmental factors, mainly ambient temperature, unforeseen load on components such as lightning strikes, external damage, handling errors, and more. Products are recycled by being handed over to the nearest recycling station or sent back to the manufacturer. Contact your distributor for more information. Costs that arise in connection with recycling are not reimbursed.
ADDRESS AND CONTACT DETAILS
Milleteknik AB
Ögärdesvägen 8 B
S-433 30 Particle Sweden
+46 31 340 02 30
info@milleteknik.se
www.milleteknik.se
This page is intentionally left blank.
Documents / Resources
|
milleteknik 350-205 PoE Switch 4p M PoE Switch with Battery
Backup
[pdf] User Manual
350-205 PoE Switch 4p M PoE Switch with Battery Backup, 350-205, PoE Switch 4p
M PoE Switch with Battery Backup, M PoE Switch with Battery Backup, Battery
Backup, M PoE Switch, Switch
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>